2013 Scion FR-S Aero Kit/Spoiler - Sparks Parts

Copy and paste this link to your website, so they can see this document directly without any plugins.



Keywords

tape, STEP, Spoiler, Side, Scion, FIVE:AD, Rear, will, where, FR-S, 2013, front, Installation, side, Using, Skirt, backing, Tape, edge, Instructions, page, Front, Adhesion, with, using, sure, supplied, make, clean, apply

Transcript

2013 Scion FR-S
Aero Kit/Spoiler
INSTALLATION INSTRUCTIONS
ALL ISSUES RELATED TO IMPROPER
INSTALLATION RESULTING FROM
NOT ADHERING TO EXACT INSTALL
PROCEDURES WILL NOT BE COVERED
BY FIVE:AD WARRANTY
PLEASE FOLLOW THE INSTRUCTIONS!
FAILURE TO USE ADHESION PROMOTER WILL VOID WARRANTY AND FIVE:AD
WILL NOT BE RESPONSIBLE FOR ANY AERO KITS OR SPOILERS LOOSE OR
MISALIGNED AS A RESULT OF NOT COMPLETING THESE STEPS!
U
Installation Instructions - page 1/20
FIVE:AD 2013 Scion FR-S Aero Kit/Spoiler
DO NOT STORE, PAINT OR
CURE PARTS UNSUPPORTED!
The Lip Kit is manufactured from URETHANE and extreme caution must be used when storing and painting all parts!
Do not store parts in such a way that distorts their original shape. Although
urethane has a memory allowing it to return to its original shape, long term
distortion will result in parts that do not fit properly when installed.
Be sure to properly support the parts when painting them. ALWAYS support
the full length of the parts and not just the ends when painting. Failure to do
so will result in warped and misshapen parts especially if heat is used in the
curing process!
CAUTION: Curing temperature must NOT exceed 120° degrees Fahrenheit
and PARTS MUST BE SUPPORTED DURING CURING PROCESS TO
AVOID WARPING OR DISTORTION! If this happens, make sure part is
properly supported to achieve original shape, reheat, and let part cool
naturally to its original shape. NEVER USE COMPRESSED AIR OR WET
TOWELS TO COOL PARTS! ALLOW TO COOL NATURALLY!
1.
2.
3.
SUPPLIED HARDWARE:
120
Inspect box and all parts for damage before
prepping, painting and installing kit.
If parts are damaged or incorrect, make
note to shipper and contact the dealer
or distributor that shipped your order.
If damage is not immediately reported,
Five Axis will not be responsible for
shipping damage!
- 12 Self tapping screws
- 12 Locking push clips
- 10 Sticks of 3M Adhesion Promoter
- 2 Rolls of 3M tape
• 30’ of 1/2” tape
• 10’ of 3/8” tape (for Rear Spoiler)
- 2 Sets of Die-Cut 3M tape
• Set 1: Ends of spoiler
• Set 2: Curved area of rear spats
- Spoiler Installation Template Pieces
STOCK HARDWARE:
(Removed from vehicle)
FRONT:
- 3 Plastic Push Clips (under side
of front bumper)
U
Installation Instructions - page 2/20
FIVE:AD 2013 Scion FR-S Rear Spoiler
The FIVE:AD 2013 Scion FR-S Aero Kit is
supplied with a roll of 3M tape and 10 sticks of
adhesion promoter. Using one (1) of the sticks of
Adhesion Promoter, install 3M tape to back side
of each Front Spoiler (2 total).
STEP 1: Prior to painting parts requiring
double-sided tape, using 3/4” masking tape, cover
areas where the tape will be applied.
DO NOT apply double-sided tape prior
to painting parts!
STEP 2: After the part is painted, remove the
masking tape and make sure the mounting
surface (Tape Flange) is free from wax, grease and
dirt. Using Isopropyl Alcohol on a soft clean cloth
throughly clean the Tape Flange on the back of
the parts. Using supplied 3M adhesion promoter
sticks, apply the adhesion promoter to the back
of the tape flange on the spoiler where the 3M
tape will be applied.
STEP 3: Install 1/2” 3M tape to Front Spoiler
using image below as guide. Each 3M tape strip
should be one continous length of tape. Repeat
strips #1 and #2 on opposite side of Front
Spoiler.
Be sure to apply 3M tape
leaving about 1/8" gap from
the edge of the part.
Front Spoiler 3M Tape Install
Proper Mounting Technique
2 Adhesion PromoterApplication
3 Strip #1
Strip #2
= 3M Tape Location
*Left side of Front Spoiler shown. Repeat steps on right side.
USE 1/2” TAPE FOR FRONT SPOILER!
U
1 Paint Masking
USE 1/2” TAPE FOR FRONT SPOILER!
Installation Instructions - page 3/20
FIVE:AD 2013 Scion FR-S Aero Kit
Front Spoiler Installation:
After test fitting and painting, use the following
steps for final attaching Front Spoiler to the
vehicle:
HARDWARE NEEDED:
STEP 1: Remove 3, black plastic push clips that
connect the underside of front bumper to splash
guard. *NOTE: These will be re-installed to
secure the Front Spoiler to underside of bumper.
STEP 2: Remove 2 lower stock, philips head
plastic clips in front wheel wells on both sides of
the front bumper. Discard all 4 clips.
**VISUAL ALIGNMENT TO CONFIRM
CORRECT FRONT SPOILER
LOCATION!**
Test fit Front Spoiler to visually see the correct
location for the part. Note where the top edge
aligns with the fog light housing. Ensure there are
NO GAPS in circled areas.
STEP 3a: The correct location for the outside
area of front bumper.
STEP 3b: The correct location for the inner
area of front bumper.
1
2
3a 3b U
Installation Instructions - page 4/20
FIVE:AD 2013 Scion FR-S Aero Kit
Front Spoiler Installation:
(CONTINUED)
STEP 4: Temporarily fit Front Spoiler and mark
off the areas on the bumper above where the part
will attach using painters tape.
*DO NOT REMOVE tape backing yet*
STEP 5: Remove Front Spoiler and prep the 3M
backing tape for final install. Flip the backing over
to the front side of the part and secure using
tape.
STEP 6: Clean the paint surface of the vehicle
where the double face tape will make contact
using wax and grease remover. Using Isopropyl
Alcohol on a soft clean cloth throughly clean the
paint surface where the double face tape will
make contact. Lastly, apply the 3M Adhesion
Promoter where the 3M tape will make contact.
STEP 7: Re-install the Front Spoiler and align
with the painter’s tape on the front bumper.
Remove 3M tape backing, taking care not to break
the red backing off behind the part! Pull in
order and direction of the letters shown
in image!
Repeat these steps on the opposite of side of
front bumper!
4
6
A
B
7
5
U
Installation Instructions - page 5/20
FIVE:AD 2013 Scion FR-S Aero Kit
Front Spoiler Installation:
(CONTINUED)
STEP 8: APPLY PRESSURE to areas
where tape was applied to part!
STEP 9: After confirming proper alignment, using
the the 3 black plastic push clips removed in Step
1, secure the Front Spoiler on the underside of
front bumper.
STEP 10: Using 4 of the supplied plastic, locking
push clips, secure the Front Spoiler on the inside
of both wheel wells (2 clips each side), pushing the
“lock pins” all the way down. .
STEP 11: Front Spoiler Install Complete!
11
*Push in the clip pins until
they are all the way down
8
10
9
U
Installation Instructions - page 6/20
FIVE:AD 2013 Scion FR-S Rear Spoiler
The FIVE:AD 2013 Scion FR-S Aero Kit is
supplied with a roll of 3M tape and 10 sticks of
adhesion promoter. Using one (1) of the sticks of
Adhesion Promoter, install 3M tape to back side
of each Rear Valance piece (2 total).
STEP 1: Prior to painting parts requiring
double-sided tape, using 3/4” masking tape, cover
areas where the tape will be applied.
DO NOT apply double-sided tape prior
to painting parts!
STEP 2: After the part is painted, remove the
masking tape and make sure the mounting
surface (Tape Flange) is free from wax, grease and
dirt. Using Isopropyl Alcohol on a soft clean cloth
throughly clean the Tape Flange on the back of
the parts. Using supplied 3M adhesion promoter
sticks, apply the adhesion promoter to the back
of the tape flange on the spoiler where the 3M
tape will be applied.
STEP 3: Install 1/2” 3M tape to Rear Valance.
Use image below as guide. Be sure to use two (2)
supplied 3M Die-Cut pieces in “S” shaped area on
each Rear Valance piece. The other sections are
three (3) continuous strips of 3M tape.
Be sure to apply 3M tape
leaving about 1/8" gap from
the edge of the part.
Rear Valance 3M Tape Install
Proper Mounting Technique
= Die-Cut 3M pieces
at bend of valance
= Three (3) separate
lengths of 3M tape
3 Strip #1
Strip #2
Strip #3
Die-Cut “S”
Shaped Piece
USE 1/2” TAPE FOR REAR VALANCE!
U
2
Adhesion Promoter
Application
1 Paint Masking
USE 1/2” TAPE FOR REAR VALANCE!
Installation Instructions - page 7/20
FIVE:AD 2013 Scion FR-S Aero Kit
*Use 2 clips per side to secure parts
1
*Use push clips to align
rear valance piece for
tape masking.
Rear Valance Installation:
After test fitting and painting, use the following
steps for final attaching Rear Valance to the
vehicle:
HARDWARE NEEDED:
STEP 1: Use supplied push clips to help hold the
part in place for tape masking.
*DO NOT PUSH CLIP LOCK PINS IN
ALL THE WAY YET!*
STEP 2: Verify the correct location for the Rear
Valance piece.
CONFIRM PROPER ALIGNMENT. Check
final install location for Rear Valance piece to
ensure there are NO GAPS in the circled areas
shown in image.
While temporarily fitting first side of Rear Valance,
mark upper edge using painter’s tape for the areas
on the bumper where the part will align and
attach.
*DO NOT REMOVE tape backing yet*
STEP 3: Remove Rear Valance piece and flip the
backing over to the front side of the part and
secure using tape.
2
3
U
Installation Instructions - page 8/20
FIVE:AD 2013 Scion FR-S Aero Kit
Rear Valance Installation:
(CONTINUED)
STEP 4: Remove Rear Valance piece and clean
the paint surface of the vehicle where the double
face tape will make contact using wax and grease
remover. Using Isopropyl Alcohol on a soft clean
cloth throughly clean the paint surface where the
double face tape will make contact. Lastly, apply
the 3M Adhesion Promoter where the 3M tape
will make contact.
STEP 5: Align the Rear Valance piece with the
painter’s tape on the rear bumper and remove 3M
tape backing, taking care not to break the red
backing off behind the part! Pull in order and
direction of the letters shown in image!
STEP 6: APPLY PRESSURE to areas
where tape was applied to part!
STEP 7: Use two of the supplied black push
clips to secure the Rear Valance piece. Push “lock
pins” ALL the way down.
STEP 8: First side complete!
*Repeat steps 1-8 on other side of rear
bumper.
5
A
C
D
B
6
4
*Push in the clip pins until
they are all the way down
7 8
U
Installation Instructions - page 9/20
FIVE:AD 2013 Scion FR-S Rear Spoiler
The FIVE:AD 2013 Scion FR-S Aero Kit is
supplied with a roll of 3M tape and 10 sticks of
adhesion promoter. Using two (2) of the sticks of
Adhesion Promoter, install 3M tape to back side
of each Side Skirt (1 stick needed per Side Skirt).
STEP 1: Prior to painting parts requiring
double-sided tape, using 3/4” masking tape, cover
areas where the tape will be applied.
DO NOT apply double-sided tape prior
to painting parts!
STEP 2: After the part is painted, remove the
masking tape and make sure the mounting
surface (Tape Flange) is free from wax, grease and
dirt. Using Isopropyl Alcohol on a soft clean cloth
throughly clean the Tape Flange on the back of
the parts. Using supplied 3M adhesion promoter
sticks, apply the adhesion promoter to the back
of the tape flange on the spoiler where the 3M
tape will be applied.
STEP 3a and 3b: Install 1/2” 3M tape to Side
Skirts. Use image below as guide. There needs to
be three (3) continuous strips of 3M tape. Strip
#3 (see below) is a CONTINUOUS strip.
Be sure to apply 3M tape leaving about
1/8" gap from the edge of the part.
Side Skirt 3M Tape Install
Proper Mounting Technique
= 3M Tape LocationREAR of Side Skirt FRONT of Side Skirt
USE 1/2” TAPE FOR SIDE SKIRTS!
U
1
Paint Masking
2
Adhesion Promoter
Application
Strip #1
Strip #3
3a USE 1/2” TAPE FOR SIDE SKIRTS!
Strip #3
Strip #2
3b USE 1/2” TAPE FOR SIDE SKIRTS!
Installation Instructions - page 10/20
Side Skirt Installation:
After test fitting and painting the new Side Skirts,
use the following steps for attaching them to the
vehicle:
HARDWARE NEEDED:
*Be sure to follow the exact order of
this installation process to insure the
correct alignment for the Side Skirts!
STEP 1: Remove 2 lower stock, philips head
plastic clips in the front wheel well. Discard clips.
**VISUAL ALIGNMENT TO CONFIRM
CORRECT SIDE SKIRT LOCATION!**
Test fit Side Skirt and to visually see the correct
location for the Side Skirt. Note where the top
edge meets the door seam. If the stock rocker is
visible the side skirt is TOO LOW!
STEP 2a: The correct location for the FRONT
end of the Side Skirt
STEP 2b: The correct location for the REAR
end of the Side Skirt
2a WRONG!
CORRECT!
UPPER EDGE
IS TOO LOW!
UPPER EDGE
MEETS
DOOR SEAM!
1
FIVE:AD 2013 Scion FR-S Aero Kit
WRONG!
CORRECT!
UPPER EDGE
IS TOO LOW!
UPPER EDGE
MEETS
DOOR SEAM!
2b U
Installation Instructions - page 11/20
FIVE:AD 2013 Scion FR-S Aero Kit
Side Skirt Installation:
(CONTINUED)
STEP 3a and 3b: Temporarily fit the first Side
Skirt and note the areas on the side of the
vehicle where the part will attach using painters
tape.
*DO NOT REMOVE tape backing yet!*
STEPS 4: Remove factory rock chip guard in
door jam.
STEPS 5a and 5b: Remove Side Skirt and
prep the 3M backing tape for final install. Flip the
backing over to the front side of the part and
secure using tape.
U
3b 5a 5b
3a 4
Installation Instructions - page 12/20
FIVE:AD 2013 Scion FR-S Aero Kit
Side Skirt Installation:
(CONTINUED)
STEPS 6: Clean the paint surface of the vehicle
where the 3M tape will make contact using wax
and grease remover. Using Isopropyl Alcohol on a
soft clean cloth throughly clean the paint surface
where the 3M tape will make contact.
STEPS 7: Apply the 3M Adhesion Promoter
where the 3M tape will make contact to the
body of the vehicle below the tape line at the
REAR and FRONT of door AND below the
door edge on the body.
STEP 8a and 8b: Re-align the Side Skirt with
the painter’s tape on the side of vehicle. Starting
at the BACK of the Side Skirt, remove 3M tape
backing in this EXACT ORDER:
A: With Side Skirt properly aligned PRESS HERE
(A) to secure Side Skirt at correct location
B: Pull tape (B) towards BACK of vehicle
C: Pull tape (C) (image 8b!) towards FRONT of
vehicle
D: Pull tape towards FRONT of vehicle
** WHILE PULLING TAPE (D) BE
SURE TO ALIGN UPPER EDGE OF
SIDE SKIRT ALONG DOOR SEAM
AREA BELOW DOOR FOR CORRECT
INSTALLATION LOCATION! **
U
6
7
B
D
C
8a A
8b Installation Instructions - page 13/20
FIVE:AD 2013 Scion FR-S Aero Kit
Side Skirt Installation:
(CONTINUED)
STEP 9: *APPLY PRESSURE* along Side
Skirt where tape was applied to ensure
proper installation!
STEP 10: Using two of the supplied black,
plastic push clips secure the Side Skirt into the
inside of the front wheel well, pushing the “lock
pins” all the way down.
STEP 11: Using two of the supplied self-tapping
screws, secure the Side Skirt to the inside of the
rear wheel well the the pre-drilled holes in the
Side Skirt.
STEP 12: Using four of the supplied self-tapping
screws, secure the underside of the Side Skirt to
the vehicle by drilling the screws into the stock,
black plastic plugs on under side of vehicle using
the pre-drilled holes in the Side Skirt.
This must be the LAST step to ensure the
proper installation of the Side Skirt.
STEP 13: First Side Skirt install complete!
*Repeat steps 1-13 to install second
Side Skirt.
9
10
*Push in the clip pins until
they are all the way down
11
12 13
U
Installation Instructions - page 14/20
FIVE:AD 2013 Scion FR-S Rear Spoiler
The FIVE:AD 2013 Scion FR-S rear spoiler is
supplied with a roll of 3M tape and 2 sticks of
adhesion promoter. Using one (1) of the sticks of
Adhesion Promoter, install 3M Tape to under side
of rear spoiler.
STEP 1: Prior to painting parts requiring
double-sided tape, using 3/4” masking tape, cover
areas where the tape will be applied.
DO NOT apply double-sided tape prior
to painting parts!
STEP 2: After the part is painted, remove the
masking tape and make sure the mounting
surface (Tape Flange) is free from wax, grease and
dirt. Using Isopropyl Alcohol on a soft clean cloth
throughly clean the Tape Flange on the back of
the parts. Using supplied 3M adhesion promoter
sticks, apply the adhesion promoter to the back
of the tape flange on the spoiler where the 3M
Tape will be applied.
STEP 3: Install 3/8” 3M tape to spoiler. Use
image below as guide. Be sure to use two (2)
supplied 3M Die-Cut pieces for spoiler ends. The
other sections are made up of four (4) continuous strips of 3M tape. Be sure to apply 3M
tape leaving about 1/4" gap from the
edge of the part.
Spoiler 3M Tape Install
Proper Mounting Technique
1 Paint Masking
2
3
= Die-Cut 3M pieces
on ends of spoiler
= 4 separate lengths
of 3M Tape
Strip #1
Strip #2
Strip #3
Strip #4
1/8” gap between strips
1/8” gap between strips
Adhesion Promoter
Application
USE 3/8” TAPE FOR REAR SPOILER!
U
USE 3/8” TAPE FOR REAR SPOILER!
Installation Instructions - page 15/20
FIVE:AD 2013 Scion FR-S Rear Spoiler
Mounting Templates on Decklid
1
2
3
Align to front
edge of decklid
Center template
with 3rd brake light
and Scion logo
Align to front
edge of decklid
Align to side
edge of decklid
Center Template
Edge Template (Right and Left)
Templates Properly Located
FAILURE TO USE TEMPLATES WILL VOID
WARRANTY AND FIVE:AD WILL NOT BE
RESPONSIBLE FOR ANY SPOILERS THAT
ARE NOT PROPERLY ALIGNED OR COME
LOOSE AS A RESULT!
STEP 1: Visually align Center Template with
3rd Brake Light and Scion Emblem.
Make sure front edge of the template is also
aligned with the front edge of the decklid.
Tape Center Template in place with masking
tape on the outer edges.
STEP 2: Align Edge Template with the front
edge and the outer edge of the decklid.
Tape Edge Template in place with masking
tape on the outer edges.
STEP 3: Final Template Installation should
look like this image.
Installation Templates
U
Installation Instructions - page 16/20
FIVE:AD 2013 Scion FR-S Rear Spoiler
Prefit and Alignment
Prefit and Define Area for Adhesion Promoter
Cut tape here!
STEP 1: Place Spoiler on decklid and mark
the edge of part with masking tape or similar
technique.
This will define the area in which the Adhesion
Promoter will be applied.
STEP 2: Make an alignment mark near the
center line of decklid.
Using tape (width not critical) apply a piece
across both the Spoiler and decklid.
This step is a visual reference to ensure easy
alignment at final installation.
1
2
3
Marking Spoiler Perimeter
Taping Alignment Mark
Alignment Mark Complete
STEP 3: Be sure to cut/break the tape
where the Spoiler and decklid meet so the
Spoiler can be removed again.
U
Installation Instructions - page 17/20
FIVE:AD 2013 Scion FR-S Rear Spoiler
STEP 1: Peel backing off and expose about
1” of the 3M adhesive tape.
STEP 2: Fold backing over to the front side
and secure backing to the front face with tape.
1
2
3
Tape Backing Peeled Back
Tape Backing Folded Over & Secured
Tape Backing Peeled Back
STEP 3: Repeat steps above for the end
pieces of 3M adhesive tape as well.
Tape Preparation
Remove Backing and Prep for Mounting
U
Installation Instructions - page 18/20
FIVE:AD 2013 Scion FR-S Rear Spoiler
STEP 1: Apply Adhesion Promoter to the
decklid just inside the taped areas.
Be very careful not to go outside the tape
reference. Adhesion Promoter does stain
painted surfaces.
STEP 3: Pull the tape backing exposing more
of the 3M adhesive tape while simultaneously
indexing the Spoiler against the template and
securing the front top edge to the decklid.
**DO NOT PULL THE BACKING
THE ENTIRE LENGTH YET! ONLY
PULL BACKING TO EDGE OF THE
CENTER TEMPLATE!
Mounting Spoiler
Secure Top Side First
FAILURE TO USE ADHESION PROMOTER
WILL VOID WARRANTY AND FIVE:AD
WILL NOT BE RESPONSIBLE FOR ANY
SPOILERS THAT COME LOOSE AS A
RESULT!
STEP 2: Using the tape alignment mark,
place the Spoiler back on the decklid making
sure the mark is perfectly lined up.
Double check the extreme ends of the Spoiler
to confirm that it is still centered.
1
Apply Adhesion Promoter
2
3
Align Spoiler With Tape Mark
Partially Peel Backing About to the
Edge of The Center Template
Use alignment
mark to line up
Spoiler for final
installation
Stop peeling
backing here!
Apply pressure
here towards
template!
U
Installation Instructions - page 19/20
FIVE:AD 2013 Scion FR-S Rear Spoiler
STEP 6: Carefully check alignment of ends
by indexing Spoiler against template.
Once perfectly aligned and against template,
remove tape backing and secure end of
Spoiler to decklid.
Repeat for other side.
Mounting Spoiler
Secure Top Side First
STEP 5: Center of spoiler should be adhered
to the top of the decklid roughly the width of
the Center Template at this step. DO NOT
FULLY REMOVE TAPE BACKING.
Proceed to outer ends of spoiler for next
step.
4
Adhere Center Upper Portion
5
6
Center of Spoiler Secured to Top of
Decklid
Adhering End of Spoiler to Decklid.
Push here
against
template!
Remove
Corner Piece
Tape Backing
Adhere
CENTER
Area
ONLY!
Stop peeling
backing here!
Push here
against
template!
STEP 4: Pull the tape backing exposing more
of the 3M adhesive tape while simultaneously
indexing the Spoiler against the template and
securing the front top edge to the decklid.
U
Installation Instructions - page 20/20
FIVE:AD 2013 Scion FR-S Rear Spoiler
STEP 8a and 8b: Once top is adhered,
continue to mount the bottom using the similar
method of carefully putting pressure on the
Spoiler against the car while peeling backing
away.
Note: Bottom edge of the Spoiler
should NOT touch the plastic panel
with Scion logo. Bottom edge of spoiler
should be 1/8” away from the panel
gap.
Rear Spoiler Install Complete!
Mounting Spoiler
Adhering the rest of the TOP
STEP 7b: Repeat tape removal from Step
7a on opposite side of spoiler.
STEP 7a: Continue to pull the rest of the
tape backing off while applying pressure to the
Spoiler along the way.
Mounting Spoiler
Adhering the Bottom Edge
Push here!
Push here!
Push here!
Push here!
7b 7a 8a 8b U

PDF Document reader online

This website is focused on providing document in readable format, online without need to install any type of software on your computer. If you are using thin client, or are not allowed to install document reader of particular type, this application may come in hand for you. Simply upload your document, and Docureader.top will transform it into readable format in a few seconds. Why choose Docureader.top?

  1. Unlimited sharing - you can upload document of any size. If we are able to convert it into readable format, you have it here - saved for later or immediate reading
  2. Cross-platform - no compromised when reading your document. We support most of modern browers without the need of installing any of external plugins. If your device can oper a browser - then you can read any document on it
  3. Simple uploading - no need to register. Just enter your email, title of document and select the file, we do the rest. Once the document is ready for you, you will receive automatic email from us.

Previous 10

Next 10