PRODUCT DATA SHEET - Mule-Hide

Copy and paste this link to your website, so they can see this document directly without any plugins.



Keywords

Mule-Hide, with, Adhesive, adhesive, Bonding, this, product, 2013, March, will, should, when, Products, temperatures, than, membrane, contact, material, Material, Co.,, MULE-HIDE, from, using, must, Safety, use., PRODUCT, Inc., containers, This

Transcript

Mule-Hide Products Co., Inc. PRODUCT DATA SHEET
1195 Prince Hall Dr. PDS 09-2405
Beloit, WI 53511 Revision Date: March 2013
MULE-HIDE Low VOC BONDING ADHESIVE
PRODUCT DESCRIPTION
Low VOC Bonding Adhesive is a high strength solvent-based contact adhesive that allows bonding of EPDM and
TPO membrane to various porous and non-porous substrates. It is specially formulated using a blend of VOC
exempt and non-exempt solvents to be meet the < 250 gpl VOC content requirements of the OTC Model Rule for
Single Ply Roofing Adhesives.
This product does not comply with the following California counties’ VOC regulations: Alameda, Contra
Costa, El Dorado, Los Angeles, Marin, Napa, Orange, Riverside, Sacramento, San Bernardino, San Diego, San
Francisco, San Mateo, Santa Clara, Solano, Sonoma, and Tehama. These areas require the use of Mule-Hide
Low-VOC 1168 Bonding Adhesive.
BASIC USES
Mule-Hide Bonding Adhesive is used for bonding cured flashings and membranes to a variety of substrates.
TYPICAL PHYSICAL PROPERTIES
Typical values*
Base Material Synthetic Rubber
Color Yellow
Solids 22.2%
VOC: 250 g/l max
Flash Point 0° F (-17° C) Closed Cup
Brookfield Viscosity 3,300 Centipoises
Avg Net Weight 8.1 lbs. / gallon (3.7 Kg)
Packaging 5 Gallon Pails
Shelf Life 1 Year
*General properties. Typical properties and characteristics are based on samples tested and are not
guaranteed for all samples of this product. This data and information is intended as a guide and does not
reflect the specification or specification range for any particular property of this product.
PACKAGING
5 Gallon Pails
BENEFITS & SUPPLEMENTAL STATEMENTS
• High strength adhesive with quick bonding characteristics
• Ease of application with a medium nap roller
• Provides excellent adhesion between EPDM membranes and a variety of substrates
CODE APPROVALS/COMPLIANCE
A variety of Factory Mutual Ratings and Underwriter Laboratory Classifications are available. Contact Mule-Hide
Technical Department for additional information.
Revised March 2013 PDS 09-2320 Page 1 of 4
Mule-Hide Products Co., Inc. PRODUCT DATA SHEET
1195 Prince Hall Dr. PDS 09-2405
Beloit, WI 53511 Revision Date: March 2013
MULE-HIDE Low VOC BONDING ADHESIVE
COVERAGE RATES
Coverage for Mule-Hide Bonding Adhesive is approximately 60 ft² (5.6 square m) per gallon (finished surface.)
This coverage rate is an average and may vary due to conditions on the job site. Porous surfaces and substrates
may require more bonding adhesive than the typical coverage rate.
INSTALLATION TEMPERATURE
If adhesive is store at temperatures less than 60° F, restore to room temperature (~70° F) before using.
INSTALLATION INSTRUCTIONS
Surface Preparation
1. The surface, on or against which adhesive is to be applied, shall be clean, smooth, dry, free of fins, sharp
edges, loose and foreign materials, oil and grease. Depressions greater than 1/4" (6 mm) should be
feathered; using epoxy, mortar or other approved patching material. All sharp projections shall be
removed by sweeping, blowing or vacuum cleaning.
Application
1. After thorough stirring (minimum 5 minutes), apply Low VOC Bonding Adhesive to substrate and
membrane using a 9" (228 mm) wide, ½” (13mm) medium nap roller. Application shall be continuous and
uniform avoiding globs or puddles. An open time of 5 to 90 minutes, based on drying conditions is
recommended before assembly. Low VOC Bonding Adhesive must be allowed to dry until tacky but does
not string or stick to a dry finger touch. Any coated area, which has been exposed to rain, should be
allowed to dry and then recoated. Do not apply adhesive to seam areas or use with taped products.
2. Roll the membrane onto the adhesive coated substrate while avoiding wrinkles. Immediately brush down
the bonded portion of the sheet with a soft bristle push broom or a clean dry roller applicator to achieve
maximum contact. In some applications, swelling of the membrane may occur initially, but this will
disappear after several days’ exposure. Do not re-broom membrane in an attempt to remove swelling.
REVIEW CURRENT MULE-HIDE SPECIFICATIONS AND DETAILS FOR SPECIFIC APPLICATION
REQUIREMENTS.
Precautions
1. Review the applicable Material Safety Data Sheet for complete safety information prior to use.
2. Low-VOC Bonding Adhesive must be stored in original, unopened containers at temperatures between
60ºF (15ºC) and 90ºF (32ºC). Jobsite storage in excess of 90ºF (32ºC) may affect product shelf life.
Prolonged exposure to below freezing temperatures will cause the adhesive to thicken and solidify in the
can. Should the Low-VOC Bonding Adhesive be stored at temperatures lower than 25ºF (-4ºC), restore to
room temperature for a minimum of 24 hours prior to use. Adhesive will perform as intended once it is
returned to a liquid state. When temperatures are expected to be consistently below 40ºF (4ºC), a heated
enclosure or hot box is required for storage.
Page 2 of 4 PDS 09-2320 Revised March 2013
Mule-Hide Products Co., Inc. PRODUCT DATA SHEET
1195 Prince Hall Dr. PDS 09-2405
Beloit, WI 53511 Revision Date: March 2013
MULE-HIDE Low VOC BONDING ADHESIVE
Precautions (continued)
3. Mule-Hide Bonding Adhesive is EXTREMELY FLAMMABLE -It contains solvents that are dangerous fire
and explosion hazards when exposed to heat, flame or sparks. Do not smoke while applying. Do not use
in a confined or unventilated area. Vapors are heavier than air and may travel along ground or may be
moved by ventilation and ignited by pilot lights, other flames, sparks, heaters, smoking, electrical motors,
static discharge, or other ignition sources at locations distant from material handling point and flashback.
All containers should be grounded when material is transferred from one container to another. A red
caution label is required when shipping. A fire extinguisher should be available. In case of fire, use water
spray, foam, dry chemical or carbon dioxide. Do not use a solid stream of water because it can scatter
and spread the fire.
4. Avoid breathing vapors. Keep container closed when not in use. Use with adequate ventilation. If inhaled,
remove to fresh air. If not breathing, perform artificial respiration. If breathing is difficult, give oxygen. Call
a physician immediately. During application, efforts must be made to prevent fumes from entering the
building via air ventilation ducts. Do not place open containers or mix adhesive near fresh air intake units.
When possible, shut down or seal off the closest units.
5. If swallowed, DO NOT INDUCE VOMITING. Call a physician immediately.
6. Avoid contact with skin. Wash hands thoroughly after handling. In case of contact with skin, thoroughly
wash affected area with soap and water. Contact physician if irritation persists. Note: Permeation resistant
gloves (that meet ANSI/ISEA 105-2005) are recommended to be worn when using this product to protect
hands from irritating ingredients.
7. Avoid contact with eyes. Safety glasses or goggles are recommended. If splashed in eyes, immediately flush
eyes with plenty of clean water for at least 15 minutes. Contact a physician immediately.
8. Do not thin Low-VOC Bonding Adhesive. Thinning will affect performance. Excessively thick or gelled
material should be discarded.
9. These materials are sensitive to ambient moisture and heat will accelerate the effect of moisture. Opened
containers of Bonding Adhesive should be used within 48 hours. Adhesive will begin to thicken after this
point, making it difficult and eventually impossible, to control adhesive thickness. In hot weather, do leave
sealed containers on roof for prolonged periods of time. In cold weather, keep material at room
temperature until ready to use. Stir adhesive occasionally while using.
10. Adhesive must be allowed to dry thoroughly. If membrane is mated with the substrate prior to the
adhesive being dry, blistering will occur.
11. Coverage rates are an average and may vary due to jobsite conditions.
12. KEEP OUT OF THE REACH OF CHILDREN
STORAGE & HANDLING
Job site storage in excess of 90°F (32°C) may affect product shelf life. Should the Mule-Hide Bonding Adhesive be
stored at temperatures lower than 60°F (15°C), restore to room temperature prior to use.
Revised March 2013 PDS 09-2320 Page 3 of 4
Mule-Hide Products Co., Inc. PRODUCT DATA SHEET
1195 Prince Hall Dr. PDS 09-2405
Beloit, WI 53511 Revision Date: March 2013
MULE-HIDE Low VOC BONDING ADHESIVE
PROTECTION & SAFETY
Mule-Hide maintains Material Safety Data Sheets on all of its products. Material Safety Data Sheets contain
health and safety information for your development of appropriate product handling procedures to protect your
employees and customers. Mule-Hide's Material Safety Data Sheets should be read and understood by all of your
supervisory personnel and employees before using Mule-Hide products in your facilities.
ADDITIONAL INFORMATION
The information given on this PDS is subject to change without notice. Always check the Mule-Hide website at
www.mulehide.com for the latest information, changes and updates or contact Mule-Hide Products Company at
800-786-1492.
DISCLAIMER
The statements provided concerning the material shown are intended as a guide for material usage and are believed to be true and accurate at
the time of printing. No statement made by anyone may supersede this information, except when done in writing by Mule-Hide Products Co.,
Inc. Since the manner of use is beyond our control, Mule-Hide does not authorize anyone to make any warranty of merchantability or fitness for
any particular purpose or any other warranty, guarantee or representation, expressed or implied, concerning this material. This product may be
eligible for a Mule-Hide warranty, please check the Mule-Hide website at www.mulehide.com or contact Mule-Hide directly at 800-786-1492 for
details. Buyer and user accept the product under these conditions and assume the risk of any failure, any injury person or property (including
that of the user), loss or liability resulting from the handling, storage or use of the product whether or not it is handled, stored or used in
accordance with the directions or specifications. Mule-Hide must be notified in writing of any claims and be given the opportunity to inspect the
alleged failure before repairs are made.
Page 4 of 4 PDS 09-2320 Revised March 2013

PDF Document reader online

This website is focused on providing document in readable format, online without need to install any type of software on your computer. If you are using thin client, or are not allowed to install document reader of particular type, this application may come in hand for you. Simply upload your document, and Docureader.top will transform it into readable format in a few seconds. Why choose Docureader.top?

  1. Unlimited sharing - you can upload document of any size. If we are able to convert it into readable format, you have it here - saved for later or immediate reading
  2. Cross-platform - no compromised when reading your document. We support most of modern browers without the need of installing any of external plugins. If your device can oper a browser - then you can read any document on it
  3. Simple uploading - no need to register. Just enter your email, title of document and select the file, we do the rest. Once the document is ready for you, you will receive automatic email from us.

Previous 10

Next 10