Intercooler Upgrade Kit P/N 70071 2004-2007 Subaru ... - Turbonetics

Copy and paste this link to your website, so they can see this document directly without any plugins.



Keywords

FIGURE, factory, hose, that, from, using, intercooler, FIGURES, will, Page, 60208_revA.doc, bolts, silicone, socket., 12mm, TURBONETICS, side, have, turbocharger, Install, fitting, Y-pipe, clamps, onto, Spearco, warranty, Remove, under, parts, contact

Transcript

Turbonetics, Inc. * 14399 Princeton Avenue * Moorpark, CA * 805-581-0333 * TurboneticsInc.com
INSTALLATION INSTRUCTIONS
Intercooler Upgrade Kit
P/N 70071
2004-2007 Subaru WRX STi
60208_revA.doc Page 2 of 11
READ THIS FIRST: Study these instructions completely before proceeding. Engine and / or turbocharger
damage may occur if any component within these instructions is improperly installed. Turbonetics, Inc or any of
its distributors cannot be held responsible for damages as a result of negligent or improper installation. This
complete turbocharger system can be installed using common tools and automotive procedures, but installer must
have a thorough knowledge of automotive engine operation and feel comfortable working on the vehicle. If in
doubt, contact Turbonetics’ technical support staff at 805-581-0333, between the hours of 8:00AM and 5:00PM
PST, Monday through Friday.
Remove the heat exchanger from its carton and inspect for any obvious physical damage. All kit components are
thoroughly inspected and carefully packaged prior to shipment from the factory. If any shipping damage is
evident, contact your supplier and request that they process a claim with the shipper involved. Be sure to review
the parts list to verify that you have all necessary system components to proceed. If any components in the parts
list are missing, contact Turbonetics’ customer service staff.
The information contained in this publication was accurate and in effect at the time the publication was approved
for printing and is subject to change without notice or liability. Turbonetics reserves the right to revise the
information presented herein or to discontinue the production of parts described at any time.
SAFETY REQUIREMENTS: It is recommended to follow these precautions.
• Always wear safety glasses & gloves.
• Turn the ignition switch to the OFF position & disconnect the batteries.
• Always use properly rated jack stands when working under the vehicle.
• Prevent unexpected vehicle movement by using wheel chocks and/or parking brake.
• Operate the vehicle only in well ventilated areas.
• Do not smoke or use flammable items near or around the vehicle’s fuel system.
• Keep hands, clothing and other objects away from moving parts when engine is running.
SUPPLIES: It is recommended to have the following items before beginning installation.
• Subaru factory service manual, for your model year
• A large table or bench, and plenty of adjacent available workspace
EST. INSTALL TIME: 2 Hr.
PARTS LIST
Part Number Description Quantity
70070 Heat Exchanger Assembly 1
30315 License Frame – Turbonetics 1
22202-4 2.75” ID x 2.50” Lg Silicone Hose 1
31290 1/2” ID Rubber Hose, J30R9 2 feet
30973 Barb Tube Fitting, 1/2” Tee 1
30971 Barb Tube Fitting, 1/2" Elbow 1
60208 Install Instructions 1
TOOLS REQUIRED
1.) 5/16” or 8mm, 10mm, & 12mm Socket
2.) Socket Extension
3.) Ratchet
4.) Standard selection of automotive tools, primarily metric sizes
60208_revA.doc Page 3 of 11
INSTALLATION
1.) Using a 10mm socket, remove the 3 bolts that secure the factory breather tube that runs along the front
top edge of the factory intercooler, as shown. SEE FIGURES 1 & 2
FIGURE 1 FIGURE 2
2.) Loosen the hose clamp on the silicone hose that connects from the intercooler to the turbocharger using
a flat screwdriver or a 5/16” / 8mm socket. SEE FIGURE 3
FIGURE 3
60208_revA.doc Page 4 of 11
3.) Loosen both hose clamps on the silicone hose between the intercooler and throttle body using a flat
screwdriver or a 5/16” / 8mm socket. Using a 12mm socket, remove the 2 bolts that secure the factory
blow off valve to the factory intercooler. SEE FIGURES 4 & 5
FIGURE 4 FIGURE 5
4.) Remove the bolts that hold the factory intercooler to the vehicle using a 12mm socket. There is 1 bolt on
each side of the intercooler. SEE FIGURE 6-8
FIGURE 6 FIGURE 7
FIGURE 8
60208_revA.doc Page 5 of 11
5.) Remove the factory intercooler from the vehicle. SEE FIGURES 9-10
FIGURE 9 FIGURE 10
6.) Unbolt the factory Y-pipe from the bottom of the factory intercooler by unbolting the 4 bolts using a 12mm
socket. Remove the factory Y-Pipe gaskets and set aside - they will be used later. SEE FIGURES 11-12.
FIGURE 11 FIGURE 12
7.) Remove the rubber grommet from the bracket on each side of the factory intercooler. SEE FIGURE 13
FIGURE 13
60208_revA.doc Page 6 of 11
8.) Re-install the grommets onto the side brackets on the new Spearco intercooler. Make sure the metal
grommet faces upward, so the bolt head will contact the metal, not the rubber. SEE FIGURE 14
FIGURE 14
9.) Re-install the factory Y-pipe and the factory Y-pipe gaskets to the bottom side of the new Spearco
intercooler using the factory bolts and 12mm socket. Loosely re-install the 2 bolts on the ‘long’ leg of the
Y-pipe first, then the ‘short’ leg. You may also need to loosen the silicone hose clamps to help align the
flanges. SEE FIGURES 15-16
FIGURE 15 FIGURE 16
60208_revA.doc Page 7 of 11
10.) Loosely re-install the factory hose clamp onto the outlet of the turbocharger. Install the supplied 2.75”
silicone hose coupling (P/N 22202-4) onto the throttle body and loosely install the 2 factory hose clamps
onto the hose. SEE FIGURES 17-18
FIGURE 17 FIGURE 18
11.) Install the new Spearco intercooler into the vehicle. Connect the 90deg silicone hose on the Y-pipe to
the turbocharger outlet, and the outlet of the intercooler to the new silicone hose on the throttle body.
Tighten the silicone hose clamps. SEE FIGURES 19-20
FIGURE 19 FIGURE 20
60208_revA.doc Page 8 of 11
12.) Re-install the factory blow off valve onto the new Spearco intercooler using the factory bolts and gasket.
Tighten bolts using a 12mm socket. SEE FIGURES 21-22
FIGURE 21 FIGURE 22
13.) Loosely secure the new intercooler to the vehicle using the factory bolts. Adjust as necessary to align
the intercooler to the hood scoop shroud. Tighten bolts using 12mm socket. SEE FIGURES 23-24
FIGURE 23 FIGURE 24
14.) Tighten the silicone hose clamps at the throttle body and turbocharger outlet using 5/16” or 8mm socket.
CONNECTING THE ENGINE BREATHER LINES
15.) Install the supplied tee fitting (P/N 30973) to the factory breather hoses on the passenger side of the
engine. Note the orientation of the tee fitting… connect the hoses to the left & bottom legs of the fitting. It
may be required or desired to slightly trim the hoses to be esthetically symmetrical. SEE FIGURES 25-26
60208_revA.doc Page 9 of 11
FIGURE 25 FIGURE 26
16.) Install the supplied elbow fitting (P/N 30971) to the factory breather hose on the driver’s side of the
engine, with the other leg of the fitting facing the passenger side of the engine. SEE FIGURE 27
FIGURE 27
SUPPLIED RUBBER HOSE
60208_revA.doc Page 10 of 11
17.) Install the supplied 1/2” ID rubber hose (P/N 31290) between the right leg of the tee fitting (passenger
side) and elbow fitting (driver side), routing the hose as desired, and cutting shorter if required. NOTE:
Recommend routing the hose under the factory intercooler bracket on the driver side, then under the
intercooler/throttle body toward the passenger side. SEE FIGURES 28-30
FIGURE 28
FIGURE 29 FIGURE 30
FACTORY I/C BRACKET
SUPPLIED ELBOW FITTING
SUPPLIED RUBBER HOSE
60208_revA.doc Page 11 of 11
FINAL CHECKLIST:
• Review these instructions to make sure that all fasteners, clamps connections have been installed correctly.
• Check that all hose routings are free of any kinks or near any hot or abrasive surfaces, which may cause wear
over time. Adjust or reroute as necessary to provide adequate slack for engine movement.
“NO FAULT / NO HASSLE” WARRANTY PROGRAM:
TURBONETICS will repair or replace, at our expense, any new TURBONETICS / Spearco products that fail,
including products used in racing or competition applications, for a period of one year from the original date of
purchase. All turbocharger and cartridge assemblies have a factory installed inline oil filtration device. This filter
device must remain in place if any warranty is to be considered under the No-Fault / No-Hassle program.
Electrical components that fail due to misuse are not covered under the No-Fault / No-Hassle Warranty Program.
Warranty is limited to TURBONETICS products and does not include progressive or subsequential damage and
does not cover removal or installation labor or associated parts. No warranty is made for any other claims for
special, indirect or consequential damages including but not limited to component removal or installation
equipment downtime, prospective profits or other economic loss.
Warranty will not be granted for recurring damage, malfunction, or failure due to improper installation, misuse,
unauthorized repair or alterations, or externally induced physical damage.
Warranty is non-transferable and must be processed via the original purchaser from TURBONETICS.
Remanufactured units, performance upgraded units, and O.E.M. replacement units are covered by a 90-day
warranty or the O.E. warranty period.
TURBONETICS highly recommends that the installation of mechanical or electrical parts be performed by trained
professionals. Improperly installed products may lead to unsafe and unreliable conditions.
RETURN POLICY:
Only unused and complete merchandise may be accepted for return subject to inspection and acceptance by
TURBONETICS. No goods will be accepted without prior return authorization from TURBONETICS. Call for
approval and RGA (Returned Goods Authorization) tracking number. No returns will be accepted without an RGA
tracking number. No returns will be accepted after ninety (90) days from the original shipping date from
TURBONETICS unless approved. All approved returns are subject to a 15% restocking charge – NO
EXCEPTIONS. The original invoice must accompany the return. Accepted warehouse / distributor and open
account returns will be issued credit only.
RETURNED GOODS AUTHORIZATION TRACKING NUMBER:
TURBONETICS will only accept product returns, repair orders / upgrades, and warranty requests that have been
approved and are returned with a corresponding RGA (Returned Goods Authorization) tracking number.
Contact TURBONETICS for approval and the RGA number. Write the RGA number clearly on the outside of the
package and include it inside the package. This is very important in allowing us to properly identify and process
your request. Failure to comply with this requirement will result in the delay of processing or the product being
returned to you.

PDF Document reader online

This website is focused on providing document in readable format, online without need to install any type of software on your computer. If you are using thin client, or are not allowed to install document reader of particular type, this application may come in hand for you. Simply upload your document, and Docureader.top will transform it into readable format in a few seconds. Why choose Docureader.top?

  1. Unlimited sharing - you can upload document of any size. If we are able to convert it into readable format, you have it here - saved for later or immediate reading
  2. Cross-platform - no compromised when reading your document. We support most of modern browers without the need of installing any of external plugins. If your device can oper a browser - then you can read any document on it
  3. Simple uploading - no need to register. Just enter your email, title of document and select the file, we do the rest. Once the document is ready for you, you will receive automatic email from us.

Previous 10

Next 10