Introduction - Lexus Drivers

Copy and paste this link to your website, so they can see this document directly without any plugins.



Keywords

switch, Touch, touch, screen, switch., screen., display, your, When, will, system, route, this, from, destination, desired, with, page, guidance, vehicle, position, button, current, that, Push, radio, select, input, displayed, (See

Transcript

i Introduction
Thank you for your purchase of the Navigation System. Please read this manual carefully to ensure proper use. Keep this manual
in your vehicle at all times.
The Navigation System is one of the most technologically advanced vehicle accessories ever developed. The system receives satellite signals
from the Global Positioning System (GPS) operated by the U.S. Department of Defense. Using these signals and other vehicle sensors, the
system indicates your present position and assists in locating a desired destination.
The navigation system is designed to select efficient routes from your present starting location to your destination. The system is designed
to direct you to a destination that is unfamiliar to you in an efficient manner. The system uses the maps of DENSO. The calculated routes
may not be the shortest nor the least traffic congested. Your own personal local knowledge or “short cut” may at times be faster than the calculated routes.
The navigation system’s database includes about 75 Point of Interest categories to allow you to easily select destinations such as restaurants
and banks. If a destination is not in the database, you can enter the street address or a major intersection close to it and the system will guide
you there. The system will provide both a visual map and audio instructions. The audio instructions will announce the distance remaining
and the direction to turn in approaching a fork or intersection. These voice instructions will help you keep your eyes on the road and are timed
to provide enough time to allow you to maneuver, change lanes or slow down.
Please be aware that all current vehicle navigation systems have certain limitations that may affect their ability to perform properly.
The accuracy of the vehicle’s position depends on the satellite condition, road configuration, vehicle condition or other circumstances. For more information on the limitations of the system, refer to pages 10 through 12.
ii Important information about this manual
For safety reasons, this manual indicates
items requiring particular attention with the
following marks.
CAUTION
This is a warning against anything
which may cause injury to people if the
warning is ignored. You are informed
about what you must or must not do in
order to reduce the risk of injury to
yourself and others.
NOTICE
This is a warning against anything
which may cause damage to the vehicle or its equipment if the warning is
ignored. You are informed about what
you must or must not do in order to
avoid or reduce the risk of damage to
your vehicle and its equipment.
INFORMATION
This provides additional information.
Initial screen
When you start the engine or turn the ignition
switch to the “ACC” position, the initial
screen appears and the system begins
operating.
CAUTION
When the vehicle is stopped with the
engine running, always apply the parking brake for safety.
After a few seconds, the “CAUTION” screen
appears.
Touch either “English” or
“Français” to select a language. Read
and follow the instructions.
When you touch the “I Agree” switch
on the screen, the map screen appears.
You can access this screen when you push
the “INFO” button and touch the “Language” switch. Then you can select a language.
iii
Safety Instruction
To use your system in the safest possible
manner, follow all the safety tips shown below.
This system is intended to assist you in
reaching your destination and, if used properly, can do so. You, as the driver, are solely
responsible for the safe operation of your vehicle and the safety of your passengers.
Do not use any feature of this system to the
extent it distracts you from safe driving. Your
first priority while driving should always be
the safe operation of your vehicle. While you
are driving, be sure to observe all traffic regulations.
Prior to the actual use of this system, learn
how to use it and become thoroughly familiar
with it. Read the entire Navigation System
Owner’s Manual to make sure you understand the system. Do not allow others to use
this system until they have read and understood the instructions in this manual.
For your safety, some functions may become
inoperable when you start driving. Unavailable switches are dimmed. You can input
your destination and select your route only
when the vehicle is not moving.
CAUTION
 For safety, the driver should not
operate the navigation system while
he/she is driving. Inattention to the
road and traffic may cause an
accident.
 While you are driving, be sure to
obey the traffic regulations and
maintain awareness of the road
conditions. If a traffic sign on the
road has been changed, route
guidance may provide wrong
information such as the direction of
a one way street.
iv While you are driving, listen to the voice instructions as much as possible and glance at
the screen briefly and only when it is safe.
However, do not totally rely on voice guidance. Use it just for your information. If the
system cannot determine your current position correctly, there is a possibility of incorrect, late or non−voice guidance.
The data in the system may occasionally be
incomplete. Road conditions, including driving restrictions (no left turns, street closures,
etc.) frequently change. Therefore, before
you follow any instruction from the system,
look to see whether you can comply with the
instruction safely and legally.
This system cannot warn you about such
things as the safety of an area, condition of
streets, and availability of emergency services. If you are unsure about the safety of an
area, do not drive into it. Under no circumstances is this system a substitute for the
driver’s personal judgement.
Use this system only in locations where it is
legal to do so. Some states/provinces may
have laws prohibiting video screens within
sight of the driver.
v vi 1 North−up or heading−up symbol
This symbol indicates a map view with
north−up or heading−up. Touching this symbol changes the map orientation. 9. . . . . . .
2 Scale indicator
This figure indicates the map scale. 9. . . .
3 “INFO” button
Push this button to display the “Information
Menu” screen. ii, 100, 105, 115. . . . . . . . .
4 Zoom out switch
Touch this switch to reduce the map scale.
9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 “Mark” switch
Touch this switch to register the cursor position as a memory point. 6. . . . . . . . . . . . . . .
6 “Route” switch
Touch this switch to change the route.
46, 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 “DISPLAY” button
Push this button to display the “Display”
screen. 114. . . . . . . . . . . . . . . . . . . . . . . . . . .
— Quick reference
vii
8 “Map View” switch
Touch this switch to obtain information regarding the route to the destination and information about the POI (Points of Interest) on
the map screen. 53, 55, 56. . . . . . . . . . . . .
9 “OFF” switch
Touch this switch to obtain a broader view.
Some of the switches on the screen are not
displayed. They reappear by touching the
“ON ” switch. 93. . . . . . . . . . . . . . . . . . . . .
10 Zoom in switch
Touch this switch to magnify the map scale.
9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 Foot print map switch
Touch this switch to display the foot print
map and the building information. 62. . . . .
12 “MAP/VOICE” button
Push this button to repeat a voice guidance,
cancel one touch scroll, start guidance and
display the current position. 5, 6, 46. . . . .
13 “DEST” button
Push this button to display the “Destination”
screen. viii, 24. . . . . . . . . . . . . . . . . . . . . . . .
14 Screen configuration switch
Touch this switch to change the screen
mode. 57. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 “MENU” button
Push this button to display the “Menu”
screen. x, 20, 65. . . . . . . . . . . . . . . . . . . . . .
16 Distance and time to destination
Displays the distance and the estimated
travel time to the destination. 61. . . . . . . . .
17 “GPS” mark (Global Positioning
System)
Whenever your vehicle is receiving signals
from the GPS, this mark is displayed.
10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 Speech command system indicator
This indicator is shown by pushing the
speech command switch. The speech command system can be operated while this indicator is shown. 112, 114. . . . . . . . . . . . . .
viii
To search for a destination, the switches
below perform the following operations.
1 “Address” switch
You can input the house number and the
street address by using the input keys.
26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 “POI Name” switch
You can select one of the many POIs (Points
of Interest) that have already been stored in
the system’s database. 30. . . . . . . . . . . . . .
3 “POI Category” switch
You can select a destination from the POI
category. 33. . . . . . . . . . . . . . . . . . . . . . . . . .
4 “Previous” switch
You can select a destination from any of the
last 99 previously set destinations and from
the previous starting point. 38. . . . . . . . . . .
5 “Memory” switch
You can select the location from those registered as “Memory points”. (To register
memory points, see page 70.) 37. . . . . . . .
6 “Emergency” switch
You can select one of the three categories of
emergency service points that have been already stored in the system’s database.
36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
— “Destination” screen
ix 7 “Map” switch
You can select a destination simply by
touching the location on the displayed map.
38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 “Intersection” switch
You can enter the names of two intersecting
streets. This is helpful if you do not know the
specific street address of your destination
but know the general vicinity. 39. . . . . . . . .
9 “Freeway Ent./Exit” switch
You can enter the name of a freeway (interstate) entrance or exit. 40. . . . . . . . . . . . . . .
10 “Phone #” switch
You can enter a destination by the telephone
number. 41. . . . . . . . . . . . . . . . . . . . . . . . . . .
11 “Coordinates” switch
You can set a destination using latitude and
longitude as coordinates. 41. . . . . . . . . . . .
12 Quick access switch
You can select one of 5 preset destinations
directly. To use this function, it is necessary
to set the “Attribute” for each memory point.
(To register a “Quick Access”, see page 74.)
26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 Home switch
You can select your own home without entering the address each time. To use this
function, it is necessary to set the “Attribute”
for the memory point. (To register “Home”,
see page 74.) 26. . . . . . . . . . . . . . . . . . . . . .
14 “Change” switch
To change the search area, touch this
switch. 24. . . . . . . . . . . . . . . . . . . . . . . . . . . .
x The switches below perform the following operations.
1 “Map DVD” switch
Displays information regarding the disc version or covered area. 12. . . . . . . . . . . . . . . .
2 “Select User” switch
Enables recall of up to three memorized user
setting patterns. 67. . . . . . . . . . . . . . . . . . . .
3 “Setup” switch
Enables various settings for the navigation
system. 80. . . . . . . . . . . . . . . . . . . . . . . . . . .
4 “My Places” switch
Enables changes to “Memory points” and
“Areas to avoid”. 70. . . . . . . . . . . . . . . . . . . .
5 “Suspend Guidance” and “Resume
Guidance” switch
Suspends or resumes guidance. 66. . . . . .
6 “Volume” switch
Sets the volume for voice guidance.
67. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
— “Menu” screen
1
BASIC FUNCTIONS
Basic information before operation
Display operation 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touch switch operation 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inputting letters and numbers 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current position display 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen scroll operation (one−touch scroll) 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map scale 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Orientation of the map 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limitations of the navigation system 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map database information and updates 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION I
2
Display operation
1U009
You can adjust the angle of the display by
pushing the “TILT” button. Each push of
the “TILT” button will tilt the display to
positions 1 , 2 , 3 and then back to 0 in
the reverse order.
If you turn the ignition switch off, the display
will automatically move back to position 0 .
The display will automatically resume the previous position when the ignition switch is
turned to the “ACC” or “ON” position.
CAUTION
Take care not to jam your hand while
the display is moving. Otherwise, you
could be injured.
NOTICE
Do not obstruct the display while it is
moving. It could damage your navigation system.
INFORMATION
Under extremely cold conditions, the
display may react slowly or operation
sound may become louder.
Touch switch operation
This system is operated mainly by the
switches on the screen. To prevent damage to the screen, lightly touch switches
on the screen with your finger. When you
touch a switch on the screen, a beep
sounds.
Do not use objects other than your finger
to touch the screen.
INFORMATION
 If the system does not respond to a
touch of a switch, move your finger
away from the screen and then touch
it again.
 You cannot operate dimmed
switches.
 Wipe off fingerprints on the surface of
the display using a glass cleaning
cloth.
 The displayed image may become
darker and moving images may be
slightly distorted when the display is
cold.
 Under extremely cold conditions, the
map may not be displayed and the
data input by a user may be deleted.
Also, the switches may be harder
than usual to depress.
3
Inputting letters and numbers
When searching for an address or a name, or
entering a memo, you can input letters and
numbers via the touch screen.
 To input letters
To display the alphabet keys, touch the
“A−Z” switch or the “ ” switch.
Enter letters by touching the alphabet keys directly.
: Touching this switch erases one letter. Holding this switch will continue
to erase letters.
 To input numerals and symbols
To display the number keys and symbol keys,
touch the “0−9” switch.
Enter numerals and symbols by touching the
number keys and symbol keys directly.
: Touching this switch erases one letter. Holding this switch will continue
to erase letters.
: Touching this switch displays other
symbols.
 To display the list
To search for an address or a name, touch the
“List” switch. Matching items from the database are listed even if the entered address
or name is incomplete.
If the number of matches is four or less, the list
is displayed without touching the “List”
switch.
4
INFORMATION
The number of matching items is shown
to the right side of the screen. If the
number of matching items is more than
9,999, the system displays “∗∗∗∗” on
the screen.
 List screen operation
When a list is displayed, you can scroll or
page through the list by using the appropriate
switch.
To shift to the next or previous
page.
To scroll up or down one item at a
time.
This expresses a displayed
screen position.
If appears to the right of the
item name, the complete name is
too long for the display. Touch
to scroll to the end of the name.
Touch to scroll to the
beginning of the name.
5
Current position display
When starting the navigation system, the current position is displayed first.
This screen displays the current vehicle position and a map of the surrounding local area.
The current vehicle position mark appears in
the center or bottom center of the map
screen. You can return to this map screen
showing your current position at any time
from any screen by pushing the “MAP/
VOICE” button.
During driving, the current vehicle position
mark is fixed in the screen and the map
moves.
The current position is automatically set as
your vehicle receives signals from the GPS
(Global Positioning System). If your current
position is not correct, it is automatically corrected after your vehicle receives signals
from the GPS.
INFORMATION
 After battery disconnection, or on a
new vehicle, the current position may
not be correct. As soon as the system
receives signals from the GPS, the
correct current position is displayed.
 To correct the current position manually, see page 81.
Screen scroll operation
(one−touch scroll)
Touch any point on the map and that point
moves to the center of the screen and is
shown by the cursor mark.
If you wish to look at a point on the map which
is different to your current vehicle position,
you can bring the desired point to the center
of the screen by using the scroll feature.
If you continue to hold your finger on the
screen, the map will continue scrolling in that
direction until you lift your finger.
6
After you scroll the screen, the map remains
centered at the selected location until you activate another function. The current vehicle
position mark will continue to move along
your actual route and may move off the
screen. When you push the “MAP/
VOICE” button, the current vehicle position
mark returns to the center of the screen and
the map moves as you proceed along the
designated route.
INFORMATION
When you use the one−touch scroll feature, the current vehicle position mark
may disappear from the screen. Move
the map with a one−touch scroll again or
push the “MAP/VOICE” button to return to the current vehicle position map
location display.
 To set the cursor position as a destination
You can set a specific point on the map as a
destination using the one−touch scroll function.
Touch the “Enter ” switch.
The screen changes and displays the map
location of the selected destination and
the route preference. (See “ — Entering
destination” on page 42.)
If there is already a preset destination, touch
the “Add to ” switch or the “Replace
” switch.
When there is already a preset destination,
using the “Add to ” switch to set an additional destination, will set the new one as the
first point of arrival.
 To register the cursor position as a
memory point
Memory point registration enables easy access to a specific point.
Touch the “Mark” switch.
When you touch the “Mark” switch, the following screen appears for a few seconds, and
then the map screen returns.
7
The registered point is shown by on the
map.
To change the icon or name, etc., see page
72.
You can register up to 106 memory points. If
you attempt to register more than 106, a message appears for confirmation.
 To see information about the icon
where the cursor is set
To display information about an icon, set the
cursor on it.
POI INFORMATION
When the cursor is set on a POI icon, the
name and “Info.” switch are displayed on
the top of the screen.
Touch the “Info.” switch.
Information such as the name, address, and
phone number are displayed.
If you touch the “Enter ” switch, the position of cursor is set as a destination.
If there is already a preset destination, the
“Add to ” switch and the “Replace
” switch are displayed.
When there is already a preset destination,
using the “Add to ” switch to set an additional destination, will set the new one as the
first point of arrival.
To register this POI as a memory point, touch
the “Mark” switch. (For details, see page
70.)
8
INFORMATION
The desired Point of Interest can be displayed on the map screen. (For details,
see page 53.)
MEMORY POINT INFORMATION
When the cursor is set on a memory point
icon, the name and “Info.” switch are displayed on the top of screen.
Touch the “Info.” switch.
Information such as the name, location, and
phone number are displayed.
If you touch the “Enter ” switch, the position of cursor is set as a destination.
If there is already a set destination, the “Add
to ” switch and the “Replace ”
switch are displayed.
When there is already a preset destination,
using the “Add to ” switch to set an additional destination, will set the new one as the
first point of arrival.
To edit a memory point, touch the “Edit”
switch. (For details, see page 72.)
9
Map scale
Touch the or switch to change
the scale of the map display. The scale bar
and indicator at the bottom of the screen indicates the map scale menu. The scale ranges
150 feet (50 m) to 250 miles (400 km).
Touch the or switch until the
scale bar changes normally. If you continue
to touch on the switch, the scale bar changes
smoothly.
You can change the scale of the map display
by touching the scale bar directly. It is not
available during driving.
The map scale is displayed under the north−
up symbol or heading−up symbol at the top
left of the screen.
INFORMATION
When the map scale is at the maximum
range of 250 miles (400 km), is not
shown. When the map scale is at the
minimum range of 150 feet (50 m),
is not shown. However, in the area
where the foot print map is contained,
when the map scale is changed to 150
feet (50 m), the switch changes to
the switch.
Orientation of the map
North−up screen
Heading−up screen
10
You can change the orientation of the map
from North−up to Heading−up by touching
the orientation symbol at the top left of the
screen.
North−up symbol
Regardless of the direction of vehicle travel,
North is always up.
Heading−up symbol
The direction of vehicle travel is always up.
A red arrow indicates North.
Limitations of the navigation
system
This navigation system calculates the current vehicle position using satellite signals, various vehicle signals, map data,
etc. However, the accurate position may
not be shown depending on the satellite
condition, road configuration, vehicle
condition or other circumstances.
The Global Positioning System (GPS) developed and operated by the U.S. Department of
Defense provides an accurate current vehicle
position using 3 to 4 satellites. The GPS system has a certain level of inaccuracy. While
the navigation system will compensate for
this most of the time, occasional positioning
errors of up to 300 feet (100 m) can and
should be expected. Generally, position errors will be corrected within a few seconds.
When your vehicle is receiving signals from
the satellites, the “GPS” mark appears at the
top left of the screen.
The GPS signal may be physically obstructed, leading to inaccurate vehicle position on the map display. Tunnels, tall buildings, trucks, or even the placement of objects
on the instrument panel may obstruct the
GPS signals.
The installation of window tinting may also obstruct the GPS signals. Most window tinting
contains some metallic content that will interfere with GPS signal reception. We advice
against the use of window tinting on vehicles
equipped with navigation systems.
The GPS satellites may not send signals due
to repairs or improvements being made to
them.
11
Even when the navigation system is receiving
clear GPS signals, the vehicle position may
not be shown accurately or inappropriate
route guidance may occur in some cases.
(a) Accurate current vehicle
position may not be shown in
the following cases:
 When driving on a small angled Y−shaped
road.
 When driving on a winding road.
 When driving on a slippery road such as
in sand, gravel, snow, etc.
 When driving on a long straight road.
 When freeway and surface streets run in
parallel.
 After moving by ferry or vehicle carrier.
 When a long route is searched during high
speed driving.
 When driving without setting the current
position calibration correctly.
 After repeating a change of direction by
going forward and backward, or turning on
a turntable in the parking lot.
 When leaving a covered parking lot or
parking garage.
 When a roof carrier is installed.
 When driving with tire chains installed.
 When the tires are worn.
 After replacing a tire or tires.
 When using tires that are smaller or larger
than the factory specifications.
 When the tire pressure in any of the four
tires is not correct.
INFORMATION
If your vehicle cannot receive GPS signals, you can correct the current position manually. For information on setting the current position calibration, see
page 81.
12
(b) Inappropriate route
guidance may occur in the
following cases:
 When turning at an intersection off the
designated route guidance.
 If you set more than one destination but
skip any of them, auto reroute will display
a route returning to the destination on the
previous route.
 When turning at an intersection for which
there is no route guidance.
 When passing through an intersection for
which there is no route guidance.
 During auto reroute, the route guidance
may not be available for the next turn to
the right or left.
 It may take a long time to operate auto reroute during high speed driving. In auto
reroute, a detour route may be shown.
 After auto reroute, the route may not be
changed.
 An unnecessary U−turn may be shown or
announced.
 A location may have multiple names and
the system will announce one or more.
 Some routes may not be searched.
 If the route to your destination includes
gravel, unpaved roads or alleys, the route
guidance may not be shown.
 Your destination point might be shown on
the opposite side of the street.
 When a portion of the route has regulations prohibiting the entry of the vehicle
that vary by time or season or other reasons.
 The road and map data stored in your navigation system may not be complete or
may not be the latest version.
After replacing the tire, implement the operation described in the “ Tire change
calibration”. (For details, see page 82.)
This navigation system uses tire turning data
and is designed to work with factory−specified tires for your vehicle. Installing tires that
are larger or smaller than the originally
equipped diameter may cause inaccurate
display of the vehicle’s position. The tire pressure also affects the diameter of the tires so
please make sure the tire pressure of all four
tires is correct.
Map database information and
updates
This system uses the maps of DENSO.
© GDT, Geographic Data Technology,
Inc.
© 2004 NAVTEQ. All rights reserved.
Data by infoUSA Copyright ©2004, All
Rights Reserved.
© 2004 VISA Corporation
National Research Bureau ©2004
The Bullseye Design is a registered
trademark of Target Brands, Inc.
END USER LICENSE AGREEMENT
PLEASE READ THIS AGREEMENT
CAREFULLY BEFORE USING THE
NAVIGATION SYSTEM
THIS IS A LICENSE AGREEMENT FOR
YOUR COPY OF THE MAP DATABASE
(“The DATABASE”), ORIGINALLY
MADE BY Geographic Data Technology,
Inc. (“GDT”), USED IN THE
NAVIGATION SYSTEM. BY USING THE
DATABASE, YOU ACCEPT AND
AGREE TO ALL TERMS AND
CONDITIONS SET FORTH BELOW.
13
OWNERSHIP
The DATABASE and the copyrights and
intellectual property or neighboring rights
therein are owned by GDT or its
licensors.
LICENSE GRANT
GDT grants you a non−exclusive license
to use your copy of the DATABASE for
your personal use or for use in your
business’ internal operations. This
license does not include the right to grant
sub−licenses.
LIMITATIONS ON USE
The DATABASE is restricted for use in
the specific system for which it was
created. Except to the extent explicitly
permitted by mandatory laws, you may
not extract or re−utilize any portion of the
contents of the DATABASE, nor
reproduce, copy, modify, adapt,
translate, disassemble, decompile, or
reverse engineer any portion of the
DATABASE.
TRANSFER
You may not transfer the DATABASE to
third parties, except together with the
system for which it was created, provided
that you do not retain any copy of the
DATABASE, and provided that the
transferee agrees to all terms and
conditions of this AGREEMENT.
DISCLAIMER OF WARRANTY
GDT does not warrant or make any
representations regarding, either
express or implied, regarding the use or
results of the use of the DATABASE in
terms of its correctness, accuracy,
reliability, or otherwise, and expressly
disclaims any implied warranties of
quality, performance, merchantability,
fitness for a particular purpose or
non−infringement. GDT does not
warrant that the DATABASE is or will be
error free. No oral or written information
or advice provided by GDT, your supplier
or any other person shall create a
warranty.
LIMITATION OF LIABILITY
The price of the DATABASE does not
include any consideration for assumption
of risk of consequential, indirect or
unlimited direct damages which may
arise in connection with your use of the
DATABASE. Accordingly, in no event
shall GDT or supplier of the navigation
system using the DATABASE
(“Supplier”) be liable for any
consequential, special, incidental or
indirect damages, including without
limitation, loss of revenue, data, or use,
incurred by you or any third party arising
out of your use of the DATABASE,
whether in an action in contract or tort or
based on a warranty, even if GDT or the
Supplier has been advised of the
possibility of such damages. In any
event GDT’s liability for direct damages
is limited to the price of your copy of the
DATABASE.
THE DISCLAIMER OF WARRANTY
AND LIMITATION OF LIABILITY, SET
FORTH IN THIS AGREEMENT, DO NOT
AFFECT OR PREJUDICE YOUR
STATUTORY RIGHTS WHERE YOU
HAVE ACQUIRED THE DATABASE
OTHERWISE THAN IN THE COURSE
OF A BUSINESS. Some states and laws
do not allow the exclusion of implied
warranties, so the above disclaimer may
not apply to you.
14
WARNINGS
The DATABASE reflects reality as
existing before you received the
DATABASE and it comprises data and
information from government and other
sources, which may contain errors and
omissions. Accordingly, the DATABASE
may contain inaccurate or incomplete
information due to the passage of time,
changing circumstances, and due to the
nature of the sources used. The
DATABASE does not include or reflect
information on − inter alia −
neighborhood safety; law enforcement;
emergency assistance; construction
work; road or lane closures; vehicle or
speed restrictions; road slope or grade;
bridge height, weight or other limits; road
or traffic conditions; special events;
traffic congestion; or travel time.
GOVERNMENT END USERS
If the DATABASE is for a region of North
America and is being acquired by or on
behalf of the United States government
or any other entity seeking or applying
rights similar to those customarily
claimed by the United States
government, the DATABASE is licensed
with “limited rights.” Utilization of the
DATABASE is subject to the restrictions
specified in the “Rights in Technical Data
and Computer Database” clause at
DFARS 252.227−7013, or the equivalent
clause for non−defense agencies.
Manufacturer of the DATABASE for
North America is Geographic Data
Technology, Inc., at 11 Lafayette Street,
Lebanon, New Hampshire 03766, USA.
END USER NOTICE
PLEASE READ THIS NOTICE
CAREFULLY BEFORE USING THIS
NAVIGATION SYSTEM
The Point Of Interest Data (“POI” Data) in
the navigation system is in part provided
by infoUSA Inc. (“infoUSA”). By using
the POI Data, you accept and agree to all
terms and conditions set forth below.
1. Ownership
All rights, title and interest to the infoUSA
POI Data shall be retained by infoUSA.
2. Limitations on use
Except to the extent explicitly permitted
by mandatory laws, you may not extract
or re−utilize any portion of the contents of
the POI Data, nor reproduce, copy,
modify, adapt, translate, disassemble,
decompile, or reverse engineer any
portion of the POI Data.
3. Transfer
You may not transfer the POI Data to third
parties, except together with the system
for which it was created, provided that
you do not retain any copy of the POI
Data.
15
4. Disclaimer of warranty
EXCEPT AS STATED HEREIN,
INFOUSA MAKES NO EXPRESS OR
IMPLIED WARRANTIES, INCLUDING,
WITHOUT LIMITATION, ANY
EXPRESS OR IMPLIED WARRANTY
OF FITNESS FOR A PARTICULAR
PURPOSE OR WARRANTY OF
MERCHANTABILITY.
5. Limitation of Liability
EITHER INFOUSA OR SUPPLIER OF
POI DATA SHALL NOT BE LIABLE FOR
ANY INDIRECT, CONSEQUENTIAL OR
INCIDENTAL DAMAGES MADE OR
ALLEGED IN CONNECTION WITH
YOUR USE OF THE POI DATA.
END USER LICENSE AGREEMENT
Personal Use Only. You agree to use this
information for solely personal,
non−commercial purposes, and not for
service bureau, time−sharing or other
similar purposes. You may not modify
the information or remove any copyright
notices that appear on the information in
any way. You may not decompile,
disassemble or reverse engineer any
portion of this information, and may not
transfer or distribute it in any form, for any
purpose. Without limiting the foregoing,
you may not use this information with any
products, systems, or applications
installed or otherwise connected to or in
communication with vehicles, capable of
vehicle navigation, positioning, dispatch,
real time route guidance, fleet
management or similar applications.
No Warranty. This information is
provided to you “as is,” and you agree to
use it at your own risk. DENSO and its
licensors (and their licensors and
suppliers, collectively “DENSO”) make
no guarantees, representations or
warranties of any kind, express or
implied, arising by law or otherwise,
including but not limited to, and DENSO
expressly disclaims any warranties
regarding content, quality, accuracy,
completeness, effectiveness, reliability,
fitness for a particular purpose,
non−infringement, usefulness, use or
results to be obtained from this
information, or that the information or
server will be uninterrupted or error−free.
Some states, territories and countries do
not allow certain warranty exclusions, so
to that extent, the above exclusion may
not apply to you.
16
Disclaimer of Liability: DENSO SHALL
NOT BE LIABLE TO YOU FOR ANY
CLAIM, DEMAND OR ACTION,
IRRESPECTIVE OF ITS NATURE,
ALLEGING ANY LOSS, INJURY OR
DAMAGES, WHETHER DIRECT,
INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES,
INCLUDING ANY LOSS OF PROFIT,
REVENUE OR CONTRACTS ARISING
OUT OF YOUR POSSESSION, USE OF
OR INABILITY TO USE THIS
INFORMATION, ANY DEFECT IN THE
INFORMATION, OR THE BREACH OF
THESE TERMS OR CONDITIONS,
WHETHER IN AN ACTION IN
CONTRACT OR TORT OR BASED ON
A WARRANTY, EVEN IF DENSO OR
ITS LICENSORS HAVE BEEN
ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. Some states,
territories and countries do not allow
certain liability exclusions or damages
limitations, so to that extent the above
may not apply to you.
Indemnity. You agree to indemnify,
defend and hold DENSO and its
licensors (including their respective
licensors, suppliers, assignees,
subsidiaries, affiliated companies, and
the respective officers, directors,
employees, shareholders, agents and
representatives of each of them) free and
harmless from and against any liability,
loss, injury (including injuries resulting in
death), demand, action, cost, expense,
or claim of any kind or character,
including but not limited to attorney’s
fees, arising out of or in connection with
any use or possession by you of this
information.
END USER NOTICE
The marks of companies displayed by
this product to indicate business
locations are the marks of their
respective owners. The use of such
marks in this product does not imply any
sponsorship, approval, or endorsement
by such companies of this product.
END−USER TERMS
The Map Data Disc (“Data”) is provided
for your personal, internal use only and
not for resale. It is protected by copyright, and is subject to the following terms
and conditions which are agreed to by
you, on the one hand, and DENSO CORPORATION (“[LICENSEE]”) and its licensors (including their licensors and
suppliers) on the other hand. Such licensors include NAVTEQ North America,
LLC. Without limiting the foregoing, you
agree that NAVTEQ North America, LLC
shall have the right to enforce these
Terms directly against you.
© 2004 NAVTEQ. All rights reserved.
The Data for areas of Canada includes
information taken with permission from
Canadian authorities, including: © Her
Majesty the Queen in Right of Canada, ©
Queen’s Printer for Ontario, © Canada
Post Corporation, Geobase .
17
TERMS AND CONDITIONS
Personal Use Only. You agree to use this
Data for the solely personal, non commercial purposes for which you were licensed, and not for service bureau,
time−sharing or other similar purposes.
Accordingly, but subject to the restrictions set forth in the following paragraphs, you may copy this Data only as
necessary for your personal use to (i)
view it, and (ii) save it, provided that you
do not remove any copyright notices that
appear and do not modify the Data in any
way. You agree not to otherwise reproduce, copy, modify, decompile, disassemble or reverse engineer any portion
of this Data, and may not transfer or distribute it in any form, for any purpose, except to the extent permitted by mandatory laws. You may transfer the Data and
all accompanying materials on a permanent basis if you retain no copies and the
recipient agrees to these End−User
Terms. Multi−disc sets may not be transferred on a divided basis.
Restrictions. Except where you have
been specifically licensed to do so by [LICENSEE] and without limiting the preceding paragraph, you may not (a) use
this Data with any products, systems, or
applications installed or otherwise connected to or in communication with vehicles, capable of vehicle navigation,
positioning, dispatch, real time route
guidance, fleet management or similar
applications; or (b) with or in communication with any positioning devices or any
mobile or wireless−connected electronic
or computer devices, including without
limitation cellular phones, palmtop and
handheld computers, pagers, and personal digital assistants or PDAs.
No Warranty. This Data is provided to
you “as is,” and you agree to use it at your
own risk. [LICENSEE] and its licensors
(and their licensors and suppliers) make
no guarantees, representations or warranties of any kind, express or implied,
arising by law or otherwise, including but
not limited to, content, quality, accuracy,
completeness, effectiveness, reliability,
fitness for a particular purpose, usefulness, use or results to be obtained from
this Data, or that the Data or server will be
uninterrupted or error−free.
Disclaimer of Warranty: [LICENSEE]
AND ITS LICENSORS (INCLUDING
THEIR LICENSORS AND SUPPLIERS)
DISCLAIM ANY WARRANTIES, EX-
PRESS OR IMPLIED, OF QUALITY,
PERFORMANCE, MERCHANTABIL-
ITY, FITNESS FOR A PARTICULAR
PURPOSE OR NON−INFRINGEMENT.
Some States, Territories and Countries
do not allow certain warranty exclusions,
so to that extent the above exclusion may
not apply to you.
18
Disclaimer of Liability: [LICENSEE] AND
ITS LICENSORS (INCLUDING THEIR
LICENSORS AND SUPPLIERS) SHALL
NOT BE LIABLE TO YOU IN RESPECT
OF ANY CLAIM, DEMAND OR ACTION,
IRRESPECTIVE OF THE NATURE OF
THE CAUSE OF THE CLAIM, DEMAND
OR ACTION ALLEGING ANY LOSS, IN-
JURY OR DAMAGES, DIRECT OR IN-
DIRECT, WHICH MAY RESULT FROM
THE USE OR POSSESSION OF THE
INFORMATION; OR FOR ANY LOSS
OF PROFIT, REVENUE, CONTRACTS
OR SAVINGS, OR ANY OTHER DI-
RECT, INDIRECT, INCIDENTAL, SPE-
CIAL OR CONSEQUENTIAL DAM-
AGES ARISING OUT OF YOUR USE
OF OR INABILITY TO USE THIS IN-
FORMATION, ANY DEFECT IN THE IN-
FORMATION, OR THE BREACH OF
THESE TERMS OR CONDITIONS,
WHETHER IN AN ACTION IN CON-
TRACT OR TORT OR BASED ON A
WARRANTY, EVEN IF [LICENSEE] OR
ITS LICENSORS HAVE BEEN AD-
VISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Some States, Territories and Countries
do not allow certain liability exclusions or
damages limitations, so to that extent the
above may not apply to you.
Export Control. You agree not to export
from anywhere any part of the Data provided to you or any direct product thereof
except in compliance with, and with all licenses and approvals required under,
applicable export laws, rules and regulations.
Entire Agreement. These terms and conditions constitute the entire agreement
between [LICENSEE] (and its licensors,
including their licensors and suppliers)
and you pertaining to the subject matter
hereof, and supersedes in their entirety
any and all written or oral agreements
previously existing between us with respect to such subject matter.
Governing Law. The above terms and
conditions shall be governed by the laws
of the Illinois, without giving effect to (i) its
conflict of laws provisions, or (ii) the
United Nations Convention for Contracts
for the International Sale of Goods, which
is explicitly excluded. You agree to submit to the jurisdiction of Illinois for any and
all disputes, claims and actions arising
from or in connection with the Data provided to you hereunder.
Government End Users. If the Licensed
Data is being acquired by or on behalf of
the United States government or any other entity seeking or applying rights similar
to those customarily claimed by the
United States government, (i) for acquisitions conducted by the Department of
Defense, the Licensed Data is licensed
with “Limited Rights” in accordance with
the rights set forth at DFARS
252.227−7013(b)(3), TECHNICAL
DATA−NONCOMMERCIAL ITEMS, and
Licensed Data delivered or otherwise furnished with “Limited Rights” shall be
marked with the following “Limited Rights
Notice” set forth at DFARS
252.227−7013(f)(3), and shall be treated
in accordance with such Notice:
19
LIMITED RIGHTS
CONTRACTOR (MANUFACTURER/
SUPPLIER) NAME:
NAVTEQ North America, LLC
CONTRACTOR (MANUFACTURER/
SUPPLIER) ADDRESS:
222 Merchandise Mart Plaza,
Suite 900, Chicago, Illinois 60654
The Government’s rights to use,
modify, reproduce, release, perform,
display, or disclose these technical
data are restricted by paragraph (b)(3)
of the Rights in Technical Data−Noncommercial Items clause contained in
the above identified contract. Any reproduction of technical data or portions
thereof marked with this legend must
also reproduce the markings. Any person, other than the Government, who
has been provided access to such data
must promptly notify the above named
Contractor.
and; (ii) for civilian agency acquisitions,
the Licensed Data is licensed in accordance with the rights set forth at FAR
52.227−14(g)(1), RIGHTS IN DATA−
GENERAL (Protection of limited rights
data and computer software). In the
event that the Contracting Officer requires the delivery of limited rights Licensed Data that has been withheld or
would otherwise be withholdable in accordance with FAR 52.227−14(g)(1), the
Licensed Data is licensed with “Limited
Rights” as set forth in the following “Limited Rights Notice” at FAR
52.227−14(g)(2) (Alternate II), which
shall be affixed to the Licensed Data and
the Licensed Data shall be treated in accordance with such Notice (which shall
be marked on any reproduction of these
data, in whole or in part):
LIMITED RIGHTS NOTICE
(JUN 1987)
These data may be reproduced and
used by the Government with the express limitation that they will not, without written permission of the Contractor, be used for purposes of manufacture nor disclosed outside the Government; except that the Government may
disclose these data outside the Government for the following purposes, if
any, provided that the Government
makes such disclosure subject to prohibition against further use and disclosure: There are no additional purposes
permitting disclosure of such Data.
The manufacturer/supplier of the Data
is NAVTEQ North America, LLC, 222
Merchandise Mart Plaza, Suite 900,
Chicago, Illinois 60654.
If the Contracting Officer refuses to use
either of the licenses provided in (i) or (ii),
herein, the Contracting Officer must
notify NAVTEQ North America, LLC prior
to seeking additional or alternative rights
in the Licensed Data.
20
There are two types of areas available for
route guidance. In one type of area, primarily around metropolitan centers, detailed route guidance is available for the
entire area. In the other type of area, all
roads are displayed on the map but route
guidance is limited. The navigation route
might lack precision because the data (no
right turns, one−way traffic, etc.) is not
complete. It is still possible to reach the
destination by following the arrow direction and distance as shown on the bottom
left of the screen. The arrow points in the
direction of the destination. The distance
shown is as measured in a straight line
from the current vehicle position to the
destination area.
In order to provide you with as accurate map
information as possible, we are always gathering information such as on road repairs and
carrying out on−site investigations. However,
the names of roads, streets, facilities, and
their locations are often changed. In some
places, construction on roads may be in progress. For that reason, information on some
areas in this system might be different from
the actual location.
The map database is normally updated once
a year. Contact your dealer for information
about the availability and pricing of an update.
 To confirm the database version and
disc coverage area
1. Push the “MENU” button.
2. Touch the “Map DVD” switch.
Make sure the version of the database on this
screen. (The database version on the screen
above may be different from the actual
screen.)
21
To display the disc coverage area, touch the
“Covered Area” switch. Confirm the
covered area on the screen.
Contact your dealer to find out if there is a
more recent update released.
 To replace map disc
The slot for the map disc is behind the display.
To lower the display, push the “OPEN”
button. After replacing map disc, push the
button again to close the display.
CAUTION
 Do not place anything on the opened
display, as such items may be thrown
about in the compartment and possibly injure people in the vehicle during
sudden braking or in an accident.
 To reduce the chance of injury in the
case of an accident or sudden stopping while driving, keep the display
closed.
 Take care not to jam your hand while
the display is moving. Otherwise, you
could be injured.
NOTICE
Do not obstruct the display while it is
moving. It could damage your navigation system.
INFORMATION
Under extremely cold conditions, the
display may react slowly or operation
sound may become louder.
22
23
DESTINATION INPUT AND ROUTE GUIDANCE
Basic functions in frequent use
Destination input 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the search area 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by Home 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by Quick access 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “Address” 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “POI Name” 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “POI Category” 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “Emergency” 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “Memory” 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “Previous” 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “Map” 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “Intersection” 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “Freeway Ent./Exit” 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “Coordinates” 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input by “Phone #” 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting route guidance 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering destination 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Route guidance screen 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical voice guidance prompts 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting and deleting destination 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting and deleting route 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show POI icons 53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Route overview 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Route preview 56. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen configuration 57. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distance and time to destination 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Foot print map 62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION II
24
Destination input —
Push the “DEST” button and the “Destination” screen appears.
You can use one of 13 different methods to
enter your destination. (See pages 26
through 41.)
INFORMATION
 When inputting the destination, the
response to the switch may be slow.
 The route for returning may not be the
same as that for going.
 The route guidance to the destination
may not be the shortest route nor a
route without traffic congestion.
 Route guidance may not be available
if there is no road data for the specified location.
 When setting the destination on a
map with a scale larger than 0.5 mile
(800 m), the map scale changes to 0.5
mile (800 m) automatically. Set the
destination again.
 To select an “Address”, “POI
Name”, “Freeway Ent./Exit”,
“Intersection” or “Phone #” in a
different area, it is necessary to
change the search area.
 If you enter a destination, the road
nearest to the point you selected is
set as the destination.
CAUTION
While you are driving, be sure to obey
traffic regulations and keep the road
conditions in mind. If a traffic sign on
the road has been changed, the route
guidance may provide wrong information.
— Selecting the search area
The “Destination” screen allows you to select
the area to search for your destination.
Touch the “Change” switch on the
“Destination” screen to display a map of
the United States and Canada divided into
11 areas. See page 12 for map database information and updates.
Touch one of the “US1” through “CAN”
switches to select a search area. Touch
the “OK” switch and the “Destination”
screen returns.
25
U.S.A.
Switch States included in the search area
“US1”
Idaho
Oregon
Washington
“US2”
California
Nevada
“US3”
Arizona
Colorado
Montana
New Mexico
Utah
Wyoming
“US4”
Iowa
Kansas
Minnesota
Missouri
North Dakota
Nebraska
South Dakota
“US5”
Oklahoma
Texas
“US6”
Illinois
Indiana
Kentucky
Michigan
Ohio
Wisconsin
“US7”
Arkansas
Alabama
Louisiana
Mississippi
Tennessee
“US8”
Connecticut
Massachusetts
Maine
New Hampshire
New Jersey
New York
Rhode Island
Vermont
“US9”
Washington, D.C.
Delaware
Maryland
New Jersey
Pennsylvania
Virginia
West Virginia
“US10”
Florida
Georgia
North Carolina
South Carolina
Canada
Switch
Provinces and regions included in
the search area
“CAN”
All provinces and regions in
Canada included in this switch.
26
— Destination input by Home
Touch the home switch on the “Destination” screen.
The screen changes and displays the map
location of your home and the route preference. (See “ — Entering destination” on
page 42.)
To use this function, it is necessary to set the
“Attribute” for the memory point. (To register
the “Home”, see page 74.)
INFORMATION
Guidance starts from your current position to your home if you touch the “Enter” switch even while driving.
— Destination input by Quick
access
Touch any of the quick access switches
on the “Destination” screen.
The screen changes and displays the map
location of the quick access point and the
route preference. (See “ — Entering destination” on page 42.)
To use this function, it is necessary to set the
“Attribute” for each memory point. (To register the “Quick Access”, see page 74.)
INFORMATION
Guidance starts from your current position to the quick access point if you
touch the “Enter” switch even while
driving.
— Destination input by
“Address”
There are 2 ways to input a destination by
address.
Touch the “Address” switch on the
“Destination” screen.
27
(a) Inputting a house number
and a street name
Touch numerals directly on the screen to
input a house number.
After inputting a house number, touch the
“OK” switch to display the screen for inputting a street name.
It is possible to input a street name first.
Touch the “Street” switch to display the
screen for inputting a street name.
Input the street name. When you find your desired street name,
touch the corresponding switch.
The screen changes and displays the map
location of the selected destination and
the route preference. (See “ — Entering
destination” on page 42.)
If the same address exists in more than one
city, the current screen changes to the city list
screen.
28
Select or enter your desired city.
“Input Name”: To narrow down the listed
items by inputting the city name.
If you input a street name first, the screen
changes. You can then input the house number.
If the above screen appears, you can select
an address range on the screen.
(b) Selecting a city to search
Touch the “City” switch.
To search by city, the following three methods
are possible.
1. Selecting from the last 5 cities
2. Selecting from the nearest 5 cities
3. Inputting the city name
INFORMATION
To cancel the city setting, touch the
“Any City” switch.
29
SELECTING FROM THE LAST 5 CITIES
Touch the switch of the desired city name.
If you have not used the navigation yet, no cities will be displayed on the screen.
The current screen changes to the screen
for inputting a house number or a street
name. (See page 27.)
SELECTING FROM THE NEAREST 5
CITIES
Touch the “Nearest 5 Cities” switch.
Touch the switch of the desired city name
from the displayed list.
The current screen changes to the screen
for inputting a house number or a street
name. (See page 27.)
INPUTTING THE CITY NAME
Touch the “Input City Name” switch.
Input a city name.
30
Touch the switch of the desired city name
from the displayed list.
“Map”: To display the selected destination
and the route preference. (See “ — Entering
destination” on page 42.)
The current screen changes to the screen
for inputting a house number or a street
name. (See page 27.)
— Destination input by “POI
Name”
Touch the “POI Name” switch on the
“Destination” screen.
Input the name of Point of Interest.
Touch the switch of the desired destination. The screen changes and displays the
map location of the selected destination
and the route preference. (See “ — Entering destination” on page 42.)
If you input the name of a specific Point of Interest and there are more than two sites with
the same name, the list screen appears.
31
Touch the switch of the desired destination.
“Dist. Sort”: In the order of distance from
your current position. The distance from your
current position up to the destination is displayed on the right of the name.
“Name Sort”: In alphabetical order by name.
If the same name exists in more than one city,
you can search for it more easily with the
“City” and “Category” switches. (See
“(a) Selecting a city to search” and “(b) Selecting from the categories”.)
INFORMATION
The desired Point of Interest can be displayed on the map screen. (For details,
see page 53.)
(a) Selecting a city to search
Touch the “City” switch.
To search by city, the following three methods
are possible.
1. Selecting from the last 5 cities
2. Selecting from the nearest 5 cities
3. Inputting the city name
INFORMATION
To cancel the city setting, touch the
“Any City” switch.
SELECTING FROM THE LAST 5 CITIES
Touch the switch of the desired city name.
If you have not used the navigation yet, no cities will be displayed on the screen.
32
SELECTING FROM THE NEAREST 5
CITIES
Touch the “Nearest 5 Cities” switch.
Touch the switch of the desired city name.
INPUTTING THE CITY NAME
Touch the “Input City Name” switch.
Input the city name.
Touch the switch of the desired city name
from the displayed list.
33
(b) Selecting from the
categories
Touch the “Category” switch.
If the desired POI category is on the
screen, touch the name to display a detailed list of the POI category.
If the desired POI category is not on the
screen, touch the “List All Categories” switch to list all POI categories.
When you touch the desired category, the
POI name list screen appears.
— Destination input by “POI
Category”
The destination can be set by selecting the
POI category and the search point.
Touch the “POI Category” switch on
the “Destination” screen.
34
(a) Selecting the POI category
If the desired POI category is on the
screen, touch the name to display a detailed list of the POI category.
If the desired POI category is not on the
screen, touch the “List All Categories” switch to list all POI categories.
Touch the desired POI category from the
list.
The selected category icon appears on the
top left of the screen.
If you wish to delete the selected category,
touch the “Delete” switch.
If you wish to select another category, touch
the “OK” switch to return to the previous
screen.
If you wish to select a destination from the
category displayed by the icon, touch the
“List” switch.
(b) Setting a search point
It is possible to display the names of POIs located within approximately 20 miles (30 km)
from the selected search point.
Touch the “Search Point” switch.
To set search points, the following four methods are possible.
1. Inputting city center
2. Setting the current position as the search
point
3. Setting the search point via the map
screen
4. Setting the search point from the destinations
INPUTTING CITY CENTER
Touch the “Input City Center” switch.
Input the city center name.
Touch the switch of the desired city center
name.
35
When you touch an arrow facing the desired
point, the map scrolls in that direction. When
you release your finger, scrolling stops.
To set the position of the cursor, touch the
“Enter” switch.
SETTING THE CURRENT POSITION AS
THE SEARCH POINT
Touch the “Current Position” switch.
When you touch an arrow facing the desired
point, the map scrolls in that direction. When
you release your finger, scrolling stops.
To set the position of the cursor, touch the
“Enter” switch.
SETTING THE SEARCH POINT VIA THE
MAP SCREEN
Touch the “Map” switch.
When you touch an arrow facing the desired
point, the map scrolls in that direction. When
you release your finger, scrolling stops.
To set the position of the cursor, touch the
“Enter” switch.
36
SETTING THE SEARCH POINT FROM THE
DESTINATIONS
Touch the destination switches at the bottom of the screen.
When you touch an arrow facing the desired
point, the map scrolls in that direction. When
you release your finger, scrolling stops.
To set the position of the cursor, touch the
“Enter” switch.
(c) Selecting from a list
You can select the desired destination from
the listed POI names.
When you touch the switch of the desired
item, the screen changes and displays the
map location of the selected destination
and the route preference. (See “ — Entering destination” on page 42.)
“Dist.”: To sort in the order of distance from
your current location.
“Icon”: To sort in the order of the POI icons.
“Name”: To sort in alphabetical order by
name.
“On Route”: When the indicator is illuminated by touching this switch, the list of the
items searched along the route is displayed.
— Destination input by
“Emergency”
By touching the “Emergency” switch
on the “Destination” screen, the display
changes to a screen to select dealers, hospitals or police stations. During driving,
only nearby police stations, hospitals or
dealers are shown. The current position is
shown with an address, the latitude and
the longitude at the top of the screen.
When you touch the desired emergency category, the selected emergency category list is
displayed.
37
Touch the switch of the desired destination. The screen changes and displays the
map location of the selected destination
and the route preference. (See “ — Entering destination” on page 42.)
“Dist. Sort”: To sort in the order of distance
from your current position. The distance from
your current position up to the destination is
displayed on the right of the name.
“Name Sort”: To sort in alphabetical order by
name.
INFORMATION
The navigation system does not guide in
areas where route guidance is unavailable. (See page 12.)
— Destination input by
“Memory”
Touching the “Memory” switch on the
“Destination” screen displays your list of
registered memory points. See page 70
for registering and editing memory points.
When you touch the switch of your desired memory point, the screen changes
and displays the map location of the selected destination and the route preference. (See “ — Entering destination” on
page 42.)
There are 4 ways to list the memory point
by touching switches on the bottom of the
screen.
“Date”: To list the memory points in order of
registered date.
“Icon”: To list the memory points by the registered icon.
“Name”: To list the memory points in alphabetical order.
“Attribute”: To list the memory points by the
registered attribute.
38
— Destination input by
“Previous”
Touch the “Previous” switch on the
“Destination” screen.
The previous starting point and up to 99 previously set destinations are displayed on the
screen.
Touch the switch of the desired destination. The screen changes and displays the
map location of the selected destination
and the route preference. (See “ — Entering destination” on page 42.)
“Date”: To list the previous destinations in order of registered date.
“Name”: To list the previous destinations in
alphabetical order.
INFORMATION
You can delete the list of previous destinations while your vehicle is stopped,
if you no longer need them. (See page
95.)
— Destination input by “Map”
Touch the “Map” switch on the “Destination” screen.
The screen changes and displays the map
location that was previously displayed
just before the destination input operation
and the route preference. (See “ — Entering destination” on page 42.)
INFORMATION
Guidance starts if you touch the “Enter” switch even while driving. However, the cursor cannot be moved.
39
— Destination input by
“Intersection”
Touch the “Intersection” switch on the
“Destination” screen.
Input the name of the two intersecting
streets which are located near the destination to be set.
Touch the switch of the desired item. After
inputting the two intersecting streets, the
screen changes and displays the map
location of the selected destination and
the route preference. (See “ — Entering
destination” on page 42.)
If the same two streets cross at more than one
intersection, the screen changes and displays the menu to select the city name where
the streets intersect. Select the city, and the
map location of the selected destination and
the route preference. (See “ — Entering destination” on page 42.)
40
— Destination input by
“Freeway Ent./Exit”
To input a freeway entrance or exit, touch
the “Freeway Ent./Exit” switch on the
“Destination” screen.
Be sure to use the complete name of the freeway or highway, including the hyphen, when
entering the destination. Freeways and interstates use an “I” (I−405). US highways use
the state designation before the number
(CA−118).
Select the desired freeway by touching
the switch.
You can then select either a freeway “Entrance” or “Exit”.
Touch the switch of the desired entrance
or exit name. The screen changes and displays the map location of the selected destination and the route preference. (See
“ — Entering destination” on page 42.)
“Dist. Sort”: In the order of distance from
your current position. The distance from your
current position up to the destination is displayed on the right of the name.
“Name Sort”: In alphabetical order by name.
“Input Name”: An applicable list is displayed
by touching this switch and inputting name.
41
— Destination input by
“Coordinates”
Touch the “Coordinates” switch on the
“Destination” screen.
Input the latitude and the longitude.
When the input is finished, touch the “OK”
switch.
When you touch the switch of the desired
point, the screen changes and displays
the map location of the selected destination and the route preference. (See “ —
Entering destination” on page 42.)
— Destination input by
“Phone #”
Touch the “Phone #” switch on the
“Destination” screen.
Input a telephone number.
After inputting a telephone number, touch
the “OK” switch, and the screen changes
and displays the map location of the selected destination and the road preference. (See “ — Entering destination” on
page 42.)
If there is more than one site having the same
number, the following screen appears.
INFORMATION
 If there is no match for the telephone
number inputted, a list of identical
numbers but with different area
codes will be displayed.
 To set a memory point as a destination using the phone number, the
number must be registered previously. (See page 76.)
42
Starting route guidance —
— Entering destination
After you input the destination, the screen
changes and displays the map location of
the selected destination and the route
preference.
SCREEN A
1. When you touch an arrow facing the
desired point, the map scrolls in that
direction. When you release your finger,
scrolling stops.
2. To set the destination and display
SCREEN B, touch the “Enter” switch.
When the destination is already set, the
“Add to ” switch and the “Replace
” switch are displayed.
“Add to ”: To add a destination.
“Replace ”: To delete the existing destinations and set a new one.
“Change”: To change the route preference.
(See page 43.)
“Info.”: If this switch is displayed on the top
of the screen, touch the switch to see name,
address, and phone number, etc.
SCREEN B
3. To start guidance, touch the “Guide”
switch.
“3 Routes”: To select the desired route from
three possible routes. (See page 43.)
“Route”: To change the route. (See pages
46 and 48.)
INFORMATION
 Guidance can be suspended or resumed. (See page 66.)
 If you keep touching the “Guide”
switch until a beep sounds, Demo
mode will start.
43
 To change the route before starting
guidance
ROUTE PREFERENCE
You can change route preference by touching
the “Change” switch on SCREEN A.
You can turn the indicator on or off by
touching the switch.
When searching for a route, the system
avoids routes where the indicator is dimmed
as much as possible.
After choosing conditions, touch the
“OK” switch.
INFORMATION
 Even if the “Allow Freeway” indicator is dimmed, the route cannot
avoid including a freeway in some
cases.
 If the calculated route includes a trip
by ferry, the route guidance shows a
sea route. After you travel by ferry,
the current vehicle position may be
incorrect. Upon reception of GPS signals, it is automatically corrected.
3 ROUTES SELECTION
To select the desired route from three routes,
touch the “3 Routes” switch on SCREEN
B.
Touch the “Quick1”, “Quick2” or
“Short” switch to select the desired
route.
“Quick1”: Recommended route.
This route is indicated by an orange line.
“Quick2”: Other route.
This route is indicated by a purple line.
“Short”: A route by which you can reach the
destination in the shortest distance.
This route is indicated by a green line.
44
“Info.”: To display the following information
about each of the 3 routes.
1 Time necessary for entire trip
2 Distance of entire trip
3 Toll road
4 Freeway
5 Ferry
— Route guidance screen
When starting route guidance, the following
screen is displayed.
This screen displays the route that guides the
driver to the destination.
The route to the destination is indicated by a
highlighted line. Drive along the guided route.
When the vehicle approaches a guidance
point such as an intersection or a freeway, the
screen automatically divides in two to display
the guidance screen. (For details, see page
57.)
The current street name will be displayed at
the bottom of the screen.
In some areas, the roads have not been completely digitized in our database yet. For this
reason, the route guidance may guide the
road that is not allowed to pass.
— Typical voice guidance
prompts
The voice guidance provides various messages as you approach an intersection, or
other point where you need to maneuver the
vehicle.
1 “Proceed about 5 miles.”
2 “In a quarter of a mile, right turn.”
3 “Right turn.”
4 (Beep sound only)
45
INFORMATION
On freeways, interstates or other highways with higher speed limits, the voice
guidance will be made at earlier points
than on city streets in order to allow time
to maneuver.
4.2 miles
0.25 miles
1 “Proceed about 4 miles to the traffic circle.”
2 “In a quarter of a mile, traffic circle
ahead, and then 3rd exit ahead.”
3 “The 3rd exit ahead.”
4 “The exit ahead.”
5 (Beep sound only)
One−way road
One−way road
∗: The system indicates a U−turn if the distance between two one−way roads (of opposite directions) is less than 50 feet (15 m) in
residential areas or 164 feet (50 m) in non−
residential areas.
1 “In half of a mile, make a legal U−
turn.”
2 “Make a legal U−turn ahead.”
3 (Beep sound only)
46
The system announces your approach to the
final destination.
1 “Your destination is ahead.”
2 “You have arrived at your destination. The route guidance is now
finished.”
INFORMATION
 If the system cannot determine the
current vehicle position correctly (in
cases of poor GPS signal reception),
the voice guidance may be made early or delayed.
 If you did not hear the voice guidance
command, push the “MAP/VOICE”
button to hear it again.
 To adjust the voice guidance volume,
see page 67.
Setting and deleting
destination
(a) Adding destinations
You can add destinations and search
again for the routes.
1. Touch the “Route” switch.
2. Touch the “Add” switch of “Destination”.
47
3. Input an additional destination in the
same way as the destination input. (See
page 24.)
4. Touch the desired “Add” switch to
determine the arrival order of the additional destination.
(b) Reordering destinations
When more than one destination is set,
you can change the arrival order of the
destinations.
1. Touch the “Route” switch.
2. Touch the “Reorder” switch of “Destination”.
3. Select the destination in the order of
arrival by touching the switch of destinations.
Reordered number of arrival is displayed on
the right side of the screen.
When you finish selecting the destinations,
touch the “OK” switch. The system
searches for the guidance route again, and
displays the entire route. Even if you do not
touch the “OK” switch, the entire route is
displayed automatically within a few seconds
when order is fixed.
48
(c) Deleting destination
You can delete a set destination.
1. Touch the “Route” switch.
2. Touch the “Delete” switch of “Destination”.
3. When more than one destination is set,
a list will appear on the screen. Touch the
destination on the screen you wish to delete.
“Delete All”: To delete all destinations on the
list.
4. A message appears to confirm your request to delete. To delete the destination(s), touch the “Yes” switch.
If you touch the “Yes” switch, the data cannot be recovered.
If you touch the “No” switch, the previous
screen will return.
5. If more than one destination is set,
touch the “OK” switch after deleting the
destinations. The system searches for the
guidance route again, and displays the entire route.
Setting and deleting route
(a) Adding preferred road
You can add points you wish to pass
through.
1. Touch the “Route” switch.
2. Touch the “Add” switch of “Preferred
road”.
49
3. Select the preferred road which you
wish to modify and touch the “Enter ”
switch.
4. A message appears to confirm your request. To add the preferred road, touch
the “OK” switch.
Touch the “Next” switch to use another
road.
5. If more than one destination is set, the
“Add Preferred Road” screen appears.
Touch the “Add” switch where you wish
to add a preferred road.
(b) Deleting preferred road
You can delete a set preferred road.
1. Touch the “Route” switch.
2. Touch the “Delete” switch of “Preferred road”.
3. When more than one preferred road is
set, a list will appear on the screen. Touch
the switch of the preferred road to be deleted.
50
“Delete All”: To delete all the listed preferred
road.
4. A message appears to confirm your request to delete. To delete the preferred
road, touch the “Yes” switch.
If you touch the “Yes” switch, the data cannot be recovered.
If you want to try again or cancel deletion,
touch the “No” switch. The previous screen
will return.
5. If more than one preferred road is set,
touch the “OK” switch after deleting the
preferred road. The system searches for
the guidance route again, and displays entire route.
(c) Search condition
You can designate the route conditions of
the route to the destination.
1. Touch the “Route” switch.
2. Touch the “Search Condition”
switch. The “Search Condition” screen
appears.
3. Touch the “Quick”, “Quick1”,
“Quick2” or “Short” switch and touch
the “OK” switch.
The entire route from the starting point to the
destination is displayed.
“Guide”: To start guidance.
“Route”: To add or change a route. (For details, see pages 46 and 48.)
51
(d) Detour setting
While the route guidance is operating, you
can change the route to detour around a
section of the route where a delay is
caused by road repairs, an accident, etc.
1. Touch the “Route” switch.
2. Touch the “Detour” switch.
3. Select the switch below to select the
desired detour distance.
“1 mile (km)”, “3 miles (km)” or “5 miles
(km)”: Touch one of these switches to start
the detour process. After detouring, the system returns to the original guidance route.
“Whole Route”: If you touch this switch, the
system will calculate an entire new route to
the destination.
This picture shows an example of how the
system would guide you around a delay
caused by a traffic jam.
1 This position indicates the location of a
traffic jam caused by road repairs or an
accident.
2 This route indicates the detour suggested by the system.
INFORMATION
 When your vehicle is on a freeway, the
detour distance selections are 5, 15,
and 25 miles (km).
 The system may not be able to calculate a detour route depending on the
selected distance and surrounding
road conditions.
52
(e) Route preference
You are given a number of choices on the
conditions which the system uses to determine the route to your destination.
1. Touch the “Route” switch.
2. Touch the “Route Preference”
switch to change the conditions which are
to determine the route to your destination.
3. You can turn the indicator on or off by
touching the switch.
When searching for a route, the system
avoids routes where the indicator is dimmed
as much as possible.
After choosing the conditions, touch the
“OK” switch.
(f) Starting route from
adjacent road
You can start the route guidance from the
adjacent road.
(ex. When the route guidance guides the
route on the freeway, but you drive on the parallel way along a freeway.)
1. Touch the “Route” switch.
2. Touch the “Start from Adjacent
Road” switch.
When there is no adjacent road, this switch
will not appear.
53
Show POI icons
Points of Interest such as gas stations and
restaurants can be displayed on the map
screen. You can also set their location as
a destination and use them for route guidance.
1. Touch the “Map View” switch.
2. Touch the “Show POI Icon” switch
to display a particular type of Point of Interest on the screen.
A screen with a limited choice of Points of Interest will be displayed. (To change the displayed POI, see page 94.) When you touch
the desired Point of Interest category, symbols will appear on the map screen indicating
where the POI addresses are located.
To turn off the symbols of the Points of Interest on the map screen, touch the “POI
Off” switch.
“More”: If you cannot find your desired Point
of Interest on the limited choice screen, touch
this switch. The screen then displays the
complete POI listing screen.
You can display up to 5 categories of icons on
the screen.
54
When you select a Point of Interest type from
either the limited list or the complete list, the
screen will display symbols at those locations
on the map screen.
Touching the “Delete” switch will delete the
last selected icon.
“Local POI List”: If you want to search for the
nearest Point of Interest, touch this switch.
Then choose one of the categories. The system will list the points within 20 miles (30 km).
Touch the switch of your desired Point of Interest. Selected Points of Interest are displayed on the map screen.
“Dist.”: To sort in the order of distance from
your current location.
“Icon”: To sort in the order of the POI icons.
“Name”: To sort in alphabetical order by
name.
“On Route”: When the indicator is illuminated by touching this switch, the list of the
items searched along the route is displayed.
 To set a POI as a destination
You can select one of the Points of Interest
icons on the map screen as a destination and
use it as route guidance.
Directly touch the Point of Interest icon
that you wish to set as a destination.
The map will shift so that the icon is centered
on the screen and overlaps with the cursor
. At this time, the distance from your current position can be displayed on the screen.
The distance shown is measured as a straight
line from the current vehicle position to the
POI.
When your desired Point of Interest overlaps with the cursor, touch the “Enter
” switch. The screen changes and displays the map location of the selected destination and route preference. (See “ —
Entering destination” on page 42.)
55
Route overview
1. Touch the “Map View” switch.
2. Touch the “Route Overview”
switch.
The entire route from the current position to
the destination is displayed.
“Guide”: To start guidance.
“Route”: To change the route. (For details,
see pages 46 and 48.)
“Turn List”: The following screen displays
the list of the roads up to your destination.
You can scroll through the list of roads by
touching or . However, not all road
names in the route may appear on the list. If
a road changes its name without requiring a
turn (such as on a street that runs through two
or more cities), the name change will not appear on the list. The street name closest to
the starting point will be displayed with a mileage to the next turn.
These marks indicate the
direction in which you should turn
at an intersection.
56
Touch the “Map” switch of your desired
point. The point which you choose is displayed on the map screen.
Route preview
1. Touch the “Map View” switch.
2. Touch the “Route Preview” switch.
: To indicate the next destination.
: To preview the route to the next destination.
: To preview the route to the next destination in fast−forward mode.
: To stop the preview.
: To review the route to the previous
destination or starting point.
: To review the route to the previous
destination or starting point in fast−
forward mode.
: To indicate the previous destination
or starting point.
57
Screen configuration
You can choose any one of the screen
configurations.
1. Touch this switch to display the following screen.
2. To select the desired screen configuration, touch one of the following switches.
Depending on the conditions, it may not be
possible to select certain screen configuration switches.
: To display single map screen. (See
page 57.)
: To display dual map screen. (See
page 58.)
: To display compass mode screen.
(See page 58.)
: To display turn list screen. (See page
59.)
: To display arrow screen. (See page
59.)
: To display freeway information
screen. (See page 59.)
: To display intersection guidance
screen or guidance screen on freeway. (See page 60.)
(a) Single map
The screen shows the single map.
58
(b) Dual map
The screen shows the dual map. The map on
the left is the main map.
You can edit the right side map by touching
any specific point on the right side map.
This screen can perform the following
procedures.
 Changing the map scale
 Displaying the POI icon
 Changing the orientation of the map
Touch the “OK” switch when you complete
editing. The screen returns to the dual map
screen.
(c) Compass mode
Information about the destination and current
position, as well as a compass, is displayed
on the screen.
The destination mark is displayed in the direction of the destination. When driving, refer to
the longitude and latitude coordinates and the
compass, to make sure that your vehicle is
headed in the direction of the destination.
INFORMATION
When the vehicle goes out of the disc
area, the guidance screen changes into
compass mode.
59
(d) Turn list screen
The screen shows the turn list. You cannot
scroll through the list of roads.
(e) Arrow screen
The screen shows the current road name and
the distance to the next corner.
(f) Freeway information screen
This screen displays the distance to the next
junction and exit, or POIs in the vicinity of the
freeway exit.
“Map”: To display the selected map of the
exit vicinity.
On the left side of the “Map” switch, up to
five POIs around the selected exit are displayed.
: To scroll for farther junctions or exits.
: To scroll for closer junctions or exits.
: To scroll for the closest three junctions
or exits.
60
INFORMATION
When you drive on a freeway, the screen
is automatically divided into two parts,
with freeway information screen on the
right side.
(g) Intersection guidance
screen/guidance screen on
freeway
 Intersection guidance screen
This screen automatically appears when the
vehicle approaches an intersection on the
road.
The distance to the intersection is shown at
the bottom of the screen.
“OFF”: The intersection guidance screen
disappears and the map screen appears.
When touching the switch or pushing
the “MAP/VOICE” button, the intersection guidance screen reappears.
INFORMATION
Intersection guidance can be turned on
or off. (See page 89.)
 Guidance screen on freeway
This screen automatically appears when the
vehicle approaches a junction or exit on a
freeway.
The distance to the junction or exit is shown
at the bottom of the screen.
“OFF”: The guidance screen on freeway
disappears and the map screen appears.
When touching the switch or pushing
the “MAP/VOICE” button, the guidance
screen on freeway reappears.
INFORMATION
Guidance screen on freeway can be
turned on or off. (See page 90.)
61
Distance and time to
destination
When the vehicle is on the guidance route,
the distance and the estimated travel time
to the destination are displayed. When the
vehicle is not on the guidance route, the
distance to and the direction of the destination are displayed.
When driving on the guidance route and more
than one destination is set, the distance and
the estimated travel time from current position
to each destination are displayed.
1. Touch this switch to display the following screen.
2. Touch the number switch of the destination you wish to display.
The distance and the estimated travel time
from the current position to the selected destination are displayed.
Displayed while driving along the
guidance route.
Displayed while driving off the
guidance route. The destination
direction is indicated by an arrow.
INFORMATION
When the vehicle is on the guidance
route, the distance measured along the
route is displayed. Travel time is calculated based on the set vehicle speed information. (For details, see page 83.)
However, when the vehicle is not on the
guidance route, the distance is the linear
distance between the current position
and the destination.
62
Foot print map
For the area which is covered by the foot print
map (Some areas in the following cities;
Detroit, Chicago, N.Y., L.A), you can switch to
the foot print map on a scale of 75 feet (25 m).
 To switch to the foot print map
The switch changes into the
switch when the map is scaled down to 150
feet (50 m).
To display the foot print map, touch the
switch.
 To delete the foot print map display
Touch the switch.
INFORMATION
 If the map or the current position is
moved to the area which is not covered by the foot print map, the screen
scale automatically changes to 150
feet (50 m).
 On the foot print map, a one way
street is displayed by .
 It is not possible to perform scrolling
on the foot print map (one−touch
scroll) while driving.
 To display building information
Information is available only for buildings for
which information is recorded on the map
disc.
1. Touch the “Info.” switch while the
foot print map is displayed.
If the map is displayed in split screen, it turned
into a single map display.
63
2. Using an eight−direction arrow, move
the cursor to the position of the building
you wish to display information.
3. Touch the “Building Info.” switch.
4. Details of POIs in some buildings may
be displayed. If you wish to see detailed
POI information, touch the building name.
You can see the detail of the selected
POIs.
64
65
ADVANCED FUNCTIONS
Descriptions of functions for more effective use
Suspending and resuming guidance 66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Volume 67. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User selection 67. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
My places 70. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Area to avoid 77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup 80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current position calibration 81. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distance unit 83. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Estimated travel time 83. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto reroute 85. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting time zone 85. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto voice guidance 86. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice guidance in all modes 87. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notifying traffic restriction 88. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intersection guidance 89. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guidance screen on freeway 90. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Street name on scroll map 91. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display of building shape 92. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen layout function ( Function) 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POI category change (Show POI Icons) 94. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete previous point 95. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map color 96. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen animation 97. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION III
66
Suspending and resuming
guidance
 To suspend guidance
You can suspend route guidance.
Push the “MENU” button to display the
“Menu” screen and touch the “Suspend
Guidance” switch.
INFORMATION
When you do not have route guidance,
the “Suspend Guidance” switch
cannot be used.
The screen will return to the current position map without route guidance.
 To resume guidance
You can resume the suspended route
guidance.
Push the “MENU” button to display the
“Menu” screen and touch the “Resume
Guidance” switch.
The screen will change to the current position map with route guidance.
67
Volume
You can use voice guidance when approaching a destination.
You can adjust the volume of the voice or turn
off voice guidance.
Push the “MENU” button to display the
“Menu” screen, and touch the “Volume”
switch.
To adjust the volume, select the desired level
by touching the appropriate number.
If you do not need voice guidance, touch the
“Off” switch.
The selected item is highlighted in green.
INFORMATION
During route guidance, the voice guidance continues even if the navigation
screen is changed to other screens.
“Adaptive Volume Control”: If you turn the
“Adaptive Volume Control” on, the volume is
turned up automatically when the vehicle
speed exceeds 50 mph (80 km/h).
To turn the “Adaptive Volume Control” system
on, touch the switch. The indicator will be
highlighted.
User selection
The system can memorize the following
settings for up to three users.
 Map direction
 Map scale
 Guidance mode
 Setup
 Volume
 Language
Push the “MENU” button to display the
“Menu” screen. Then touch the “Select
User” switch.
68
 To register
Touch the “Memorize” switch of your
desired “User number”.
The confirmation screen will appear. To
register, touch the “Yes” switch. To return to the previous screen, touch the
“No” or “Back” switch.
When you touch the switch already registered, this screen appears. To replace,
touch the “Yes” switch. To cancel the replacement, touch the “No” or “Back”
switch.
69
 To change user
Push the “MENU” button to display the
“Menu” screen. Then touch the “Select
User” switch.
Touch the “User number” switch you
wish to change.
The above message appears, then the
map screen will be displayed.
 To delete user
Touch the “Delete” switch of “User number” you wish to delete.
70
The confirmation screen appears. To delete, touch the “Yes” switch. To return to
the previous screen, touch the “No” or
“Back” switch.
My places
You can register and keep your own
memory points (like restaurants, sports facilities, etc.) and use the memory points to
input a destination.
(a) Registering memory points
1. Push the “MENU” button to display
the “Menu” screen and touch the “My
Places” switch.
71
2. Touch the “Register” switch of the
“Memory Points”.
A screen similar to the destination input
screen appears. Input the desired point in the
same way as inputting a destination. (See
page 24.)
When you finish memory point registration,
the memory point data screen will appear.
You can set the icon, attribute, name, location
and phone number.
Touch the desired switch you want to set. (For
details, see “(b) Editing memory points”.)
INFORMATION
Up to 106 memory points can be registered.
72
(b) Editing memory points
The icon, attribute, name, location and/or
telephone number of a registered memory
point can be edited.
1. Push the “MENU” button to display
the “Menu” screen and touch the “My
Places” switch.
2. Touch the “Edit” switch of the
“Memory Points”.
The screen lists the memory points.
“Date”: Touch this switch to list the memory
points in order of the registered date.
“Icon”: Touch this switch to list the memory
points in order of the icon type.
“Name”: Touch this switch to list the memory
points in alphabetical order.
“Attribute”: Touch this switch to list the
memory points in order of the home and quick
access number.
Touch the desired memory point switch to display the memory point data screen.
3. Touch the switch which you wish to
edit.
73
 To change “Icon”
Touch the desired icon.
You can turn the page by touching “Page
1”, “Page 2” or “With Sound” switch.
“With Sound”: To display sound icons.
When your vehicle approaches the memory
point, the sound which you chose will sound.
Touch the desired sound icon.
The next screen appears when you touch the
“Bell (with direction)” switch.
Touch the direction switches and adjust the
direction. Touch the “Enter” switch. The
bell sounds only when your vehicle approaches this point in the direction that you
set.
74
 To change “Attribute”
For easy destination input, set the attribute of the memory points as Home or
Quick access 1 to 5.
Touch the desired attribute. It is possible
to replace a registered attribute.
To replace the attribute, touch the “Yes”
switch. To return to the previous screen,
touch the “No” or “Back” switch.
To delete the attribute, touch the “Del.”
switch.
75
To delete an attribute, touch the “Yes”
switch. To return to the previous screen,
touch the “No” or “Back” switch.
 To change “Name”
Touch the alphabet and/or numeral keys.
When the entry has been completed, touch
the “OK” switch on the screen.
The previous screen will be displayed.
 “Show Name”
You can set the name of a memory point to
be displayed or not on the map.
To show the name, touch the “On”
switch. Not to show it, touch the “Off”
switch.
 To change “Location”
Touch the eight direction switch to move
the cursor to the desired point on the
map.
Touch the “Enter” switch and the previous
screen will be displayed.
76
 To change “Phone #” (telephone number)
Touch numeral keys.
When the entry has been completed, touch
the “OK” switch on the screen.
The previous screen will be displayed.
(c) Deleting memory points
1. Push the “MENU” button to display
the “Menu” screen and touch the “My
Places” switch.
2. Touch the “Delete” switch of the
“Memory Points”.
3. Touch the corresponding switch. To
delete all memory points, touch the “Delete All” switch.
For efficient memory point search, memory
points can be sorted by the “Date”,
“Icon”, “Name” or “Attribute” switch.
To delete, touch the “Yes” switch. To cancel
the deletion, touch the “No” switch.
77
Area to avoid
Areas you wish to avoid because of traffic
jams, construction work or other reasons
can be registered as areas to avoid.
Push the “MENU” button to display the
“Menu” screen and then touch the “My
Places” switch to display the following
screen.
INFORMATION
If a destination is inputted in the area to
avoid or the route calculation cannot be
made without running through the area
to avoid, a route passing through the
area to avoid may be shown.
(a) Registering area to avoid
1. Touch the “Register” switch of the
“Areas to avoid”.
2. Enter the location in the same way as
inputting a destination, or display the map
of the area you wish to avoid. (See page
24.)
INFORMATION
Up to 10 locations can be registered as
point/area to avoid. If there are 10 locations already registered, the message
“Unable to register additional points.
Perform operation again after deleting
unnecessary points.” appears on the
screen.
3. Set the cursor in the center of the area
to avoid, and touch the “Enter” switch.
78
4. Touch either or switch to
change the size of the area to avoid.
(b) Editing area to avoid
1. Touch the “Edit” switch of the “Areas
to Avoid” to display the “Edit Area to
Avoid” screen.
2. To edit an area to avoid, touch the corresponding switch.
3. Touch the “Name”, “Location” or
“Area Size” switch on this screen.
79
 To change “Name”
Touch alphabet or numeral keys.
When the entry has been completed, touch
the “OK” switch on the screen.
The previous screen will be displayed.
 “Show Name”
The avoid area name can be set to be displayed or not on the map. To show the
name, touch the “On” switch. Not to
show it, touch the “Off” switch.
 To change “Location”
Set the cursor to the desired location, then
touch the “Enter” switch. The previous
screen will be displayed.
 To change “Area size”
Touch either or switch to change
the size of area you want to avoid, and touch
the “OK” switch. The previous screen will
be displayed.
80
(c) Deleting area to avoid
1. Touch the “Delete” switch of the
“Areas to Avoid” to display the “Delete
Area to Avoid” screen.
2. Touch the area you wish to delete from
the list.
“Delete all”: To delete all registered areas to
avoid in the system.
3. To delete, touch the “Yes” switch. To
cancel the deletion, touch the “No”
switch.
Setup
You can set the items shown on the “Setup” screen.
1. Push the “MENU” button.
2. To display the “Setup” menu screen,
touch the “Setup” switch. Touch the
items you wish to set.
3. Touch the “OK” switch on the screen
and then the previous screen will be displayed.
“Default”: This switch initializes all of the settings.
“Calibration”: You can adjust the current vehicle position mark manually.
“Distance”: You can select “km” or “miles” as
the distance unit.
“Estimated Travel Time”: You can set the
system to display the travel time to the destination on the route guidance screen.
“Auto Reroute”: You can set the system to
automatically search for a new route to the
destination.
“Adjust Time Zone”: You can select your desired time zone.
“Auto Voice Guidance”: You can set the automatic voice guidance.
81
“Voice Guidance in All Modes”: You can set
the voice guidance in all modes.
“Notify Traffic Restriction”: You can select
notification of seasonal restrictions.
“Intersection Guidance”: You can select
ON or OFF to display intersection guidance.
“Guidance Screen on Freeway”: You can
select ON or OFF to display the guidance
screen on the freeway.
“Street Name on Scroll Map”: You can select ON or OFF to display the street name on
the scroll map.
“Display Building Shape”: You can select
ON or OFF to display the building shape on
the map screen.
“ Function”: You can set to display or
not to display each switch and current street
name on the map screen.
“Show POI Icons”: You can choose 6 icons
displayed on “Show POI Icons” top screen.
“Previous Point”: You can delete the previous destination.
“Map Color (Day)”: You can select the desired map color.
“Map Color (Night)”: You can select the desired map color.
“Screen Animation”: You can set some
screen displays to be animated.
Current position calibration
When driving, the current vehicle position
mark will be automatically corrected by
GPS signals. If GPS reception is poor due
to location, you can manually adjust the
current vehicle position mark.
1. Push the “MENU” button to display
the “Menu” screen, and then touch the
“Setup” switch.
2. Touch the “Adjust” switch of “Calibration”.
3. Touch the “Position/Direction”
switch.
INFORMATION
For additional information on the accuracy of a current vehicle position, see
“Limitations of the navigation system”
on page 10.
82
 Position/direction calibration
1. Touch the scroll arrows to move the
cursor to your desired location.
Touch the “Enter” switch.
2. Touch either the or switch to adjust the direction of the current vehicle
position mark.
Touch the “Enter” switch and the map
screen will be displayed.
 Tire change calibration
The tire change calibration function will be
used when replacing the tires. This function will adjust the mis−calculation caused
by the circumference difference between
the old tires and new ones. If this procedure is not performed when tires are replaced, the current vehicle position mark
may be incorrectly displayed.
To perform a distance calibration procedure,
touch the “Tire Change” switch on the
“Calibration” screen.
The message appears and the quick distance
calibration is automatically started. A few
seconds later, a map screen will be displayed.
83
Distance unit
1. Push the “MENU” button.
2. Touch the “Setup” switch.
3. Touch the “km” or “miles” switch of
“Distance” to choose the distance unit.
The selected switch is highlighted in green.
4. Touch the “OK” switch.
Estimated travel time
You can set the speed that is used for the
calculation of the estimated travel time.
1. Push the “MENU” button.
84
2. Touch the “Setup” switch.
3. Touch the “Set Speed” switch of the
“Estimated Travel Time”.
4. Touch or to set the average vehicle speeds for driving on a Freeway,
Main street, and Residential.
To set the default speeds, touch the “Default” switch.
5. When you finish setting the desired
speeds, touch the “OK” switch.
INFORMATION
 The displayed time to the destination
is the approximate driving time that is
calculated based on the speeds you
selected and your actual position
along the guidance route.
 The time shown on the screen may
vary greatly depending on your progress along the route, which may be affected by road conditions such as
traffic jams, construction work.
 It is possible to display up to 99 hours
59 minutes.
85
Auto reroute
When the “Auto Reroute” feature is turned
on, the system will automatically search
for a new route to the destination if you
stray from the guidance route. This feature does not operate while you are driving
on roads where guidance is not available.
To turn the “Auto Reroute” mode on:
1. Push the “MENU” button.
2. Touch the “Setup” switch.
3. Touch the “On” switch of “Auto
Reroute”.
The selected switch is highlighted in green.
INFORMATION
If your vehicle strays from the guidance
route, the system searches for a new
route to the destination. The new route
may or may not take you back to the previous route depending on how far you
are off the original guidance route.
Adjusting time zone
1. Push the “MENU” button.
2. Touch the “Setup” switch.
86
3. Touch the “Change” switch. The
“Adjust Time Zone” screen appears on the
display.
4. Touch the desired time zone.
The selected switch is highlighted in green.
5. Touch the “OK” switch on the screen
and the “Setup” screen will be displayed.
Auto voice guidance
When the “Auto Voice Guidance” feature
is turned on, the voice guidance can be
heard automatically.
When the “Auto Voice Guidance” feature
is turned off, the voice guidance can be
heard only if you push the “MAP/
VOICE” button.
To turn the “Auto Voice Guidance” mode
on:
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch to display page 2 of the
“Setup” screen.
87
3. Touch the “On” switch of “Auto Voice
Guidance”.
The selected switch is highlighted in
green.
Voice guidance in all modes
When the “Voice Guidance in All Modes”
feature is turned on, you can hear the
voice guidance in all modes.
When the “Voice Guidance in All Modes”
feature is turned off, voice guidance cannot be heard when using the audio system.
To turn the “Voice Guidance in All Modes”
on:
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch to display page 2 of the
“Setup” screen.
88
3. Touch the “On” switch of “Voice Guidance in All Modes” and touch the “OK”
switch.
Notifying traffic restriction
When the “Notify Traffic Restriction” feature is turned on, the system notifies you
of traffic or seasonal restrictions.
To turn the “Notify Traffic Restriction”
mode on:
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch to display page 2 of the
“Setup” screen.
89
3. Touch the “On” switch of “Notify Traffic Restriction” and touch the “OK”
switch.
Intersection guidance
When the “Intersection Guidance” feature
is turned on, the system will display the intersection guidance screen if you drive
with route guidance.
To turn the “Intersection Guidance” mode
on:
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch to display page 2 of the
“Setup” screen.
90
3. Touch the “On” switch of “Intersection Guidance” and touch the “OK”
switch.
Guidance screen on freeway
When the “Guidance Screen on Freeway”
feature is turned on, the system will display the lane guidance screen if you drive
on a freeway with route guidance.
To turn the “Guidance Screen on Freeway” mode on:
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch to display page 2 of the
“Setup” screen.
91
3. Touch the “On” switch of “Guidance
Screen on Freeway” and touch the “OK”
switch.
Street name on scroll map
When the “Street Name on Scroll Map”
feature is turned on, the system will display the name of a street where the cursor
is positioned on the scroll map.
To turn the “Street Name on Scroll Map”
mode on:
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch twice to display page 3 of
the “Setup” screen.
92
3. Touch the “On” switch of “Street
Name on Scroll Map” and touch the “OK”
switch.
Display of building shape
When the “Display Building Shape” feature is turned on, the system will display
the building shape on the map screen using a scale of 150 feet (50 m) to 300 feet
(100 m).
To turn the “Display Building Shape”
mode on:
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch twice to display page 3 of
the “Setup” screen.
93
3. Touch the “On” switch of “Display
Building Shape” and touch the “OK”
switch.
Screen layout function
( Function)
You can set display or hide each switch
and current street name on the map
screen.
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch twice to display page 3 of
the “Setup” screen.
3. Touch the “Change” switch of the
“ Function”.
4. Touch the switch corresponding to the
desired setting. Then touch the “OK”
switch.
94
POI category change
(Show POI Icons)
You can choose 6 icons displayed on the
“Show POI Icons” top screen, so that you
can easily set which icons to display on
the map screen.
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch twice to display page 3 of
the “Setup” screen.
3. Touch the “Change” switch of
“Show POI Icons”.
4. Touch the category switch you wish to
change.
95
5. Touch the switch corresponding to the
desired category. Then touch the “OK”
switch.
Delete previous point
You can delete your previous destination.
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch twice to display page 3 of
the “Setup” screen.
3. Touch the “Delete” switch of “Previous Point”.
96
4. Touch the switch you want to delete.
For efficient previous point search, previous points can be sorted by the “Date”
or “Name” switch.
5. To delete the point, touch the “Yes”
switch.
To cancel the deletion, touch the “No”
switch.
Map color
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch three times to display
page 4 of the “Setup” screen.
97
3. Touch the desired color for day and/or
night map and then touch the “OK”
switch to return the map screen.
Touch the “Normal” switch to return to the
default map color.
Screen animation
When the “Screen Animation” feature is
turned on, some switches and screens become animated. (e.g.: change map guidance on the map screen)
To turn the “Screen Animation” mode on:
1. Push the “MENU” button.
2. Touch the “Setup” switch. Then
touch switch three times to display
page 4 of the “Setup” screen.
3. Touch the “On” switch of “Screen
Animation” and touch the “OK” switch.
98
99
OTHER FUNCTIONS
Other functions
Maintenance information 100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calendar with memo 105. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speech command system 112. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Help screen 114. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen adjustment 114. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen setting 115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION IV
100
Maintenance information
This system informs you when to replace
certain parts or components and shows
dealer information (if registered) on the
screen. (See “Information items” on page
101.) When the navigation system begins
operating after either the information
item’s pre−set date arrives or the driving
distance reaches a pre−determined setting, the “Information” screen will be displayed. This screen will appear every time
the system is turned on until you touch the
“Do not display this message
again” switch.
To prevent this information screen from being
displayed again, touch the “Do not display this message again” switch.
1. Push the “INFO” button to display the
“Information Menu” screen. Touch the
“Maintenance” switch to display the
“Maintenance” screen.
2. Touch the desired icon and input the
conditions.
101
Notice of “Date”: You can input the next
maintenance date.
Notice of “Distance”: You can input the driving distance until the next maintenance
check.
When you touch the switch on the
“Maintenance” screen, the screen changes to
the “Personal Event” screen. Touch the keys
to input the desired name and then input conditions.
After you input the date and/or distance,
touch the “OK” switch. The screen then returns to the “Maintenance” screen.
The following switches appear.
“Delete All”: To cancel all conditions which
have been inputted.
“Reset All”: To reset the item which has satisfied a condition.
Touch the “Off” switch at the top of the
“Maintenance” screen to turn off the information screen.
When your vehicle needs to be serviced, the
icon color will change to orange.
INFORMATION
 For scheduled maintenance information, please refer to the “Owner’s
Manual Supplement/Scheduled Maintenance”.
 Depending on driving or road conditions, the actual date and distance
may differ from the stored date and
distance in the system.
Information items
Oil change
Replace oil filter
Rotate tires
Replace tires
Replace battery
Replace brake linings
Replace wiper blades
102
Replace engine coolant
Replace brake fluid
Replace ATF
Scheduled maintenance
Replace air filter
Personal event
(a) Register dealer
You can register the dealer name, staff,
location and phone number.
1. Touch the “Set Dealer” switch on
the “Maintenance” screen.
2. Enter the location of the dealer in the
same way as for destination input. (See
page 24.)
103
After you input the dealer, the screen changes
and displays the map location of the dealer.
If it is OK, touch the “Enter” switch.
The screen changes to “Edit Dealer” screen.
(See “(b) Edit dealer”.)
(b) Edit dealer
You can edit the dealer name, staff, location and phone number.
1. Touch the “Set Dealer” switch on
the “Maintenance” screen. The “Edit
Dealer” screen appears.
2. To edit, touch the corresponding
switch.
104
 To edit “Dealer” or “Contact”
To input the name, touch the alphabet, numeral and/or umlaut keys. You can input
up to 24 letters.
After inputting, touch the “OK” switch at the
bottom right of the screen. The previous
screen will be displayed.
 To edit “Location”
Set the cursor to the desired point, and
touch the “Enter” switch on the screen.
 To edit “Phone #” (telephone number)
Touch numeral keys.
After inputting, touch the “OK” switch. The
previous screen will be displayed.
105
(c) Delete dealer
1. Touch the “Delete Dealer” switch
on the screen.
2. A message will appear on the screen.
To delete, touch the “Yes” switch. To
cancel the deletion, touch the “No” or
“Back” switch.
(d) Set as destination
Touch the “Enter ” switch on the “Set
Dealer” screen. The screen changes and
displays the map location of the registered
dealer and the “Route Preference”. (See
“ — Entering destination” on page 42.)
Calendar with memo
This system informs you of a memo entry.
At the specified date, the memo information will be displayed when the navigation
system is in operation. The memo information screen will appear every time the
system is turned on. To disable this
screen, touch the “Do not display this
message again” switch.
106
To display the “Information Menu” screen,
push the “INFO” button. Then touch the
“Calendar” switch.
The current date is circled in yellow. If the current date is not displayed on the screen, touch
the “Today” switch to display the current
month calendar.
(a) Inputting a memo
1. Touch the day you want to add a memo.
2. To display the “Memo” screen, touch
the “Add Memo” switch.
107
 Memo
Touch the “Memo” switch to enter text.
Enter text using the keys. You can enter
text up to 24 letters.
After entering the text, touch the “OK”
switch at the bottom right of the screen.
 Location
Touch the “Location” switch to set location.
A screen similar to the destination input
screen appears. Input the same way as inputting a destination. (See page 24.)
You can add the memos up to 100 until
December 31, 2022.
108
The date inputted is marked as shown
above.
You can choose the desired mark and/or date
color.
 Mark color
Touch the “Mark” switch.
Touch your desired color for the mark.
 Date color
Touch the “Date” switch.
109
Touch your desired color for the date.
You can set a color of the mark and/or date
for the date you added the memo and/or
location.
To default the date color, touch the “Delete” switch on the screen. After you
choose the date and/or mark color, touch
the “OK” switch to display the previous
screen.
(b) Adding a memo
To add a memo, touch the corresponding
date.
The “Memo” screen appears on the display. Touch the “Add Memo” switch.
(See page 106 for inputting a memo.)
You can add up to 100 memos.
(c) Deleting a memo
Touch the corresponding date. Touch the
corresponding memo switch, and then
touch the “Delete” switch on the screen.
A message appears on the display. To delete, touch the “Yes” switch. To cancel
the deletion, touch the “No” switch.
110
(d) Editing a memo
To edit a memo, touch the corresponding
date, and then touch the memo you wish to
edit.
Touch the “Memo” or “Location”
switch.
(e) Memo list
1. To list the memos you added, touch the
“List” switch.
111
2. Touch the desired search condition to
list the memos. The “Memo list” is displayed on the screen.
To display the memos listed in a desired
period, touch the “Period” switch.
Touch the number keys.
After setting the period, touch the “OK”
switch. The “Memo list” screen will be displayed.
You can set a period from January 1, 2003,
through December 31, 2022, for searching.
To delete and/or edit the memo, touch the
desired memo switch.
To delete all memos, touch the “Delete
All” switch. A message appears on the
display. To delete, touch the “Yes”
switch. To cancel the deletion, touch the
“No” switch.
112
To edit: Touch the corresponding “Memo”
or “Location” switch. (See page 110 for
details.)
To delete: Touch the “Delete” switch.
(See page 109 for details.)
Speech command system
The speech command system allows you
to operate the navigation system without
your hands off the steering wheel.
1. Push the speech command switch.
A beep sounds and on screen message is
displayed with an indicator at the top left.
2. Give a command while an indicator is
shown in the display. If you want to check
the command list, touch the “Help”
switch to display the “Voice Recog. Help”
screen. (See “Help screen” on page 114.)
When you touch the “Cancel”, the previous screen returns.
If the navigation system does not respond or
the confirmation screen does not disappear,
please push the speech command switch
and try again.
If no command is given, a beep sounds and
the indicator disappears 6 seconds later.
If the system does not recognize your
speech, the system will respond with this
message (“System does not recognize this
command, please rephrase your command.”). Start the operation from the beginning.
113
 Microphone
It is unnecessary to speak directly into the
microphone when giving a command.
Speech command example: Searching for
a route to your home.
1. Push the speech command switch.
2. Say “Home”.
If your home is not registered, you will hear
“Home is not registered”.
3. If the system recognized the command,
the recognition result “Home” is displayed on the top of the screen with the
screen message. (Displayed message
and the switches on the screen depend on
the situation.)
Touch or say “Cancel”, and the system will be
canceled. Touch or say “Help”, and displays
the “Voice Recog. Help” screen.
4. Touch “Enter” or say “Enter destination”, and the system starts searching for
a route to your home. (If the destination is
already registered, “Add” or “Replace” is
displayed on the screen.)
Touch or say “Cancel”, and the search will be
canceled.
INFORMATION
In the following conditions, the system
may not recognize the command properly.
 The command is not correct or clear.
 There are some noises such as wind
noise, etc.
114
Help screen
This system has a function which displays
the “Voice Recog. Help” screen. You can
see the command list and operation guide
on it.
 Command List
1. Touch the “Command List” switch
on the upper side of the screen and the
switches on the right side of the screen to
select the desired category.
2. You can scroll through the list of the
command list by touching “ ” or “ ”
switch.
Touch the “OK” switch after you check it.
 Operation Guide
1. Touch the “Operation Guide”
switch on the upper side of the screen and
the switches on the right side of the screen
to select the desired category.
2. You can scroll through the list of the operation guide by touching “ ” or “ ”
switch.
Touch the “OK” switch after you check it.
Screen adjustment
The brightness or contrast of the screen
can be adjusted depending on the brightness of your surroundings. You can also
turn the display off.
To display the “Display” screen push the
“DISPLAY” button.
Contrast and brightness adjustment
“CONTRAST” “+”:
Strengthens the contrast of the screen.
“CONTRAST” “−”:
Weakens the contrast of the screen.
“BRIGHTNESS” “+”:
Brightens the screen.
“BRIGHTNESS” “−”:
Darkens the screen.
After adjusting the screen, touch the
“OK” switch.
115
The screen goes off when you touch the
“SCREEN OFF” switch. To turn the display screen back on, push any button such as
“INFO”, etc. The selected screen appears.
INFORMATION
When you do not touch any switch on
the screen for 20 seconds the “Display”
screen goes off.
Depending on the position of the headlight
switch, the screen changes to either day
mode or night mode.
To display the screen in the day mode even
with the headlight switch on, touch the “DAY
MODE” switch on the adjustment screen for
brightness and contrast control.
If the screen is set in the day mode with the
headlight switch turned on, this condition is
memorized in the system even with the engine turned off.
Screen setting
1. Push the “INFO” button to display the
“Information Menu” screen.
2. Touch the “Screen Setting” switch.
116
(a) Automatic transition
You can select a function that enables automatic return to the navigation screen
from the audio screen.
Select “ON” or “OFF” and then touch
the “OK” switch.
“ON”: The navigation screen automatically
returns from the audio screen 20
seconds after the end of audio operation.
“OFF”: The audio screen remains on.
(b) Background color
You can select a background color.
Select the desired background color and
then touch the “OK” switch.
117
AUDIO SYSTEM
Audio system
Quick reference 118. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using your audio system 119. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio system operating hints 137. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
V
SECTION V
118
1 Function switch display screen
Touch the switches displayed on the
screen to control the radio and CD
player. For details, see page 120.
2 “TUNE” knob
Turn this knob to move up or down the
station band. For details, see pages 122
and 126.
3 “AM·SAT” button
Push this button to choose either an AM
or SAT station. For details, see pages
120, 122 and 126.
4 “FM” button
Push this button to choose an FM station. For details, see pages 120 and
122.
5 “DISC” button
Push this button to turn the CD player
on. For details, see pages 120 and 132.
6 “SCAN” button
Push this button to scan radio stations or
scan the tracks on a CD. For details, see
pages 123, 128 and 134.
7 “OPEN” button
Push this button to open the display to
access the slot for the CD player. For
details, see page 131.
Quick reference
119
8 “AUDIO” button
Push this button to display the audio
control screen. For details, see page
120.
9 “SEEK/TRACK” button
Push either side of this button to seek up
or down for a station, or to access a desired program or track. For details, see
pages 123, 128 and 133.
10 “PWR·VOL” knob
Push this knob to turn the audio system
on and off, and turn it to adjust the volume. For details, see page 120.
Using your audio system —
— Some basics
This section describes some of the basic features of your audio system. Some information
may not pertain to your system.
Your audio system works when the ignition
switch is in the “ACC” or “ON” position.
NOTICE
To prevent the battery from being discharged, do not leave the audio system
on longer than necessary when the engine is not running.
By pushing the switch above, you can operate the speech command system.
For the operation of the speech command
system and the command, see pages 112
and 114. V
120
(a) Turning the system on and off
“PWR·VOL”: Push this knob to turn the audio
system on and off. Turn this knob to adjust the
volume. The system turns on in the last mode
used.
“AUDIO”: Push this button to display
switches for audio system (audio control
mode).
You can select the function that enables automatic return to the previous screen from the
audio screen. See page 115 for details.
Push “AM·SAT”, “FM” or “DISC” button to
turn on the desired mode. The selected
mode turns on immediately.
Push these buttons if you want to switch from
one mode to another.
If the CD is not set, the CD player does not
turn on.
You can turn off the CD player by ejecting the
CD. If the audio system was previously off,
then the entire audio system will be turned off
when you eject the CD. If the other function
was previously playing, it will come on again.
121
The switches for radio and CD player operation are displayed on the function
switch display screen when the audio
control mode is selected. Touch them
lightly and directly on the screen.
The selected switch is highlighted in green or
yellow.
INFORMATION
 If the system does not respond to a
touch of a switch, move your finger
away from the screen and then touch
it again.
 You cannot operate dimmed
switches.
 Wipe off fingerprints on the surface of
the display using a glass cleaning
cloth.
(b) Automatic sound levelizer (ASL)
When the audio sound becomes difficult to be
heard due to road noise, wind noise,etc. during driving, the system adjusts to the optimum
volume according to the noise level. To turn
this function on, touch the “ASL” on the audio
control screen.
(c) Tone and balance
How good an audio program sounds to you is
largely determined by the mix of the treble,
midrange, and bass levels. In fact, different
kinds of music and vocal programs usually
sound better with different mixes of treble,
mid−range, and bass.
A good balance of the left and right stereo
channels and of the front and rear sound levels is also important.
Keep in mind that if you are listening to a stereo recording or broadcast, changing the
right/left balance will increase the volume of
one group of sounds while decreasing the volume of another.
Touching the “SOUND” switch displayed
on the screen at the audio control mode
will display the sound control mode. Adjust the tone and balance as follows.
To adjust the tone, touch the “+” or “−”
switch on the screen. To adjust the balance between the front and rear speakers,
touch the “FRONT” or “REAR” switch on
the screen, and to adjust the balance between the left and right, touch the “L” or
“R” switch on the screen.
“BASS”: Adjusts low−pitched tones.
“MID”: Adjusts mid−pitched tones.
“TREB”: Adjusts high−pitched tones.
As the yellow display goes up, each tone is
more emphasized.
V
122
(d) Your CD player
When you insert a CD, insert it with the label
side up. The CD player will play from track 1
through to the end of the CD. Then it will play
from track 1 again.
NOTICE
Never try to disassemble or oil any part
of the CD player. Do not insert anything
except a CD into the slot.
The player is intended for use with 12 cm (4.7
in.) CDs only.
— Radio operation
(a) Listening to the radio
Push these buttons to choose either an
AM or FM station.
“AM”, “FM1” or “FM2” appears on the screen.
If your vehicle is equipped with a satellite
radio broadcast system, when you push
the “AM·SAT” button, “AM”, “SAT1”, “SAT2”
or “SAT3” station appears on the display. For
details about satellite radio broadcast, see
“— Radio operation (XM satellite radio broadcast)” on page 125.
Turn the knob clockwise to step up the station band or counterclockwise to step
down.
Your radio automatically changes to stereo
reception when a stereo broadcast is received. “ST” appears on the screen. If the
signal becomes weak, the radio reduces the
amount of channel separation to prevent the
weak signal from creating noise. If the signal
becomes extremely weak, the radio switches
from stereo to mono reception. In this case,
“ST” disappears from the screen.
123
(b) Presetting a station
1. Tune in the desired station.
2. Touch one of the switches (1 — 6) you
want and hold it until a beep is heard. This
sets the station to the switch and the frequency appears on the switch.
Each radio mode (AM, FM1 or FM2) can store
up to 6 stations. To change the preset station
to a different one, follow the same procedure.
The preset station memory is cancelled when
the power source is interrupted by battery disconnection or a blown fuse.
(c) Selecting a station
Tune in the desired station using one of the
following methods.
Preset tuning: Touch the switch (1 — 6) for
the station you want. The switch is highlighted in green and the station frequency appears on the screen.
Seek tuning: Push the “SEEK/TRACK” button on either side. The radio will begin seeking up or down for a station of the nearest frequency and will stop on reception. Each time
you push the button, the stations will be
searched automatically one after another.
To scan all the frequencies: Touch the
“SCAN” switch on the screen or push the
“SCAN” button briefly. “SCAN” appears on
the screen. The radio will find the next station
and stay there for a few seconds, and then
scan again. To select a station, touch the
“SCAN” switch or push the “SCAN” button
again.
To scan the preset stations: Touch the
“SCAN” switch on the screen or push the
“SCAN” button for longer than approximately
a second. “P. SCAN” appears on the screen.
The radio will tune in the next preset station,
stay there for a few seconds, and then move
to the next preset station. To select a station,
touch the “SCAN” switch or push the “SCAN”
button again.
(d) Radio Data System
Your audio system is equipped with Radio
Data Systems (RDS). RDS mode allows you
to receive text messages from radio stations
that utilize RDS transmitters.
When RDS is on, the radio can
— only select stations of a particular program
type,
— display messages from radio stations,
— search for a stronger signal station.
RDS features are available for use only on FM
stations which broadcast RDS information.
V
124
“TYPE  ” switch
If the system receives no RDS stations, “NO
PTY” appears on the display.
Each time you touch the “TYPE ” or “TYPE
” switch, the program type changes as follows:
 ROCK
 MISC (Miscellaneous)
 Inform (Information)
 Easy Lis (Easy listening)
 Cls/Jazz (Classical music and Jazz)
 R & B (Rhythm and Blues)
 Religion
 Alert (Emergency message)
“TYPE SEEK” switch
When a program is set, “TYPE SEEK” switch
appears. Touch the switch and the system
starts to seek the station in the relevant program type.
If any type program station is not found,
“NOTHING” appears on the display.
“MSG” (MESSAGE) switch
If the system receives a radio text from an
RDS station, “MSG” appears on the display.
Touch the “MSG” switch, and a text message
is displayed on the screen.
In case a text message is not accepted in a
screen, you can touch the “MSG” switch and
hold it to display the rest of the message.
When the system can show the station name,
“RDS” appears on the display. Each time you
touch the “MSG” switch, indication on the display changes from the band to the station
name, to radio text in this order. After six seconds pass, indication returns to the band.
125
(e) Traffic announcement
“TRAF” switch
A station that regularly broadcasts traffic information is automatically located.
When you push the “TRAF” switch, “TRAF
SEEK” appears on the display and the radio
will start seeking any traffic program station.
If no traffic program station is found, “NOTHING” appears on the display.
If a traffic program station is found, the name
for traffic program station is displayed and
“TRAF” is lit for a while until a traffic announcement is received.
— Radio operation
(XM satellite radio broadcast)
To listen to a satellite radio broadcast in your
vehicle, an additional genuine Toyota satellite
receiver and antenna must be purchased and
installed, and the subscription to the XM satellite radio is necessary.
(a) How to subscribe to an XM satellite
radio
An XM satellite radio is a tuner designed exclusively to receive broadcasts provided under a separate subscription. Availability is
limited to the 48 contiguous states.
How to subscribe: You must enter into a
separate service agreement with the XM radio in order to receive satellite broadcast programming in the vehicle. Additional activation
and service subscription fees apply that are
not included in the purchase price of the vehicle and optional digital satellite tuner. For
complete information on subscription rates
and terms, or to subscribe to the XM radio,
visit XM on the web at www.xmradio.com or
call an XM’s Listener Care at (800) 852−9696.
The XM radio is solely responsible for the
quality, availability and content of the satellite
radio services provided, which are subject to
the terms and conditions of the XM radio customer service agreement.
Customers should have their radio ID ready;
the radio ID can be found by selecting “channel 000” on the radio. For details, see the
“Displaying the radio ID” that follows.
All fees and programming are the responsibility of the XM satellite radio and are subject to
change.
V
126
Satellite tuner technology notice:
Toyota’s satellite radio tuners are awarded
Type Approval Certificates from XM Satellite
Radio Inc. on “May 7, 2004” as proof of compatibility with the services offered by the XM
satellite radio.
(b) Displaying the radio ID
Each XM tuner is identified with a unique radio ID. You will need the radio ID when activating XM service or when reporting a problem.
If you select the “CH 000” using the “TUNE”
knob, the ID code of 8 alphanumeric characters appears. If you select another channel,
display of the ID code is canceled. The channel (000) alternates the display between the
radio ID and the specific radio ID code.
(c) Listening to satellite radio
Push the “AM·SAT” button to choose an
SAT channel.
Besides “AM”, “SAT1”, “SAT2” or “SAT3” also
appears on the display.
127
Turn this knob to select the next or previous channel.
If you turn continuously, you can rapidly scroll
forward or down through the channels.
(d) Channel category
When the channel category appears, touch
either “TYPE” or “TYPE” switch to go to
the next or previous category.
(e) Presetting a channel
1. Tune in the desired channel.
2. Touch one of the channel selector
switches (1 — 6) and hold it until a beep is
heard. This sets the channel to the switch
and the name and number of the channel
appears on the switch.
Each switch can store three SAT channels.
To change the preset channel to a different
one, follow the same procedure.
The preset channel memory is cancelled
when the power source is interrupted by battery disconnection or a blown fuse.
V
128
(f) Selecting a channel
Tune in the desired channel using one of the
following methods.
Preset tuning: Touch the switch (1 — 6) for
the channel you want. The switch (1 — 6) is
highlighted in green and channel number appears on the display.
To select channel within the current category: Push the “” or “” button of the
“SEEK/TRACK” button.
To scan the currently selected channel
category: Touch the “TYPE SCAN” switch or
push the “SCAN” button briefly. “SCAN” appears on the display. The radio will find the
next channel in the same channel category,
stay there for a few seconds, and then scan
again. To select a channel, touch the “TYPE
SCAN” switch or push the “SCAN” button a
second time.
To scan the preset channels: Push the
“SCAN” button and hold it until you hear a
beep. “P.SCAN” appears on the display. The
radio will find the next preset channel, stay
there for a few seconds, and then move to the
next preset channel. To select a channel,
push the “SCAN” button a second time.
(g) Displaying the title and name
When you touch the “TEXT” switch, the song/
program title and the artist name/feature are
displayed.
Up to 10 alphanumeric characters can be displayed. (Some information will not be fully
displayed.)
When you touch the “TEXT” switch again, the
display returns.
129
(h) If the satellite radio tuner malfunctions
When problems occur with the XM tuner, a message will appear on the display. Referring to the table below to identify the problem, take the
suggested corrective action.
ANTENNA
The XM antenna is not connected. Check whether the XM antenna cable is attached securely.
A short−circuit occurs in the antenna or the surrounding antenna cable. See a Lexus certified dealer.
UPDATING
You have not subscribed to the XM satellite radio. The radio is being updated with the latest encryption code.
Contact the XM satellite radio for subscription information. When a contact is canceled, you can choose the
“CH000” and all free−to−air channels.
The premium channel you selected is not authorized. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel. If you want to listen to the
premium channel, contact the XM satellite radio.
NO SIGNAL The XM signal is too weak at the current location. Wait until your vehicle reaches a location with a stronger signal.
LOADING The unit is acquiring audio or program information. Wait until the unit has received the information.
OFF AIR The channel you selected is not broadcasting any programming. Select another channel.
−−−−− There is no song/program title or artist name/feature associated with the channel at that time. No action needed.
−−−
The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the previous
channel or “CH001”. If it does not change automatically, select another channel.
The XM Listener Care Center is also available on the phone, please call (800) 852−9696 during the following hours:
Monday — Saturday: 7 a.m. — 1 a.m. Sunday: 12 p.m. — 12 a.m. (EST)
V
130
NOTICE
This equipment has been tested and
found to comply with the limits for a
class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
— Consult the dealer or an experienced
radio/TV technician for help.
Information to user
Alternation or modifications carried out
without appropriate authorization may
invalidate the user’s right to operate the
equipment.
INFORMATION
This XM tuner supports “Audio Services” (Music and Talk) of only XM satellite radio and “Text Information”* linked
to the respective “Audio Services”.
*Text Information includes, Station
Name, (Artist) Name, (Song) Title and
Category Name.
131
— CD player operation (a) Playing a CD
The slot for the CD player is behind the
display.
To insert a CD, push the “OPEN” button to
lower the display. Put the CD in the slot
with the label side up.
The player will automatically start when you
insert the CD. At this time, “CD” appears on
the screen.
If the label faces down, the CD cannot be
played. In this case, “CD CHECK” appears
on the screen.
CAUTION
 Do not place anything on the opened
display, as such items may be thrown
about in the compartment and possibly injure people in the vehicle during
sudden braking or in an accident.
 To reduce the chance of injury in case
of an accident or sudden stop while
driving, keep the display closed.
 Take care not to jam your hand while
the display is moving. Otherwise, you
could be injured.
NOTICE
Do not obstruct the display while it is
moving. It could damage your audio
system.
INFORMATION
Under extremely cold conditions, the
display may react slowly or operation
sound may become louder.
V
132
To stop and eject the CD, push the “OPEN”
button to lower the display. Push the “DISC
” button.
Push the “DISC” button if a CD is already
loaded in the slot.
“CD” appears on the screen.
133
With CD changer—
Push the “DISC” button twice if the magazine is already loaded in the player.
“CD CHANGER” appears on the screen.
The CDs set in the magazine are played continuously. The number of the currently−playing CD, the track number and the time from
the beginning of the program are shown on
the screen.
When play of one CD ends, the first track of
the following CD starts. When play of the final
CD ends, play of the first CD starts again.
The player will skip any empty CD trays.
Pushing the “DISC” button while playing a CD
in the CD changer will switch from the CD in
the changer to the CD in the CD player.
If you push the “DISC” button when the
source is other than the CD, a CD in the CD
player or CD changer, whichever was previously used, will play.
(b) Selecting a desired CD (with CD
changer)
Touch the desired CD number on the
screen.
The selected CD number is highlighted in
green.
The player will start playing the selected CD
from the first track.
(c) Searching for a desired CD (with CD
changer)
Touch the “DISC SCAN” switch.
With “DISC SCAN” highlighted in yellow , the
program at the beginning of each CD will be
played for 10 seconds. To continue listening
to the program of your choice, touch the
“DISC SCAN” switch a second time.
After all the tracks are scanned in one pass,
normal play resumes.
(d) Selecting a desired track
“SEEK/TRACK” button: Use for a direct access to a desired track.
Push either side of the “SEEK/TRACK” button and hold it until the desired track number
appears on the screen. As you release the
button, the player will start playing the selected track from the beginning.
Fast forward: Touch the switch and
hold it to fast forward the CD. When you release the switch, the CD player will resume
playing from that position.
Reverse: Touch the switch and hold
it to reverse the CD. When you release the
switch, the CD player will resume playing.
V
134
(e) Searching for a desired track
Touch the “SCAN” switch on the screen or
push the “SCAN” button.
The CD player will play the next track for 10
seconds, then scan again. To select a track,
touch the “SCAN” switch on the screen or
push the “SCAN” button a second time. If the
player reaches the end of the CD, it will continue scanning at track 1.
After all the tracks are scanned in one pass,
normal play resumes.
(f) Other CD player functions
“RPT” switch: Use it for automatic repeat of
the track you are currently listening to.
Touch the switch while the track is playing.
When the track is finished, the player will automatically go back to the beginning of the
track and play the track again. To cancel it,
touch the switch once again.
“DISC RPT” switch (with CD changer):
Use it for automatic repeat of the CD you are
currently listening to.
Touch the switch while the CD is playing.
When the CD is finished, the player will automatically go back to the beginning of the CD
and play the CD again. To cancel it, touch the
button once again.
“RAND” switch: Use it for automatic and
random selection.
When the switch is touched, the system selects a track in the CD. To cancel it, touch the
switch once again.
“DISC RAND” switch (with CD changer):
Use it for automatic track selection for all the
CDs and play by the system.
When the switch is touched, the system selects a track in the CDs of all the magazines
which are set and plays it. To cancel it, touch
the switch once again.
When a track is skipped or the system is inoperative, touch the switch to reset.
If a CD−TEXT disc is inserted, the title of the
CD and track will be displayed. Up to 29 letters can be displayed.
With CD changer —
To display the title of the CD and truck, touch
the “TITLE” switch. When the “TITLE OFF”
switch is touched, the display changes to the
CD number screen.
135
(g) Inserting CDs (with CD changer)
1. Pull up the lock release lever and raise
the lid of the console box.
2. Slide open the cover of the CD changer.
3. Push this button to eject the magazine.
V
136
4. Pull out the tray while pushing the lock
release button.
5. Put a CD on the tray with its label face
up and push the tray back into the magazine.
If the label faces down, the CD cannot be
played. In this case, “CD X (CD number) error” appears on the screen.
6. Insert the magazine into the player as
indicated by the arrow head on the magazine and close the door and console box.
When the magazine is set completely, the
system will be in a load cycle for approximately 20 seconds while the system searches for
CDs in the magazine. Upon completion of
this cycle, the CD unit will be ready to play. If
the “DISC” button is pushed during the load
cycle, “CD SEEK” appears on the screen until
the system completes the load cycle. Then
the system will begin normal play.
137
CAUTION
To reduce the chance of injury in case of
an accident or a sudden stop, always
keep the console box closed while
driving.
(h) If the player malfunctions
If “CD ERROR” appears on the screen, audio
signals of the CD cannot be read or the system has trouble. Push the “DISC” button once
again.
If the player does not operate, check that the
CD surface is not soiled or damaged. If the
CD is O.K., the following causes are possible.
 The temperature of the player’s internal
mechanism may be raised because of
high external temperature. Remove the
CD from the player to cool it.
With CD changer—
 Condensation may have occurred on the
internal mechanism of the automatic
changer. Open the cover to let the air circulate.
 The temperature of the player’s internal
mechanism may be raised because of
high external temperature. Remove the
magazine from the player to cool it.
If the player still does not operate, have it
checked by your dealer.
Audio system operating hints
NOTICE
To ensure correct audio system operations:
 Be careful not to spill beverages over
the audio system.
 Do not put anything other than a CD
into the slot.
 The use of a cellular phone inside or
near the vehicle may cause a noise
from the speakers of the audio system which you are listening to. However, this does not indicate a malfunction.
RADIO RECEPTION
Usually, a problem with radio reception does
not mean there is a problem with your radio —
it is just the normal result of conditions outside
the vehicle.
V
138
For example, nearby buildings and terrain
can interfere with FM reception. Power lines
or telephone wires can interfere with AM signals. And of course, radio signals have a limited range. The farther you are from a station,
the weaker its signal will be. In addition, reception conditions change constantly as your
vehicle moves.
Here are some common reception problems
that probably do not indicate a problem with
your radio:
FM
Fading and drifting stations — Generally, the
effective range of FM is about 40 km (25
miles). Once outside this range, you may notice fading and drifting, which increase with
the distance from the radio transmitter. They
are often accompanied by distortion.
Multi−path — FM signals are reflective, making it possible for two signals to reach your antenna at the same time. If this happens, the
signals will cancel each other out, causing a
momentary flutter or loss of reception.
Static and fluttering — These occur when signals are blocked by buildings, trees, or other
large objects. Increasing the bass level may
reduce static and fluttering.
Station swapping — If the FM signal you are
listening to is interrupted or weakened, and
there is another strong station nearby on the
FM band, your radio may tune in the second
station until the original signal can be picked
up again.
AM
Fading — AM broadcasts are reflected by the
upper atmosphere — especially at night.
These reflected signals can interfere with
those received directly from the radio station,
causing the radio station to sound alternately
strong and weak.
Station interference — When a reflected signal and a signal received directly from a radio
station are very nearly the same frequency,
they can interfere with each other, making it
difficult to hear the broadcast.
Static — AM is easily affected by external
sources of electrical noise, such as high tension power lines, lightening, or electrical motors. This results in static.
CARING FOR YOUR CD PLAYER AND
CD’S
 Your CD player is intended for use with 12
cm (4.7 in.) CDs only.
 Extremely high temperatures can keep
your CD player from working. On hot
days, use the air conditioning to cool the
vehicle interior before you listen to a CD.
 Bumpy roads or other vibrations may
make your CD player skip.
 If moisture gets into your CD player, you
may not hear any sound even though your
CD player appears to be working. Remove the CD from the player and wait until
it dries.
CAUTION
CD players use an invisible laser beam
which could cause hazardous radiation exposure if directed outside the
unit. Be sure to operate the player
correctly.
139
 Use only CDs marked as shown above.
The following products may not be playable on your CD player.
Copy−protected CDs
CD−Rs (CD−Recordable)
CD−RWs (CD−Re−writable)
CD−ROMs
 Special shaped CDs
 Transparent/translucent CDs
 Low quality CDs
 Labeled CDs
V
140
NOTICE
Do not use special shaped, transparent/
translucent, low quality or labeled CDs
such as those shown in the illustrations.
The use of such CDs may damage the
player or changer, or it may be impossible to eject the CD.
 Correct  Wrong
 Handle CDs carefully, especially when
you are inserting them. Hold them on the
edge and do not bend them. Avoid getting
fingerprints on them, particularly on the
shiny side.
 Dirt, scratches, warping, pin holes, or other CD damage could cause the player to
skip or to repeat a section of a track. (To
see a pin hole, hold the CD up to the light.)
 Remove CDs from the CD player when
you are not listening to them. Store them
in their plastic cases away from moisture,
heat, and direct sunlight.
To clean a CD: Wipe it with a soft, lint−free
cloth that has been dampened with water.
Wipe in a straight line from the center to the
edge of the CD (not in circles). Dry it with
another soft, lint−free cloth. Do not use a conventional record cleaner or anti−static device.

PDF Document reader online

This website is focused on providing document in readable format, online without need to install any type of software on your computer. If you are using thin client, or are not allowed to install document reader of particular type, this application may come in hand for you. Simply upload your document, and Docureader.top will transform it into readable format in a few seconds. Why choose Docureader.top?

  1. Unlimited sharing - you can upload document of any size. If we are able to convert it into readable format, you have it here - saved for later or immediate reading
  2. Cross-platform - no compromised when reading your document. We support most of modern browers without the need of installing any of external plugins. If your device can oper a browser - then you can read any document on it
  3. Simple uploading - no need to register. Just enter your email, title of document and select the file, we do the rest. Once the document is ready for you, you will receive automatic email from us.

Previous 10

Next 10