KX25/KX49/KX61 Owner's Manual - Keyfax

Copy and paste this link to your website, so they can see this document directly without any plugins.



Keywords

MIDI, button, this, Bass, Yamaha, GtPl, Cubase, that, using, Arpeggio, with, When, DrPc, Control, SOFTWARE, buttons, This, from, VSTi, power, will, your, computer, software, Manual, NOTE, display, Tel:, select, other

Transcript

KX25/KX49/KX61 Owner's Manual
Cover(dummy)
2007/07/12
v010
SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any
power supply or adapter other than one described in the
manual, on the name plate, or specifically recommended by Yamaha.
WARNING: Do not place this product in a position
where anyone could walk on, trip over, or roll anything
over power or connecting cords of any kind. The use of
an extension cord is not recommended! If you must use
an extension cord, the minimum wire size for a 25’ cord
(or less) is 18 AWG. NOTE: The smaller the AWG number, the larger the current handling capacity. For longer
extension cords, consult a local electrician.
This product should be used only with the components
supplied or; a cart, rack, or stand that is recommended
by Yamaha. If a cart, etc., is used, please observe all
safety markings and instructions that accompany the
accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to
be correct at the time of printing. However, Yamaha
reserves the right to change or modify any of the specifications without notice or obligation to update existing
units.
This product, either alone or in combination with an
amplifier and headphones or speaker/s, may be capable
of producing sound levels that could cause permanent
hearing loss. DO NOT operate for long periods of time
at a high volume level or at a level that is uncomfortable.
If you experience any hearing loss or ringing in the ears,
you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time
period before damage occurs.
Some Yamaha products may have benches and / or
accessory mounting fixtures that are either supplied
with the product or as optional accessories. Some of
these items are designed to be dealer assembled or
installed. Please make sure that benches are stable and
any optional fixtures (where applicable) are well secured
BEFORE using.
Benches supplied by Yamaha are designed for seating
only. No other uses are recommended.
NOTICE:
Service charges incurred due to a lack of knowledge
relating to how a function or effect works (when the unit
is operating as designed) are not covered by the manufacturer’s warranty, and are therefore the owners
responsibility. Please study this manual carefully and
consult your dealer before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user
safe and environmentally friendly. We sincerely believe
that our products and the production methods used to
produce them, meet these goals. In keeping with both
the letter and the spirit of the law, we want you to be
aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable
battery which (if applicable) is soldered in place. The
average life span of this type of battery is approximately
five years. When replacement becomes necessary, contact a qualified service representative to perform the
replacement.
This product may also use “household” type batteries.
Some of these may be rechargeable. Make sure that the
battery being charged is a rechargeable type and that
the charger is intended for the battery being charged.
When installing batteries, do not mix batteries with new,
or with batteries of a different type. Batteries MUST be
installed correctly. Mismatches or incorrect installation
may result in overheating and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of
used batteries promptly and as regulated by the laws in
your area. Note: Check with any retailer of household
type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or
for some reason its useful life is considered to be at an
end, please observe all local, state, and federal regulations that relate to the disposal of products that contain
lead, batteries, plastics, etc. If your dealer is unable to
assist you, please contact Yamaha directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the product.
The model number, serial number, power requirements,
etc., are located on this plate. You should record the
model number, serial number, and the date of purchase
in the spaces provided below and retain this manual as
a permanent record of your purchase.
Model
Serial No.
Purchase DatePLEASE KEEP THIS MANUAL
92-BP (bottom)
1. IMPORTANT NOTICE: DO NOT MODIFY does not guarantee that interference will not occur
FCC INFORMATION (U.S.A.)THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the
USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies
and, if not installed and used according to the
instructions found in the users manual, may cause
interference harmful to the operation of other electronic devices. Compliance with FCC regulations in all installations. If this product is found to be the
source of interference, which can be determined by
turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is
being affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to co-axial type
cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you
can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic
Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha Corporation of America
or its subsidiaries.* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)OBSERVERA!
Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den ar ansluten till vägguttaget, även om själva apparaten har stängts av.
ADVARSEL: Netspæendingen til dette apparat er IKKE afbrudt, sålæenge netledningen
siddr i en stikkontakt, som er t endt — også selvom der or slukket på apparatets afbryder.
VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta.(standby)COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Electronic Keyboard
Model Name : KX25/KX49/KX61
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference
that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.(FCC DoC)
4
(3)-11
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death
from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but
are not limited to, the following:
• Only use the voltage specified as correct for the instrument. The
required voltage is printed on the name plate of the instrument.
• Use the specified adaptor (PA-3C, PA-130 or an equivalent
recommended by Yamaha) only. Using the wrong adaptor can result
in damage to the instrument or overheating.
• Check the electric plug periodically and remove any dirt or dust
which may have accumulated on it.
• Do not place the AC adaptor cord near heat sources such as heaters
or radiators, and do not excessively bend or otherwise damage the
cord, place heavy objects on it, or place it in a position where anyone
could walk on, trip over, or roll anything over it.
• Do not open the instrument or attempt to disassemble the internal
parts or modify them in any way. The instrument contains no userserviceable parts. If it should appear to be malfunctioning,
discontinue use immediately and have it inspected by qualified
Yamaha service personnel.
• Do not expose the instrument to rain, use it near water or in damp or
wet conditions, or place containers on it containing liquids which
might spill into any openings. If any liquid such as water seeps into
the instrument, turn off the power immediately and unplug the power
cord from the AC outlet. Then have the instrument inspected by
qualified Yamaha service personnel.
• Never insert or remove an electric plug with wet hands.
• Do not put burning items, such as candles, on the unit.
A burning item may fall over and cause a fire.
• If the AC adaptor cord, plug or USB cable becomes frayed or
damaged, or if there is a sudden loss of sound during use of the
instrument, or if any unusual smells or smoke should appear to be
caused by it, immediately turn off the power switch, disconnect the
adaptor plug from the outlet, disconnect the USB cable and have the
instrument inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or
others, or damage to the instrument or other property. These precautions include, but are not limited
to, the following:
• When removing the electric plug from the instrument or an outlet,
always hold the plug itself and not the cord.
• Unplug the AC power adaptor when not using the instrument, or
during electrical storms.
• Do not connect the instrument to an electrical outlet using a
multiple-connector. Doing so can result in lower sound quality, or
possibly cause overheating in the outlet.
• Do not expose the instrument to excessive dust or vibrations, or
extreme cold or heat (such as in direct sunlight, near a heater, or in a
car during the day) to prevent the possibility of panel disfiguration or
damage to the internal components.
• Do not use the instrument in the vicinity of a TV, radio, stereo
equipment, mobile phone, or other electric devices. Otherwise, the
instrument, TV, or radio may generate noise.
• Do not place the instrument in an unstable position where it might
accidentally fall over.
• Before moving the instrument, remove all connected adaptor and
other cables.
Power supply/AC power adaptor
Do not open
Water warning
Fire warning
If you notice any abnormality
Power supply/AC power adaptor LocationOwner’s Manual
(3)-11
• When setting up the product, make sure that the AC outlet you are
using is easily accessible. If some trouble or malfunction occurs,
immediately turn off the power switch and disconnect the plug from
the outlet. Even when the power switch is turned off, electricity is still
flowing to the product at the minimum level. When you are not using
the product for a long time, make sure to unplug the power cord from
the wall AC outlet.
• Before connecting the instrument to other electronic components,
turn off the power for all components. Before turning the power on or
off for all components, set all volume levels to minimum. Also, be
sure to set the volumes of all components at their minimum levels
and gradually raise the volume controls while playing the instrument
to set the desired listening level.
• When cleaning the instrument, use a soft, dry cloth. Do not use paint
thinners, solvents, cleaning fluids, or chemical-impregnated wiping
cloths.
• Do not insert a finger or hand in any gaps on the instrument.
• Never insert or drop paper, metallic, or other objects into the gaps on
the panel or keyboard. If this happens, turn off the power
immediately and unplug the power cord from the AC outlet. Then
have the instrument inspected by qualified Yamaha service
personnel.
• Do not place vinyl, plastic or rubber objects on the instrument, since
this might discolor the panel or keyboard.
• Do not rest your weight on, or place heavy objects on the instrument,
and do not use excessive force on the buttons, switches or
connectors.
• Do not use the instrument/device or headphones for a long period of
time at a high or uncomfortable volume level, since this can cause
permanent hearing loss. If you experience any hearing loss or
ringing in the ears, consult a physician.
Saving and backing up the created Control
Template
• The Control Template created by using a computer or via the panel
operation of the KX will be stored on internal memory of the KX.
Stored data may be lost due to malfunction or incorrect operation.
Save important data to a computer by using the special Editor
software “KX Editor” (page 6).
Always turn the power off when the instrument is not in use.
Even when the power switch is in the “STANDBY” position, electricity is still flowing to the instrument at the minimum level. When you are not using the
instrument for a long time, make sure you unplug the AC power adaptor from the wall AC outlet.
SPECIAL NOTICES
• The USB-MIDI Driver, Extensions for Steinberg DAW, the corresponding manuals and the copryrights under exclusive ownership by Yamaha Corporation.
• The software included in the Cubase AI4 DVD-ROM and the copyrights thereof are under exclusive ownership by Steinberg Media Technologies GmbH.
Note that Yamaha does not offer technical support for the DAW software in the DVD-ROM.
• The VSTi tools included in the “VSTi” folder of the TOOLS for KX DVD-ROM and the copyrights thereof are under exclusive ownership by the respective
companies. Note that Yamaha does not offer technical support for the DAW software in the DVD-ROM.
• Use of the software and this manual is governed by the license agreement which the purchaser fully agrees to upon breaking the seal of the software
packaging. (Please read carefully the Software Licensing Agreement at the end of this manual before installing the application.)
• Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the
manufacturer.
• Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of
the use of this manual and the software.
• This disk containing the software is not meant for use with an audio/visual system (CD player, DVD player, etc.). Do not attempt to use the disk on
equipment other than a computer.
• Future upgrades of application and system software and any changes in specifications and functions will be announced separately on Yamaha site.
• The screen displays as illustrated in this manual are for instructional purposes, and may appear somewhat different from the screens which appear on your
computer.
• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use
others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and
sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of
copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.
• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal
use.
• Windows is a registered trademark of Microsoft® Corporation in the United States and other countries.
• Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries.
The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
Connections
Maintenance
Handling caution
Saving data
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.Owner’s Manual 5
Introduction
6
Thank you for purchasing the Yamaha KX25 / KX49 / KX61 USB KEYBOARD STUDIO.
The package includes the MIDI keyboard for controlling a computer via USB and the DAW application
software, Cubase AI4. Simply connecting a computer to the KX via a USB cable port enables you to configure
an ideal environment for music production.
In order to take full advantage of the KX’s superior functionality and enjoy years of trouble-free use, please
read this manual before you begin using the product. Also, keep this book in a safe place for future reference.
Link with Cubase
This keyboard is equipped with the Link functions matching Cubase 4 / Studio 4 / AI 4, letting you produce
music with tremendous efficiency.
Track Operations of the VSTi (VST instrument)
From the KX panel, you can perform the VSTi operations such as track creation and Voice selection.
Four Knobs letting you control various parameters
This keyboard is equipped with the four knobs useful for control the parameters of the VSTi software
synthesizer. Just by selecting the Control Template for the software synthesizer you want to control, you can
use the knobs to control parameters of the software synthesizer. The KX provides 30 preset Control Templates
for various software synthesizers, which can be edited or customized to assign your favorite functions to the
knobs.
Powerful Arpeggio feature
The KX features the Arpeggiator, letting you play various phrases depending on the notes you pressed. You
can easily call up various phrases such as the analog synthesizer-like one, backing performance of guitar or
bass and drum/percussion rhythm pattern.
USB bus-powered supported
The KX can be used as a bus-powered type device (powered by the host computer via the USB connector).
Simply connecting a computer to the KX via a USB cable supplies the power from the computer to the KX.
• AC power adaptor (PA-3C, PA-130, or an equivalent)*
• Owner’s Manual (this book)
• USB cable (black, 1.5m)
• Cubase AI4 DVD-ROM
• TOOLs for KX DVD-ROM
* May not be included depending on your particular area. Please check with your Yamaha dealer.
Introduction
Features
Included Accessories
About the KX Editor
The KX Editor is the application tool of the computer and used for editing various settings for the KX
instrument. This special software can be downloaded from Yamaha site.
http://?????????????????????????Owner’s Manual
About the Disks Included in the Package
The software on these disks is for the Windows XP and Mac OSX 10.4 or later.
Disk Installation Procedure
Before breaking the seal of the disk’s packaging, please read carefully the “TOOLS for KX LICENSE
AGREEMENT” and “Cubase AI4 LICENSE AGREEMENT” described at the end of this manual.
1. Verify that your system meets the operating requirements of the software by refering to the
“System Requirements for software” below.
2. Install Cubase AI4, Extensions for Steinberg DAW and USB-MIDI Driver by following the Setup
procedure on page 13.
3. Start up the software.
For subsequent operations, refer to the corresponding pages of this manual and the manual for Cubase
AI4 (online help/PDF manual).
System Requirements for Software
The system requirements below are necessary for using the KX by connecting it to a computer, or for using
the included DAW.
Windows Mac
About the Disks Included in the Package
NOTE If any of Cubase 4, Cubase Studio 4, and Cubase AI4 has already been installed, install only Extensions
for Steinberg DAW and USB-MIDI Driver.
NOTE To view PDF files on Windows, you must install Adobe Reader on your computer.
If you do not have Adobe Reader, you can download the application from the Adobe website at the
following URL:
http://www.adobe.com
NOTE · The system requirements below may differ slightly depending on the particular operating system.
· For details on minimum requirements for other DAW software, refer to the respective owner’s manual.
OS: Windows XP Professional/XP Home
Edition
Computer: Intel Pentium 1.4 GHz or better
Memory: 512MB
Display
Resolution: 1024 x 768 pixel
Interface: Equipped with the USB connector
Hard Disk: Free disk space of 400 MB or more;
high-speed hard disk
NOTE A DVD drive is required for installation.
OS: Mac OSX 10.4 or later
Computer: Power Mac G4 1GHz or Core Solo
1.5GHz or better
Memory: 512MB
Display
Resolution: 1024 x 768 pixel
Interface: Equipped with the USB connector
Hard Disk: Free disk space of 400 MB or more;
high-speed hard disk
NOTE A DVD drive is required for installation.Owner’s Manual 7
Owner’s Manual
8
Introduction.....................................6
Features ..........................................6
Included Accessories......................6
About the Disks Included in the
Package...........................................7
Disk Installation Procedure ......................................7
System Requirements for Software .........................7
Turning the Power On and Off ........9
Power Supply ...........................................................9
Connecting the AC Power Adaptor ....................9
Using the KX as a USB bus-powered device.....9
Turning the Power On and Off .................................9
Front and Rear Panels...................10
What You Can Do With KX ............12
Keyboard performance...........................................12
Transport/Track operations on the DAW software
..12
Window operations on the VSTi.............................12
Parameter control of the tone generator in the
computer ................................................................12
Phrase/rhythm performance by using the
Arpeggiator.............................................................12
Setting Up......................................13
Installation using the Cubase AI 4 DVD-ROM .......13
For Windows: ...................................................13
For Macintosh: .................................................13
Installation using the TOOLS for KX DVD-ROM ....13
For Windows: ...................................................14
For Macintosh: .................................................15
Connection .............................................................16
Using the KX with Cubase ............17
Setting up on the KX ..............................................17
Setting up on Cubase.............................................17
Start the KX and Cubase .......................................18
Controlling the Transport and Tracks remotely ......19
Setting up the VSTi ................................................20
Creating a track for the VSTi............................20
Opening the VSTi window and selecting an
Instrument ........................................................20
Changing the MIDI message type generated via
the PROGRAM [DEC] and [INC] buttons .........21
Controlling the VSTi by using the
CONTROL knobs ...................................................22
Selecting/Editing a Control Template.....................23
Selecting a Control Template .......................... 23
Changing the message type generated by using
the CONTROL knob
(Editing a Control Template)............................ 23
Changing the Control Change generated by using
the CONTROL knob
(Editing a Control Template)............................ 24
Using the Buttons for controlling Cubase .............. 25
Using the CUBASE FUNCTION ...................... 25
Assigning the function to the buttons for
controlling Cubase ........................................... 25
Basic operation on the KX............ 26
Indication on the display ........................................ 26
Changing the octave range ................................... 27
Selecting the Velocity Curve.................................. 27
Using the Arpeggiator................... 28
Arpeggio playback ................................................. 28
MIDI Clock controlling the Arpeggio Tempo .... 29
Editing an Arpeggio ............................................... 30
Arpeggio parameters ............................................. 30
Using the KX with a DAW other than
Cubase .......................................... 31
MIDI ports on the KX ....................................... 32
When using Digital Performer (Mark of the
Unicorn Inc.) or Logic Pro (Apple Inc.): ........... 33
Utility Settings.............................. 34
Basic Operation ..................................................... 34
Utility Parameters .................................................. 34
Restoring the Factory-programmed System
(Factory Set) .......................................................... 35
Setting the MIDI Thru parameter ........................... 36
Troubleshooting............................ 37
Message List ................................. 38
TOOLS for KX LICENSE
AGREEMENT ................................. 39
Cubase AI4 LICENSE
AGREEMENT ................................. 40
Appendix ....................................... 42
Specifications ........................................................ 42
Control Template List ............................................ 43
Arpeggio Type List................................................. 44
Table of contents
Turning the Power On and Off
Power Supply
The KX can be powered from one of the following
two power supplies.
• Power supply from the AC power adaptor
• Power supply from the connected host computer
(USB bus-power)
Connecting the AC Power Adaptor
1. Make sure that the STANDBY/ON switch of
the KX is in the STANDBY position.
2. Connect the plug of the power adaptor to
the DC IN terminal on the rear panel.
3. Plug the power adaptor into a standard
household power outlet.
WARNING
• Use only the included power adaptor (PA-3C or PA130) or an equivalent recommended by Yamaha).
Use of a different adaptor may result in equipment
damage, overheating, or fire. In such cases, the
product warranty will be void immediately even within
the effective warranty period.
CAUTION
• Wrap the DC output cable of the adaptor around the
cable clip (as shown below) to prevent accidental
unplugging of the cable during operation. Avoid
tightening the cord more than necessary or pulling on
the cord strongly while it is wrapped around the cable
clip to prevent wear on the cord or possible breakage
of the clip.
Using the KX as a USB bus-powered
device
The KX is the bus-powered type device which can
be powered by the host computer connected via a
USB cable. In this case, the AC power adaptor is
not necessary.
1. Make sure that the STANDBY/ON switch of
the KX is in the STANDBY position.
2. Connect a computer to the USB TO HOST
connector of the KX by using a USB cable.
3. Start the computer.
Turning the Power On and Off
1. Turn the power ON by pressing the
[STANDBY/ON] switch so that this switch is
in the ON position.
2. Turn the power off by pressing the
[STANDBY/ON] switch again so that this
switch is returned to the STANDBY position.
CAUTION
• Note that a small amount of current continues to flow
while the switch is in the STANDBY position. If you
do not plan to use the KX again for a long while, be
sure to unplug the adaptor from the wall outlet and
unplug the USB cable from the KX.
Turning the Power On and Off
KX61
NOTE · While the KX is turned ON, the computer
connected to the KX via USB cannot enter
the power-saving mode (such as sleep
and suspended) even if you do not
operate the computer for a long time. This
situation vampires the power of the
computer although you do not use the
computer. Especially when the computer
is powered by the battery (not the power
adaptor), make sure that the STANDBY/
ON switch of the KX is in the STANDBY
position to save the power consumption.
· The USB bus-power function can be used
only when connecting the KX to a
computer directly without using a hub or
connecting the KX to a computer via a
self-powered USB hub. This function
cannot be used when connecting the KX
to a computer via a bus-powered USB
hub.
· The USB bus-power function will not work
when using the AC adaptor.Owner’s Manual 9
Front and Rear Panels
101 CONTROL knobs .............................Page 22
Use these knobs to adjust the values of the
parameters such as VSTi in the connected
computer.
2 Knob Functions Select button .......Page 22
Use this button to select one of the two
functions assigned to each knob.
3 VELOCITY CURVE [DEC] and [INC]
buttons .............................................Page 27
Use these buttons to select one of the velocity
curves of the keyboard.
4 OCTAVE buttons .............................Page 27
Use these buttons to change the note range of
the keyboard by octave.
5 [EXIT] button....................................Page 26
Press this button to return to the original
display.
6 [UTILITY] button ..............................Page 34
Press this button to call up the display which
lets you set the system related parameters.
7 [ARP EDIT] button ...........................Page 28
Press this button to call up the display which
lets select the Arpeggio type and set the
related parameters.
8 [CONTROL TEMPLATE] button......Page 23
Use this button to select a template assigned to
CONTROL knobs.
9 [ARP ON/OFF] button .....................Page 28
Press this button to enable or disable the
playback of the Arpeggio. Turning on the
button lights up the LED lamp.
) [HOLD] button .................................Page 28
This button turns the Arpeggio Hold function on
and off.
! TEMPO LED ....................................Page 29
This LED lamp flashes in time with the tempo of
the Arpeggio.
@ SELECT buttons..............................Page 26
Use these buttons to select the parameter to be
edited.
# DATA [DEC] and [INC] buttons
..................................................Pages 17, 28
Use each of these buttons to increase or
decrease the value of the selected parameter.
$ Display .............................................Page 26
Shows the related information according to
your panel operations.
% [VSTi WINDOW] button...................Page 20
Press this button to switch between displaying
and hiding the VSTi window on the Cubase.
^ [ADD INSTRUMENT TRACK] button
..........................................................Page 20
Press this button to create a VSTi track on the
Cubase.
Front and Rear Panels
1
2 9 )
7 8
5 6 !
@
3 4 # $
¢ ∞Owner’s Manual
Front and Rear Panels& CUBASE FUNCTION [A] and [B] buttons
..........................................................Page 25
Use these buttons to control Cubase because
some functions of Cubase can be assigned to
these buttons.
* PROGRAM [DEC] and [INC] buttons
..........................................................Page 20
Use these buttons to select the Voice program
of the VSTi assigned to the track selected on
the DAW software.
( Cursor buttons ................................Page 19
This button works the same as the Cursor keys
on your computer.
º [ESC] button ....................................Page 19
This button works the same as the ESC key on
your computer.
¡ [ENTER] button................................Page 19
This button works the same as the ENTER key
on your computer.
™ Track Control buttons.....................Page 19
Use these buttons to control Cubase tracks
remotely.
£ Transport Control buttons..............Page 19
Use these buttons to control the transport
functions such as recording and playback in
Cubase remotely.
¢ Modulation wheel....................Pages 12, 17
Controls the modulation effect.
∞ Pitch Bend wheel ....................Pages 12, 17
Controls the pitch bend effect, making
continuous pitch change.
§ [STANDBY/ON] switch......................Page 9
Press this switch to turn the power on or off
(STANDBY).
¶ DC IN connector................................Page 9
Connect an AC adaptor to this jack.
• MIDI IN connector ...........................Page 16
This connector is used to receive MIDI
messages transmitted from an external MIDI
device.
ª MIDI OUT connector .......................Page 16
This connector is used to transmit MIDI
messages to an external MIDI device.
‚ SUSTAIN jack ..................................Page 16
Connect an optional foot switch (such as
Yamaha FCxxx) to this jack.
⁄ USB TO HOST connector ...............Page 16
This connector is used to connect the keyboard
and the computer by using a USB cable.
Because the KX is the bus-powered type
device, the power can be supplied from the
computer to the KX via this connector.
º ¡

*
&
% ^
(
§ ¶ • ª ‚ ⁄Owner’s Manual 11
What You Can Do With KX
12The KX lets you use the following functions as well as the MIDI keyboard function.
Keyboard performance
You can play the keyboard or control various
controller such as the Pitch Bend wheel and
Modulation wheel to play the VSTi on the computer
connected via USB or play the MIDI tone generator
connected via MIDI.
Transport/Track operations
on the DAW software
You can perform the transport controls such as
Rec/Play/Stop and the track controls such as Mute/
Solo switching in Cubase remotely.
Window operations on the
VSTi
When using Cubase, you can open or close the
VSTi related window and create the track for the
VSTi from the KX.
Parameter control of the
tone generator in the
computer
You can remotely control parameters of the tone
generators such as the VSTi and synthesizer by
using the CONTROL knobs.
Phrase/rhythm performance
by using the Arpeggiator
You can easily call up various phrases such as the
analog synthesizer-like one, backing performance
of guitar or bass and drum/percussion rhythm
pattern.
What You Can Do With KX
KX
Keyboard
MIDI Select =
MIDI
MIDI tone
generator
Software synthesizer
MIDI Select = USB
DAW software
KX
Rec/Play/
Stop
DAW software
Mute/Solo
KX
Button
operation
Opening/Closing
the VSTi window Creating a Track
KX
VSTi
Cubase
KX
Arpeggiator
Arepeggio
DAW softwareOwner’s Manual
Setting UpInstallation using the Cubase AI 4 DVD-ROM
Important!
Since the End-User Software License Agreement (EUSLA) showed on your PC-display in your installing the
“DAW” software is replaced by the agreement on page 40, you should disregard the EUSLA. Read the
Cubase AI 4 License Agreement on page 40 carefully, and install the software if you agree to it.
For Windows:
1. Start the computer and log on to the
Administrator account.
2. Insert the Cubase AI4 DVD-ROM into the
DVD-ROM drive.
3. Open the DVD-ROM, then double-click the
file “CubaseAI4.msi.”
Follow the instructions on the screen to install
Cubase AI4.
For Macintosh:
1. Start the computer and log on to the
Administrator account.
2. Insert the Cubase AI4 DVD-ROM into the
DVD-ROM drive.
3. Open the DVD-ROM, then double-click the
file “CubaseAI4.mpkg.”
Follow the instructions on the screen to install
Cubase AI4.
Installation using the TOOLS for KX DVD-ROM
“TOOLS for KX” DVD-ROM includes the following application software tools.
• Installer of “Extensions for Steinberg DAW”
• USB-MIDI driver
• VSTi installer developed by other companies
From among the above tools, “Extensions for Steinberg DAW” should be installed so that you can use Cubase
conveniently and the USB-MIDI Driver should be installed so that communication between the KX and the
computer can be performed. VSTi can be installed as desired.
Setting Up
NOTE Install Cubase AI4 before installing Extensions for Steinberg DAW. It is because the KX project templates
will be installed in the installation destination of Cubase AI4.
NOTE · When installing Cubase AI4, you will need a working internet connection to register your Cubase AI 4.
Make sure to fill in all required fields for user registration. If you do not register the product, you will be
unable to use the application after a limited period of time expires.
· If you are using Cubase 4 or Cubase Studio 4, install either application before you install Extensions for
Steinberg DAW. The KX project templates will be installed in the application installation destination.
NOTE · If you want to install the VSTi developed by other companies, follow the Installation Guide for each VSTi
located in the “VSTis” folder.
· For information on how to uninstall each software, refer to the Installation Guide located in a folder of
each software.Owner’s Manual 13
Setting Up
14For Windows:
1. Make sure that the power to the KX is turned
off.
2. Disconnect all MIDI cables that connect MIDI
devices to MIDI IN/OUT connectors on the
KX.
3. After disconnecting all other USB devices
from the computer, connect the KX directly
to the computer (without using a hub) by
using a USB cable.
4. Start the computer and log on to the
Administrator account.
5. Insert the “TOOLS for KX DVD-ROM” into
the DVD-ROM drive.
6. Open the “Extensions for Steinberg DAW”
folder in the DVD-ROM, then double-click
the file “setup.exe”
The first display for installing “Extensions for
Steinberg DAW” appears.
7. Click [Next] to call up the “Welcome to the
InstallShield Wizard for Yamaha Extensions
for Steinberg DAW” window.
8. Click [Next] to start the installation.
To cancel the installation procedure, click
[Cancel].
9. When the installation is complete, a
message indicating that installation is
complete appears. Click [Finish].
10. Turn the power on of the KX by pressing the
[STANDBY/ON] switch.
The KX will be recognized by the connected
computer.
11. Install the USB-MIDI driver.
The installation has been completed.
NOTE · If the same version of Extensions for
Steinberg DAW has already been
installed in your computer, the completion
of the maintenance window appears. In
this case, click [Finish].
· If a newer version of Extensions for
Steinberg DAW has already been
installed in your computer, a dialog box
appears indicating that the newer
software has already been installed. In
this case, you do not need to install the
software. Click [OK] in the dialog box.
· If an older version of Extensions for
Steinberg DAW has been installed in your
computer, the software should be
updated. (The procedure is the same as
for installing it from scratch.)
NOTE During the installation procedure, you can
select the type of “Extensions for Steinberg
DAW” by selecting “Custom” in the “Setup
Type” dialog.
NOTE Installation of the USB MIDI driver is
described in “installationguide_**.pdf” stored
in the “USB-MIDI_Driver” folder.Owner’s Manual
Setting UpFor Macintosh:
1. Make sure that the power to the KX is turned
off.
2. Disconnect all MIDI cables that connect MIDI
devices to MIDI IN/OUT connectors on the
KX.
3. After disconnecting all other USB devices
from the computer, connect the KX directly
to the computer (without using a hub) by
using a USB cable.
4. Start the computer and log on to the
Administrator account.
5. Insert the “TOOLS for KX DVD-ROM” into
the DVD-ROM drive.
6. Open the “Extensions for Steinberg DAW”
folder in the DVD-ROM, then double-click
the file “Yamaha Extensions for Steinberg
DAW.mpkg”.
The “Welcome to the InstallShield Wizard for
Yamaha Extensions for Steinberg DAW”
window appears.
7. Click [Continue].
8. Execute the installation by following the
directions appearing on the screen.
9. When the installation is complete, a
message indicating that installation is
complete appears. Click [Close].
10. Install the USB-MIDI driver.
11. Turn the power on of the KX by pressing the
[STANDBY/ON] switch.
The KX will be recognized by the connected
Mac computer.
The installation has been completed.
NOTE · If a dialog box appears asking if you want
to install the software, click [Continue].
· If “Extensions for Steinberg DAW” has
been installed, it will be overwritten by the
new installed version.
NOTE · You can select only the startup disk as
installation destination.
· During the installation procedure, you can
select the type of “Extensions for
Steinberg DAW” by selecting “Customize”
in the “Installation Type” dialog.
NOTE · Installation of the USB MIDI driver is
described in “installationguide_**.pdf”
stored in the “USB-MIDI_Driver” folder.
· The “Keyboard Setup Assistant” window
appears when connecting the KX to a
computer via USB. In this case, click the
red circle at the top left corner to close
this window.Owner’s Manual 15
Setting Up
16Connection
The following connection, for example, is necessary for using the KX.
NOTE · With the initial default settings (MIDI Select = USB …page 34, MIDI Thru = MIDI → USB …page 36), the
KX can control the DAW software on your computer via a USB cable after installation procedures (pages
13–15) have been completed. For example, you can play the Voices of the software synthesizer like
VSTi standard on your computer by playing the keyboard of the KX. Furthermore, MIDI messages
generated on the MIDI device (synthesizer on the above illustration) connected to the KX via a MIDI
cable can be transmitted through the KX to the computer. It means song playback of the MIDI device can
play the Voices of the software synthesizer like VSTi standard on your computer.
· When the MIDI Select parameter (page 34) is set to “MIDI,” the USB connector will be inactive resulting
that MIDI communication can be performed only via the MIDI connectors. In the example illustration
above, you can play the sound of the tone generator by playing the KX keyboard.
1
2
Computer
USB connector USB cable
Audio interface
MIDI OUT connector
MIDI IN connector
Footswitch (optional)
Synthesizer, Tone generator,
Rhythm Machine, etc.
Headphone
KX rear panel
M
ID
I c
ab le M
ID
I c
ab leOwner’s Manual
Using the KX with CubaseThe KX features a special Link function that enables you to link the KX with Cubase. Using this function, you
can produce music with tremendous efficiency by creating a track from the KX. As an example, this section
describes using Cubase 4 with the Link function.
Setting up on the KX
To use the Link function with Cubase, it is
necessary to change the settings of the KX
according to the DAW on your computer.
1. Press the [UTILITY] button to call up the
Utility display.
2. Use the SELECT buttons to call up “DAW
Select.”
In this state, you can select the DAW software
controlled from the KX.
3. Use the DATA [DEC] and [INC] buttons to
select the desired DAW software.
■ When using Cubase 4/Cubase Studio 4:
Select “Cubase4.”
■ When using Cubase AI4:
Select “CubaseAI.”
4. Press the [EXIT] button to return to the
original display.
Setting up on Cubase
The MIDI messages generated on the KX (by
playing the keyboard, controlling the Pitch Ben
Wheel and the Modulation Wheel, and so on) are
transmitted via the USB-MIDI port1 from the KX to
Cubase. The messages transmitted via the USBMIDI port1 and port2 are not related to the music
performance (including the Intsrument change),
resulting that the computer may recognize these
messages as the Instrument change and play the
unexpected sound. To avoid such a situation, you
should remove the checkmark of “All MIDI Input” for
the USB-MIDI port 2 and port 3.
1. Select “Device Setup” from the “Device”
menu of Cubase.
The Device dialog appears.
2. Click “MIDI Port Setup” in the Devices
column.
The MIDI ports of Cubase appear at right of the
dialog.
Using the KX with Cubase
NOTE The procedure here is not necessary when
using Cubase AI4 included in the accessory
DVD-ROM.
NOTE · Explanation here uses the display of
Windows. You can perform the
instructions below also when using
Macintosh.
· For information about the USB-MIDI port
1–3 handled by the KX, refer to page 32.Owner’s Manual 17
Using the KX with Cubase
183. Remove the checkmark by clicking the
check box of “All MIDI Input” for the KX MIDI
Port 2 and 3 respectively.
4. Click [OK] close the dialog.
5. Quit Cubase.
Start the KX and Cubase
1. Make sure that the STANDBY/ON switch of
the KX is in the STANDBY position, then
connect the KX to your computer by using a
USB cable.
2. Press the STANDBY/ON switch to turn the
power ON.
3. Start Cubase on the computer.
Yamaha KX Yamaha KX Port 2/3
Remove the checkmark.
Click “MIDI Port Setup.”
NOTE Cubase cannot recognize the KX if you turn
the power of the KX ON after starting
Cubase. Make sure to start Cubase before
turning the power the KX ON.Owner’s Manual
Using the KX with CubaseControlling the Transport and Tracks remotely
You can perform the transport controls (such as recording and playback) and the track controls such as Mute/
Solo switching in Cubase via the panel operation of the KX.
Cursor buttons ...........This button works the same
as the Cursor keys on your
computer.
[ENTER] button ..........This button works the same
as the Enter (return) key on
your computer.
[ESC] button...............This button works the same
as the Esc (esc) key on your
computer, such as the
operation cancel.
Track Control buttons
Select the track of Cubase and perform the Mute/
Solo switching of the selected track.
[ASSIGN 1] button .....Executes the MIDI Quantize
command.
[ASSIGN 2] buttons ...Executes the Delete
Command.
[MUTE] button............Switches the Mute of the
selected track On or Off.
[SOLO] button............Switches the Solo of the
selected track On or Off.
Transport Control buttons
Use these buttons to control the transport functions
such as recording and playback.
[ ] button............. rewind
[ ] button............. fast forward
[ ] button................ repeat on/off
[■] button...................stop
[ ] button.................play
[REC] button .............. record
Cursor buttons, [ENTER]/[ESC] button Track Control buttons
Transposrt Control buttonsOwner’s Manual 19
Using the KX with Cubase
20Setting up the VSTi
You can create a track for the VSTi and open/close the VSTi window from the KX panel operation remotely.
Performing such operations (normally performed on Cubase) from the KX panel allows you to produce music
with tremendous efficiency.
Creating a track for the VSTi
You can simply create a track for the VSTi
(Instrument Track) from the KX panel operation
remotely.
1. Press the [ADD INSTRUMENT TRACK]
button of the KX.
The [Add Instrument Track] dialog appears.
2. Click “No VST Instrument” by using a
mouse.
3. Select the desired VSTi by using the Cursor
buttons of the KX.
4. Press the [ENTER] button to fix the selected
VSTi.
The [Add Instrument Track] dialog closes.
Opening the VSTi window and
selecting an Instrument
When the Instrument Track is selected on the
Project window or the other window, you can open
the VSTi window quickly at the touch of the button
on the KX’s panel.
1. On the KX, use the Cursor buttons to select
an Instrument Track of which the VSTi
window you want to call up.
2. On the KX, press the [VSTi WINDOW] button
to open the VSTi window.
The VSTi window of the track selected in step 1
will appear.
3. On the computer, click the Instrument select
box of the VSTi window to call up the
window as illustrated below.
4. On the KX, use the PROGRAM [DEC] and
[INC] buttons to select an Instrument.
5. Press the [VSTi WINDOW] button again to
close the VSTi window.
NOTE Please keep in mind that a new Instrument
Track cannot be created if any project file is
not opened. After opening a project file or
create a new project file, perform this
procedure.Owner’s Manual
Using the KX with CubaseChanging the MIDI message type
generated via the PROGRAM [DEC]
and [INC] buttons
With the default initial settings, pressing either of the
PROGRAM [DEC] and [INC] buttons transmits two
types of the MIDI messages: Program Change and
VSTi Remote. Depending on the VSTi, an Instrument
is selected via several cases: only the Program
Change, only the VSTi Remote message, and both
the Program Change and VSTi Remote. You can set
which message is transmitted when pressing the
PROGRAM [DEC]/[INC] button according to the
specification of the VSTi.
1. Press the [UTILITY] button.
The LED lamp above the button lights and the
Utility display appears.
2. Use the SELECT [▲] and [▼] buttons to call
up “PrgChgMode.”
3. Use the DATA [DEC] and [INC] buttons to
select the desired setting from the following
menus.
4. Press the [EXIT] button to return to the Top
display.
PC+Remote
When this is selected, pressing the
PROGRAM [DEC]/[INC] button
trasnmits both the Program Change
message and the VSTi Remote
messages.
ProgChg
When this is selected, pressing the
PROGRAM [DEC]/[INC] button
transmits only the Program Change
message.
Remote
When this is selected, pressing the
PROGRAM [DEC]/[INC] button
transmits only the VSTi Remote
message.Owner’s Manual 21
Using the KX with Cubase
22Controlling the VSTi by using the CONTROL knobs
Operating the CONTROL knobs on the KX panel edits or controls various parameters of the VSTi used on the
computer. The KX provides the 30 Control Templates which can be used for the VSTi software synthesizers.
By selecting the desired one from 30 Control Templates, you can assign the functions appropriate for the
current VSTi to the CONTROL knobs.
When using Cubase, selecting an Instrument track or changing the VSTi assigned to the current track will
change the Control Template on the KX automatically. This means that you need not select the Control
Template manually when using Cubase.
When the Top display is shown, the names of the parameters to be adjusted via the CONTROL knobs are
shown normally. When controlling the knob, the values of the parameters are shown for a while then the
original display appears again.
Using the Automation function of Cubase lets you record your knob operations to an Instrument track. For
details about the Automation function, refer to the manual of Cubase.
NOTE · For details about the available Control Template, refer to the Control Template List on page 43.
· The time of the value indication can be changed. For details, refer to “Utility Settings” on page 34.
· When using the DAW other than Cubase, you need to change the Control Template manually via the KX
panel operation.
Use these knobs to adjust the values of the VSTi parameters.
Eight parameters can be adjusted because you can switch the parameter assignment
by using the Knob Functions Select button.
Use this button to switch the parameters to be adjusted via the
CONTROL knobs (between parameters 1–4 and 5–8).
This lamp lets you confirm which parameter set (1–4 or 5–8) is
assigned to the CONTROL knobs.Owner’s Manual
Using the KX with CubaseSelecting/Editing a Control Template
When using the DAW other than Cubase, the Control Template on the KX is not selected automatically by the
DAW operation on the computer unlike the Cubase, meaning that you need to select a Control Template
manually via the panel operation on the KX.
When using any DAW including Cubase, you can edit the Control Template to change the type of the
message generated via the knob operation and functions assigned to the knobs.
Selecting a Control Template
1. Press the [CONTROL TEMPLATE] button.
The LED lamp lights and the Control Template
selection display appears.
In this state, you can select the Control Template.
2. Use the DATA [DEC] and [INC] buttons to
select the desired Control Template.
3. Press the [EXIT] button to return to the
original display.
The LED lamp of the [CONTROL TEMPLATE]
button will be turned off.
In this state, the VSTi parameters according to
the template selected in step 2 are assigned to
the CONTROL knobs.
Changing the message type
generated by using the CONTROL
knob (Editing a Control Template)
You can select the type of the MIDI messages
generated and transmitted by controlling the
CONTROL knob: “Control Change (CC)” and “VSTi
Remote.” Normally, the VSTi can be controlled by
the Control Change or VSTi Remote.
Control Change ......... The MIDI Control Change
messages adjust the VSTi
parameters.
VSTi Remote .............. The automation function of
the VSTi adjusts the VSTi
parameters.
The KX provides the Control Templates each of
which includes the settings most appropriate for
each VSTi. Note that the settings of each template
can be edited as desired.
1. Press the [CONTROL TEMPLATE] button.
The LED lamp lights and the Control Template
selection display appears.
2. Use the DATA [DEC] and [INC] buttons to
select the desired Control Template.
3. Use the SELECT [▲] and [▼] buttons to call
up “KnobOutSel.”
NOTE Using the KX Editor (page 6) which can be downloaded from Yamaha web site, lets you edit all the Control
Templates.
NOTE When the different display appears even if
pressing the [CONTROL TEMPLATE]
button, press the [CONTROL TEMPLATE]
button again or press the SELECT [▲]
button once or twice to call up the Control
Template selection display.
NOTE You can increase the value by 10 by
simultaneously holding down the [DEC]
button and pressing the [INC] button, while
you can decrease the value by 10 by
simultaneously holding down the [INC]
button and pressing the [DEC] button.
Lighting
NOTE · The VSTi Remote function is available
only when using the Cubase 4 / Cubase
Studio 4 / Cubase AI4.
· The setting here is to be store on internal
memory automatically (without the store
operation). If you want to back up the
setting here, use the KX Editor (page 6) to
store the setting to a computer.
NOTE When the different display appears even if
pressing the [CONTROL TEMPLATE]
button, press the [CONTROL TEMPLATE]
button again or press the SELECT [▲]
button once or twice to call up the Control
Template selection display.Owner’s Manual 23
Using the KX with Cubase
244. Use the DATA [DEC] and [INC] buttons to
select the desired type of the message.
CC:......................Control change
Remote:...............VSTi remote
5. Press the [EXIT] button to return to the
original display.
Changing the Control Change
generated by using the CONTROL
knob (Editing a Control Template)
When the KnobOutSel parameter (page 23) is set to
“CC” (Control Change), you can change the Control
Change number assigned to the CONTROL knob
from the default one to your desired one.
1. Press the [CONTROL TEMPLATE] button.
The LED lamp lights and the Control Template
selection display appears.
2. Use the DATA [DEC] and [INC] buttons to
select the desired Control Template.
3. Use the SELECT [▲] and [▼] buttons to
select the desired CONTROL knob.
4. Use the DATA [DEC] and [INC] buttons to
change the Control Change number of the
selected CONTROL knob.
5. Press the [EXIT] button to return to the
original display.
NOTE The setting here is to be store on internal
memory automatically (without the store
operation). If you want to back up the setting
here, use the KX Editor (page 6) to store the
setting to a computer.
NOTE When the different display appears even if
pressing the [CONTROL TEMPLATE]
button, press the [CONTROL TEMPLATE]
button again or press the SELECT [▲]
button once or twice to call up the Control
Template selection display.
NOTE The Control Changes which can be used to
adjust the parameters differ depending on
the VSTi. For details, refer to the manual of
the VSTi.
NOTE The display of the KX shows the Control
Change number in decimal. Keep in mind
that the Control Change number may be
described in hexadecimal depending on the
manual of the VSTi.Owner’s Manual
Using the KX with CubaseUsing the Buttons for controlling Cubase
Using the CUBASE FUNCTION
When using Cubase, you can call up various
windows of Cubase by using the CUBASE
FUNCTION [A] and [B] buttons.
■ When using Cubase 4/Cubase Studio 4:
The CUBASE FUNCTION [A] button can be used
for calling up the Sound Frame dialog.
The CUBASE FUNCTION [B] button can be used
for calling up the Mixer window.
■ When using Cubase AI4:
The CUBASE FUNCTION [A] button can be used
for calling up the List Editor window.
CUBASE FUNCTION [B] button can be used for
calling up the Mixer window.
The functions of the CUBASE FUNCTION [A] and
[B] buttons can be changed as desired. For details,
see the next section.
Assigning the function to the
buttons for controlling Cubase
The buttons for controlling Cubase can be changed
as necessary. To do this, follow the instructions
below:
1. Select “Device Setup” from the “Device”
menu.
The “Device Setup” dialog appears.
2. Click “Yamaha KX” in the Device column.
The following buttons are assignable.
• CUBASE FUNCTION [A] and [B] buttons
• [ASSIGN 1] and [ASSIGN 2] buttons
• [MUTE] button
• [SOLO] button
• [VSTi WINDOW] button
• [ADD INSTRUMENT] button
3. Click the Category column of the desired
button, then select the desired Category
from the pop-up menu.
When selecting the Category including multiple
commands, click the Command column then
select the desired function from the pop-up
menu.
4. Click [OK] after completing the setup.
The “Device Setup” dialog closes.
Category Command
Click “Yamaha KX.”Owner’s Manual 25
Basic operation on the KX
26This section describes the basic operations such as how to shift the octave range of the keyboard and use the
display interface.
Indication on the display
The display shows various parameters depending on your panel operation.
Top display
This display appears when turning the power ON.
Parameters edited via the CONTROL knobs are
shown on the display.
Operating any of the CONTROL knob calls up the
values on the display. After a while, the display
returns to the original indication.
Arpeggio Edit display
This display appears by pressing the [ARP EDIT]
button so that its lamp lights. This display lets you
select the Arpeggio type and set the related
parameters. Press the [EXIT] button to return to the
original Top display.
Control Template display
This display appears by pressing the [CONTROL
TEMPLATE] button so that its lamp lights. This
display lets you select a template assigned to the
CONTROL knobs. Press the [EXIT] button to return
to the original Top display.
Utility display
This display appears by pressing the [UTILITY]
button so that its lamp lights. This display lets you
set the system related parameters. Press the [EXIT]
button to return to the original Top display.
From these displays, you can call up the desired
parameters by using the SELECT [▲] and [▼]
buttons. Note that “:” is indicated at the left of the
editable parameter. You can confirm which
parameter is actually editable because “:” of the
current parameter blinks.
Basic operation on the KX
NOTE The display illustrated below may appear
when turning the power ON. This indicates
that Cubase and VSTi have not been started
on the computer connected to the KX via
USB. If you intend to use Cubase, start
Cubase and VSTi, resulting that this
indication disappear and the Top display
illustrated above appear. If you intend to use
the DAW other than Cubase, set the DAW
Select parameter (page 34) to the
corresponding one (other than “Cubase” or
“Cubase AI”).
NOTE You can set the desired amount of time for
which the values are contemporarily
indicated on the display. For instructions,
see page 34.
Lights
Lighting
Lighting
Blinking
Parameter ValueOwner’s Manual
Basic operation on the KXChanging the octave range
Use these buttons to shift the note range of the
keyboard by octave, up/down to three octaves. The
initial default setting (no transpose) is recalled by
pressing both the buttons simultaneously.
The current octave range can be confirmed via the
status of the LED lamp above the button.
Selecting the Velocity
Curve
You can select the desired Velocity Curve which
indicates how velocities are applied to your
pressing strength. Use the VELOCITY CURVE
[DEC] and [INC] buttons to select a Velocity Curve.
The following Velocity Curves are available:
Press the VELOCITY CURVE [DEC] and [INC]
buttons simultaneously to select “Fix.” The Fix
setting lets you play the notes with the fixed velocity
no matter how hard or soft you play the notes.
You can set the fixed velocity by pressing one of
the VELOCITY CURVE [DEC] and [INC] buttons.
Pressing both the buttons simultaneously exits from
this status (Fix setting) to the last selected Velocity
Curve.
(Flashing)
three octaves lower
two octaves lower
one octave lower
Initial default setting
one octave upper
two octaves upper
(Flashing)
three octaves upper
NOTE You can invert the LED status (on or off) of
the OCTAVE buttons. For information about
how to invert the LED status (on or off), refer
to “Utility Settings” on page 34.
Pressing the button to shifts
the range of the keyboard
down in octave.
Pressing the button to shif
the range of the keyboard
in octave.
Reverts the octave setting to
default.
Soft2
This curve provides increased response
(more than “Soft1”), especially for lower
velocities.
Soft1
This curve provides increased response,
especially for lower velocities.
Normal
This linear “curve” produces one-to-one
correspondence between the strength of
your keyboard playing (velocity) and the
actual sound change.
Hard1
This curve effectively lessens the overall
response compared to the “norm” curve.
Hard2
A stronger playing produces the velocities
according to the curve almost equivalent to
“Normal” and a softer playing decreases
the response. This curve is suitable for
playing the HALionOne.
NOTE From the Utility display (page 26), you can
select a Velocity Curve and specify the
velocity value carefully when the Fix is
selected. For details, refer to “Utility
Settings” on page 34.
Velocity valueOwner’s Manual 27
Using the Arpeggiator
28The Arpeggiator lets you play various phrases depending on the notes you pressed. You can trigger the
phrase according to the chord you play and the drum/percussion rhythm simply by pressing a note with just
one finger. This section describes how to use the Arpeggiator.
Arpeggio playback
The KX features 342 different Arpeggio types. You can select an Arpeggio type as desired then start playback
simply by pressing any note on the keyboard.
1. Press the [ARP ON/OFF] button so that its
indicator lights.
While the lamp is turned on, the Arpeggio will
be play according to the pressed key.
The following two types of playback are
available:
■ The Arpeggio will play only while holding
down the note on the keyboard.
When the lamp of the [HOLD] button is turned
off, the Arpeggio will play only while holding
down the note on the keyboard.
■ The Arpeggio playback will continue after
the notes are released.
When the lamp of the [HOLD] button is turned
on, the Arpeggio playback will continue even if
you release the notes on the keyboard.
2. Press the [ARP EDIT] button.
The LED lamp of the [ARP EDIT] button lights
and the Arpeggio Edit display appears.
3. Use the SELECT buttons to select “Cat.”
The KX provides the Arpeggio types (page 44)
divided into the Categories. You can reach the
desired Arpeggio type more quickly by
selecting a Category first.
4. Use the DATA [DEC] and [INC] buttons to
select the category of the desired Arpeggio
type.
5. Use the SELECT buttons so that the “Typ:”
blinks then use the DATA [INC] or [DEC]
button to select the Arpeggio type.
6. Select the Arpeggio type by using the DATA
[DEC] and [INC] buttons.
7. Press the [EXIT] button to return to the Top
display.
Using the Arpeggiator
NOTE The tempo of the Arpeggio playback can be synchronized with the tempo of the DAW on the computer.
For details, see page 29.
Lighting
Category
Arpeggio types
NOTE · If changing the Arpeggio type during
playback, the new Arpeggio type may
actually start after a while.
· You can operate the CONTROL knobs,
Pitch Bend wheel and Modulation Wheel
while selecting an Arpeggio type.
· Hold the [DEC] or [INC] button to
continuously change the value.
· You can increase the value by 10 by
simultaneously holding down the [INC]
button and pressing the [DEC] button,
while you can decrease the value by 10
by simultaneously holding down the [DEC]
button and pressing the [INC] button.Owner’s Manual
Using the ArpeggiatorMIDI Clock controlling the Arpeggio Tempo
With the initial default setting, the tempo of the Arpeggio playback is determined as follows.
When the MIDI clocks are received from an external MIDI device:
The Arpeggio will play back according to the tempo of the received MIDI clocks.
When the MIDI clocks are not received:
The Arpeggio will play back according to the internal tempo set on the KX.
When using Cubase, you can transmit the MIDI clocks from the computer to the KX by following the
procedure below.
1. Select “Sync Setup” from the “Transport”
menu on Cubase to call up the
Synchronization Setup dialog.
2. Enter the checkmark to the “Yamaha KX1” (when using Windows) and “MIDI
Clock Follows Project Position” of the
“MIDI Clock Destination” at the lower
right of the dialog.
When using Mac OS, enter the checkmark
to the USB-MIDI Port 1 via which the
performance data is transferred
3. Click [OK] to close the “Synchronization
Setup” dialog.
NOTE For instructions on setting the KX internal tempo, refer to “Utility Settings” on page 34.
KX
TEMPO=120
KX
TEMPO=120
When the MIDI clocks are received from an
external MIDI device:
Arpeggiator
TEMPO = Received tempo
Arpeggio
DAW software, etc.
MIDI clock
Arpeggiator
Arpeggio
DAW software, etc.
When the MIDI clocks are not received:
NOTE The KX provides three USB MIDI Ports
each of which can be used for a certain
use. For details, refer to “Using the KX
with a DAW other than Cubase” on
page 31.
NOTE · MIDI clocks are transmitted from
Cubase (on the computer) only when
recording or playback is performed on
Cubase.
· For information about the DAW
software other than Cubase and how
to transmit the clocks from the MIDI
device, refer to the owner’s manual of
the DAW software/MIDI device.
· You can select the setting which lets
you always use the internal MIDI clock
of the KX to play the Arpeggio even if
the external clocks are received from
the external MIDI device. For details,
refer to “Utility Settings” on page 34.Owner’s Manual 29
Using the Arpeggiator
30Editing an Arpeggio
Each Arpeggio type can be edited as desired. For
example, you can apply swing feel to the Arpeggio
playback and adjust the gate time of the notes of
the Arpeggio playback sequence.
1. Press the [ARP EDIT] button.
The LED lamp above the button lights and the
Arpeggio Edit display will appear.
2. Use the SELECT buttons to call up the
desired parameter.
For details about the Arpeggio parameters,
refer to the next page.
3. Use the DATA [DEC] and [INC] buttons to
change the value.
A change here is applied to playback
immediately. Editing a parameter during
Arpeggio playback lets you confirm the result
in real time.
4. When you are satisfied with the result, press
the [EXIT] button to return to the Control
Top display.
The settings you made here will be stored
automatically without the special operation. The
settings here will be maintained even if you turn
the power off or change the Arpeggio type.
Arpeggio parameters
NOTE The Arpeggio type can be edited during
playback. Note that the Arpeggio may not
play back properly if editing the Arpeggio
type during playback.
NOTE If you want to initialize the settings, use the
Factory Set operation as explained on
page 34.
Display Settings Description
Cat
DrPc, CPrc, Bass, Seq, ChSq, HySq,
ApKb, Orgn, GtPl, Strn, Bras, RdPp,
Lead
Determines the Category of the Arpeggio type you want to call up. For
details, see page 44.
Typ 1–342 Determines the Arpeggio type you want to call up. For details, see page 44.
Variation Orig, Up, Down, Alt1, Alt2, Rnd
Determines the playback variation of the Arpeggio. When any value other
than “Orig” is selected, you can shift the pitch up and down in octave for
the Arpeggio playback by adjusting the “OctRange” parameter.
Orig..........The original data preprogrammed in the KX will play back.
Up ............The Arpeggio of ascending notes will play.
Down........The Arpeggio of descending notes will play.
Alt1...........Alternates Up and Down arpeggios. The turnaround note is
played once.
Alt2...........Alternates Up and Down arpeggios. The turnaround note is
played twice.
Rnd ..........The Arpeggio will play randomly according to the pressed
notes.
OctRange -3 – 0 – +3 Determines the octave setting of the Arpeggio playback.
GateTime 0%–200% Determines the gate time of the Arpeggio notes.
BeatStretch 50, 66, 75, 100, 133, 150, 200%
Adjusts the tempo of the Arpeggio playback based on the current original
tempo. When “50%” is selected, for example, the playback time will be
halved (tempo is doubled). When “200%” is selected, on the other hand,
the playback time will be doubled (tempo is halved).
Swing -120% – 0% – +120% Adjusts the timing of the even-numbered back-beat notes of which the type is specified via the SwingValue parameter to produce a swing feel.
SwingValue
1/32 (32nd note), 3/16 (16th note
triplet, 1/16 (16th note), 3/8 (8th note
triplet), 1/8 (8th note), 3/4 (1/4 note
triplet, 1/4 (1/4 note)
Determines the type of note that serves as the basis for the Swing
parameter.
VelMode Orig, Thru
Determines how the velocities are applied to playback notes of the
selected Arpeggio type.
Orig..........The Arpeggio type is played back with the velocity values
preprogrammed in the Arpeggio sequence data.
Thru..........The Arpeggio type is played back with the velocity value
specified by pressing the key.Owner’s Manual
Using the KX with a DAW other than CubaseThe KX provides the setup templates which enable you to use the other DAW such as SONAR 5, Logic Pro7,
Digital Performer 5 as well as Cubase. If you want to use such a DAW, follow the procedure below:
1. Press the [UTILITY] button.
The LED lamp above the button lights and the
Utility display appears.
2. Use the SELECT buttons to call up “DAW
Select.”
3. Use the DATA [DEC] and [INC] buttons to
select one of the following DAW software
tools.
4. Press the [EXIT] button to return to the Top
display.
The setup has been completed.
To each DAW software, the following
operations are available.
Using the KX with a DAW other than Cubase
NOTE For details about the Remote Control settings, refer to the manual of the DAW software.
Settings DAW
LogicPro Apple Logic Pro
DigiPerf MOTU Digital Performer
SONAR Cakewalk Sonar
Button on the KX Operation
[ ] rewind
[ ] fast forward
[ ] Repeat On/Off
[■] stop
[ ] play
REC record
CUBASE FUNCTION [A] This button works the same as the F1 key on the Mackie Control.
CUBASE FUNCTION [B] This button works the same as the F2 key on the Mackie Control.
[ASSIGN 1] This button works the same as the F3 key on the Mackie Control.
[ASSIGN 2] This button works the same as the F4 key on the Mackie Control.
[MUTE] This button works the same as the F5 key on the Mackie Control.
[SOLO] This button works the same as the F6 key on the Mackie Control.
[VSTi WINDOW] This button works the same as the F7 key on the Mackie Control.
[ADD INSTRUMENT TRACK] This button works the same as the F8 key on the Mackie Control.
Program [DEC] Transmits the Program Change number decreased by 1 from the current number.
Program [INC] Transmits the Program Change number increased by 1 from the current number.
Cursor buttons This button works the same as the Cursor keys on your computer.
[ENTER] This button works the same as the Enter (Return) key on your computer.
[ESC] This button works the same as the Esc (esc) key on your computer.
NOTE If you perform the Remote Control setup for the Remote Control on the DAW software, you can perform
various operations by using the Cubase buttons such as the CUBASE FUNCTION [A] button and [ADD
INSTRUMENT TRACK] button. For instructions on assigning the function to the button, refer to the manual
of the DAW software.Owner’s Manual 31
Using the KX with a DAW other than Cubase
32MIDI ports on the KX
The KX provides the three MIDI ports and each of them can transmit/receive MIDI messages by using a
USB cable as described below:
USB MIDI Port 1 (KX-1): This port is used for communication of the performance data like note on/off
generated by playing the keyboard.
USB MIDI Port 2 (KX-2): This port is used for communication of data generated by controlling the
Transport function and the CONTROL knobs.
USB MIDI Port 3 (KX-3): This port is used for communication of data generated by controlling the KX
Editor.
NOTE · When the MIDI Select parameter is set to “MIDI” (page 34) resulting the USB TO HOST connector
becomes inactive, the data communication described above cannot be performed.
· When using the DAW software other than Cubase, perform the MIDI setup manually on the DAW
software so that the MIDI Port1 can handle the performance data like note on/off and the MIDI
Port2 can handle the data generated by controlling the Transport function.
· When using the DAW software other than Cubase, the MIDI Port2 cannot handle the data
generated by controlling the CONTROL knobs.
· When using a Macintosh computer, the MIDI Port is indicated with the name specified on the
“Audio MIDI Setup” window.Owner’s Manual
Using the KX with a DAW other than CubaseWhen using Digital Performer (Mark of the Unicorn Inc.) or Logic Pro
(Apple Inc.):
In each of these cases, you need to set the MIDI Port in the “Audio MIDI setup.”
1. In the start up disk of Mac OS X (normally named “Macintosh HD”), open “Application” then
“Utilities” and double click “Audio MIDI Setup”.
2. Click [MIDI Devices] if the [Audio Device] window is indicated.
The YAMAHA KX icon appears if the KX is recognized by the Macintosh computer.
3. Add three new external devices by clicking the [Add Device] icon three times.
Each “new external device” corresponds to each of the MIDI Ports in the KX. It is a good idea to
input your desired device name in the Properties of the new external device in order to easily
recognize the MIDI port later.
4. Connect the MIDI input/output plugs of the KX icon to the MIDI input/output plugs of the new
external device.
The MIDI input/output plugs of the KX icon correspond to the MIDI ports separately as follows:
Connect the plugs so that each port can handle MIDI messages.
YAMAHA KX YAMAHA KX Port1 (Left plug): MIDI Port 1
YAMAHA KX YAMAHA KX Port2 (Center plug): MIDI Port 2
NOTE YAMAHA KX YAMAHA KX Port3 (right most plug) used for data communication of the KX Editor is
not necessary to be set.Owner’s Manual 33
Utility Settings
34In the Utility display, you can make various settings such as the Arpeggio tempo, MIDI transmit/receive
settings, and display related settings.
Basic Operation
1. Press the [UTILITY] button.
The LED lamp above the button lights and the
Utility display appears.
2. Use the SELECT buttons to select the
parameter to be edited.
For details about parameters, refer to “Utility
Parameters” listed below.
3. Use the DATA [INC] and [DEC] buttons to
change the value.
4. After setting, press the [ENTER] button to
return to the Utility Top display.
The settings you made here will be stored
automatically without the special operation. The
settings will be maintained until executing the
Factory Set operation.
Utility Parameters
Utility Settings
NOTE If selecting “BulkTransmit” or “FactorySet”,
you can execute each of these functions by
pressing the DATA [INC] button.
Display Range
Initial
Value
Description
Tempo 10–300 120
Determines the tempo (BPM) of the Arpeggio playback. The
Arpeggio will play according to the speed of the MIDI clocks
transmitted from an external device or computer when the
Sync parameter is set to “Auto” (only when the MIDI clock is
transmitted continuously) or “External.”
Sync Auto, Internal, External Auto
Determines the tempo source transmitting the MIDI clocks
which the Arpeggio playback follows.
Auto............ When MIDI clock is transmitted continuously
from an external MIDI device or computer, the
internal clock of the KX is not effective and the
Arpeggio playback is synchronized with the
external clock. When MIDI clock is not
transmitted from the external MIDI device or
computer, the internal clock of the KX is effective
meaning that the Tempo value set on the KX is
available.
Internal ....... The Arpeggio will play with the Tempo value set
on the KX.
External ...... The Arpeggio will play according to the speed of
the MIDI clocks transmitted from an external
device or computer. When the KX does not
receive the MIDI clocks, the Arpeggio does not
play.
Clock Off, On On
Determines whether the tempo clock of the Arpeggio
playback is output as a MIDI message.
On .............. When this is selected, MIDI clocks will be
transmitted.
Off .............. When this is selected, MIDI clocks will not be
transmitted.
VeloCurve
Soft2, Soft1, Normal,
Hard1, Hard2, Fix
Normal
Determines the Velocity Curve. For information about each
value, see page 27.Owner’s Manual
Utility SettingsRestoring the Factory-programmed System (Factory Set)
You can restore the factory default settings of the
KX. Follow the instructions below to execute the
Factory Set.
CAUTION
• The edited Arpeggio types and Control Templates
will be lost by executing the Factory Set. Important
data should be saved to the computer by using the
KX Editor (page 6).
1. From the Top display, press the [UTILITY]
button so that its lamp lights.
2. Use the SELECT buttons to call up
“FactorySet.”
3. Press the DATA [INC] button.
“Are you sure?” appears on the display.
4. Press the DATA [INC] button again to
execute the Factory Set.
After the Factory Set has been completed, the
display called up in step 2 appears.
VeloFix 1–127 100
Determines the velocity value when the VelCurve is set to
“Fix.”.
DAW Select
CubaseAI, Cubase4,
LogicPro, DigiPerf,
SONAR
Cubase AI
Determines the DAW software you use on the computer with
the KX.
ProgChgMode
PC+Remot, ProgChg,
Remote
PC+Remot
Determines the type of the MIDI message generated by
pressing the PROGRAM [INC] and [DEC] buttons.
PC+Remot .... When this is selected, the Program Change
message is transmitted via the USB-MIDI Port1
and the Function message* of Mackie Control is
transmitted via the USB-MIDI Port2.
ProgChg..... When this is selected, the Program Change
message is transmitted via the USB=MIDI Port1.
Remote....... When this is selected, the Function message* of
Mackie Control is transmitted via the USB-MIDI
Port2.
* The “Function message” indicates that the message for the
Functions 9 or 10 of Mackie Control. The [DEC] button on
the KX corresponds to the Function 9 while the [INC]
button corresponds to the Function 10.
MIDI Select USB, MIDI USB
Determines the connector for MIDI data transmission/
reception.
MIDI Transmit Ch 01–16 01
Determines the MIDI channel over which the KX transmits
MIDI messages (generated via your keyboard performance).
MIDI In Thru
Off, MIDI Out, USB
Out
USB Out
Determines whether the MIDI messages received via the
MIDI IN connector will be transmitted via the MIDI OUT
connector or USB connector.
Device Number OFF, 1–16, All 10 Determines the MIDI Device Number of the KX.
Display Time
OFF, 1.0sec, 1.5sec,
2.0sec, 3.0sec,
4.0sec, 5.0sec, Hold
1.5sec
Determines the duration (time) for which the value (like the
one called up by operating the CONTROL knob) is shown
temporarily on the display.
Octave LED Normal, Reverse Normal
Determines the status of OCTAVE LED lamps. When “Normal”
is selected, the LED lamps work as described on page 27.
When “Reverse” is selected, the right and left of the LED
status are reversed.
BulkTransmit — —
Transmits all the settings of the KX to the DAW software or
external MIDI device as Bulk data. Press the DATA [INC]
button to start transmission.
FactorySet — — Restores the Factory-programmed System of the KX.
Display Range
Initial
Value
DescriptionOwner’s Manual 35
Utility Settings
36Setting the MIDI Thru parameter
With the initial default settings (MIDI Select = USB, MIDI Thru = MIDI → USB), MIDI messages received via
the MIDI IN connector of the KX will be transmitted through the USB TO HOST connector (USB MIDI Port1). As
necessary, you can change the MIDI Thru setting so that MIDI messages received via the MIDI IN connector
can be transmitted through the MIDI OUT connector, or the MIDI messages received via the USB TO HOST
connector (USB MIDI Port1) can be transmitted through the MIDI OUT connector.
1. Press the [UTILITY] button.
The LED lamp above the button lights and the
Utility display appears.
2. Use the SELECT [▲] and [▼] buttons to call
up the “MIDI Thru” parameter.
3. Use the DATA [DEC] and [INC] buttons to
select the desired value among the following
values.
4. After selecting, press the [EXIT] button to
return to the Top display.
Off
When this is selected, the MIDI Thru
function is not available, meaning that
MIDI messages received via the MIDI
IN or USB TO HOST connector will not
be transmitted through any connector.
MIDI → MIDI
When this is selected, MIDI messages
received via the MIDI IN connector will
be transmitted through the MIDI OUT
connector.
MIDI → USB
When this is selected, MIDI messages
received via the MIDI IN connector will
be transmitted through the USB TO
HOST connector (USB MIDI Port1).
USB → MIDI
When this is selected, MIDI messages
of USB MIDI Port1 received via the USB
TO HOST connector will be transmitted
through the MIDI OUT connector.
NOTE “MIDI → USB” and “USB → MIDI” can be
selected only when the MIDI Select
parameter is set to “USB” (page 34).Owner’s Manual
TroubleshootingThe power of the instrument does not turn on.
• When you do not connect the computer to the KX,
confirm whether or not the AC power adaptor is
properly plugged into the KX?
• When you do not use the AC power adaptor,
confirm whether or not a USB cable is properly
plugged into the KX and computer.
• Confirm whether not the USB hub with the buspowered type is used for connecting the KX and
computer. If you have to use the USB hub, use
the self-powered type or use the AC power
adaptor of the KX.
Communication problem between the computer
and the KX.
• Confirm whether or not a USB cable is properly
plugged into the KX and computer.
• Confirm whether or not the MIDI Select parameter
is set to “MIDI.” When using the KX and
computer, set MIDI Select parameter to “USB.”
DAW software on a computer cannot be
remotely controlled.
• Confirm whether or not the DAW software
specified as the DAW Select parameter on the
Utility display matches the DAW software you
actually use on your computer.
• Confirm whether or not the Remote Control
setting of the DAW software is proper. Refer to
the Owner’s Manual of each DAW software.
No sound of the software synthesizer like VSTi
on the computer is produced even if playing the
KX keyboard.
• Confirm whether or not a USB cable is properly
plugged into the KX and computer.
• Confirm whether or not the volume of the DAW
software or computer is set properly.
• Confirm whether or not the MIDI Select parameter
is set to “MIDI.” When using the KX and
computer, set MIDI Select parameter to “USB.”
• Confirm whether or not the Control Template
corresponding to the VSTi used on the computer
is selected currently on the KX. If not, call up the
corresponding Control Template. If the
corresponding Control Template is not provided
on the KX by default, create the Control Template
by using the KX Editor.
No sound of the MIDI tone generator connected
to the KX via a MIDI cable is produced even if
playing the KX keyboard.
• Confirm whether or not the MIDI cable is
connected properly.
• Confirm whether or not the MIDI Select parameter
is set to “USB.” When using the KX and MIDI
device, set MIDI Select parameter to “MIDI.”
The Arpeggiator does not play back with the
software synthesizer sound on the computer
connected to the KX via USB even if starting the
Arpeggiator on the KX.
• Confirm whether or not the Sync parameter of the
Utility display is set to “External.” If so, start
playback or recording on the DAW to transmit
MIDI clocks from the computer to the KX, or set
the Sync parameter to “Auto” or “Internal.”
Cubase does not recognize the KX.
• Confirm whether or not the “USB-MIDI Driver” and
“Extensions for Steinberg DAW” have been
installed. If not, install them.
• Confirm whether or not the KX is turned on before
starting Cubase. If not, do so.
Troubleshooting
NOTE Regarding the problems such as “No sound”
and “Noise sound,” refer to the
Troubleshooting in the manual of the DAW
software.Owner’s Manual 37
Message List
38Message List
LCD Indication Description
MIDI buffer full. Failed to process the MIDI data because too much data was received at one time.
MIDI checksum error. The check sum for the data received is incorrect.
MIDI data error. An error occurred when receiving MIDI data.
USB error. An error about the USB TO HOST connector occurred.
Keyboard error. An error about the keyboard occurred.
Memory error. An error about the memory for storing occurred.
Device number is off. The Device number is set to “off.”
Device number mismatch. The Device numbers do not match.
Executing... Displayed while the operation is being performed. Please wait.
Completed Displayed when the operation has been completed.
Template No.xx Displayed when the Control Template is selected automatically.
Are you sure? No→Dec/Yes→Inc
Prompts you to confirm whether or not you perform the operation. Pressing the [INC]
button performs the operation while pressing the [DEC] button to cancel the
operation.
Receiving MIDI bulk. The KX is receiving MIDI bulk data.Owner’s Manual
TOOLS for KX LICENSE AGREEMENTATTENTION
PLEASE READ THIS SOFTWARE LICENSE AGREEMENT (“AGREEMENT”) CAREFULLY BEFORE USING THIS SOFTWARE.
YOU ARE ONLY PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS
AGREEMENT. THIS AGREEMENT IS BETWEEN YOU (AS AN INDIVIDUAL OR LEGAL ENTITY) AND YAMAHA
CORPORATION (“YAMAHA”).
BY DOWNLOADING, INSTALLING, COPYING, OR OTHERWISE USING THIS SOFTWARE YOU ARE AGREEING TO BE
BOUND BY THE TERMS OF THIS LICENSE. IF YOU DO NOT AGREE WITH THE TERMS, DO NOT DOWNLOAD, INSTALL,
COPY, OR OTHERWISE USE THIS SOFTWARE. IF YOU HAVE DOWNLOADED OR INSTALLED THE SOFTWARE AND DO
NOT AGREE TO THE TERMS, PROMPTLY DELETE THE SOFTWARE.
1. GRANT OF LICENSE AND COPYRIGHT
Yamaha hereby grants you the right to use one copy of the
software program(s) and data (“SOFTWARE”)
accompanying this Agreement. The term SOFTWARE shall
encompass any updates to the accompanying software
and data. The SOFTWARE is owned by Yamaha and/or
Yamaha’s licensor(s), and is protected by relevant
copyright laws and all applicable treaty provisions. While
you are entitled to claim ownership of the data created with
the use of SOFTWARE, the SOFTWARE will continue to be
protected under relevant copyrights.
• You may use the SOFTWARE on a single computer.
• You may make one copy of the SOFTWARE in machinereadable form for backup purposes only, if the
SOFTWARE is on media where such backup copy is
permitted. On the backup copy, you must reproduce
Yamaha’s copyright notice and any other proprietary
legends that were on the original copy of the
SOFTWARE.
• You may permanently transfer to a third party all your
rights in the SOFTWARE, provided that you do not retain
any copies and the recipient reads and agrees to the
terms of this Agreement.
2. RESTRICTIONS
• You may not engage in reverse engineering,
disassembly, decompilation or otherwise deriving a
source code form of the SOFTWARE by any method
whatsoever.
• You may not reproduce, modify, change, rent, lease, or
distribute the SOFTWARE in whole or in part, or create
derivative works of the SOFTWARE.
• You may not electronically transmit the SOFTWARE from
one computer to another or share the SOFTWARE in a
network with other computers.
• You may not use the SOFTWARE to distribute illegal
data or data that violates public policy.
• You may not initiate services based on the use of the
SOFTWARE without permission by Yamaha Corporation.
Copyrighted data, including but not limited to MIDI data
for songs, obtained by means of the SOFTWARE, are
subject to the following restrictions which you must
observe.
• Data received by means of the SOFTWARE may not be
used for any commercial purposes without permission of
the copyright owner.
• Data received by means of the SOFTWARE may not be
duplicated, transferred, or distributed, or played back or
performed for listeners in public without permission of
the copyright owner.
• The encryption of data received by means of the
SOFTWARE may not be removed nor may the electronic
watermark be modified without permission of the
copyright owner.
3. TERMINATION
This Agreement becomes effective on the day that you
receive the SOFTWARE and remains effective until
terminated. If any copyright law or provisions of this
Agreement is violated, the Agreement shall terminate
automatically and immediately without notice from
Yamaha. Upon such termination, you must immediately
destroy the licensed SOFTWARE, any accompanying
written documents and all copies thereof.
4. DISCLAIMER OF WARRANTY ON SOFTWARE
You expressly acknowledge and agree that use of the
SOFTWARE is at your sole risk. The SOFTWARE and
related documentation are provided “AS IS” and without
warranty of any kind. NOTWITHSTANDING ANY OTHER
PROVISION OF THIS AGREEMENT, YAMAHA EXPRESSLY
DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE,
EXPRESS, AND IMPLIED, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NON-
INFRINGEMENT OF THIRD PARTY RIGHTS.
SPECIFICALLY, BUT WITHOUT LIMITING THE
FOREGOING, YAMAHA DOES NOT WARRANT THAT THE
SOFTWARE WILL MEET YOUR REQUIREMENTS, THAT
THE OPERATION OF THE SOFTWARE WILL BE
UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS
IN THE SOFTWARE WILL BE CORRECTED.
5. LIMITATION OF LIABILITY
YAMAHA’S ENTIRE OBLIGATION HEREUNDER SHALL BE
TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS
HEREOF. IN NO EVENT SHALL YAMAHA BE LIABLE TO
YOU OR ANY OTHER PERSON FOR ANY DAMAGES,
INCLUDING, WITHOUT LIMITATION, ANY DIRECT,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR
OTHER DAMAGES ARISING OUT OF THE USE, MISUSE
OR INABILITY TO USE THE SOFTWARE, EVEN IF
YAMAHA OR AN AUTHORIZED DEALER HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. In
no event shall Yamaha’s total liability to you for all
damages, losses and causes of action (whether in
contract, tort or otherwise) exceed the amount paid for the
SOFTWARE.
TOOLS for KX LICENSE AGREEMENTOwner’s Manual 39
Cubase AI4 LICENSE AGREEMENT
406. THIRD PARTY SOFTWARE
Third party software and data (“THIRD PARTY
SOFTWARE”) may be attached to the SOFTWARE. If, in the
written materials or the electronic data accompanying the
Software, Yamaha identifies any software and data as
THIRD PARTY SOFTWARE, you acknowledge and agree
that you must abide by the provisions of any Agreement
provided with the THIRD PARTY SOFTWARE and that the
party providing the THIRD PARTY SOFTWARE is
responsible for any warranty or liability related to or arising
from the THIRD PARTY SOFTWARE. Yamaha is not
responsible in any way for the THIRD PARTY SOFTWARE
or your use thereof.
• Yamaha provides no express warranties as to the THIRD
PARTY SOFTWARE. IN ADDITION, YAMAHA
EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, as to the THIRD PARTY
SOFTWARE.
• Yamaha shall not provide you with any service or
maintenance as to the THIRD PARTY SOFTWARE.
• Yamaha is not liable to you or any other person for any
damages, including, without limitation, any direct,
indirect, incidental or consequential damages,
expenses, lost profits, lost data or other damages
arising out of the use, misuse or inability to use the
THIRD PARTY SOFTWARE.
7. GENERAL
This Agreement shall be interpreted according to and
governed by Japanese law without reference to principles
of conflict of laws. Any dispute or procedure shall be heard
before the Tokyo District Court in Japan. If for any reason a
court of competent jurisdiction finds any portion of this
Agreement to be unenforceable, the remainder of this
Agreement shall continue in full force and effect.
8. COMPLETE AGREEMENT
This Agreement constitutes the entire agreement between
the parties with respect to use of the SOFTWARE and any
accompanying written materials and supersedes all prior
or contemporaneous understandings or agreements,
written or oral, regarding the subject matter of this
Agreement. No amendment or revision of this Agreement
will be binding unless in writing and signed by a fully
authorized representative of Yamaha.
ATTENTION
PLEASE READ THIS SOFTWARE LICENSE AGREEMENT (“AGREEMENT”) CAREFULLY BEFORE USING THIS SOFTWARE.
YOU ARE ONLY PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS
AGREEMENT. THIS AGREEMENT IS BETWEEN YOU (AS AN INDIVIDUAL OR LEGAL ENTITY) AND YAMAHA
CORPORATION (“YAMAHA”).
BY BREAKING THE SEAL OF THIS PACKAGE YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. IF
YOU DO NOT AGREE WITH THE TERMS, DO NOT INSTALL, COPY, OR OTHERWISE USE THIS SOFTWARE.
THIS AGREEMENT PROVIDES YOUR USE-CONDITIONS ABOUT THE “DAW” SOFTWARE OF STEINBERG MEDIA
TECHNOLOGIES GMBH(“STEINBERG”) WHICH IS BUNDLED WITH THIS PRODUCT. SINCE THE END-USER SOFTWARE
LICENSE AGREEMENT (EUSLA) SHOWN ON YOUR PC-DISPLAY IN YOUR INSTALLING THE “DAW” SOFTWARE IS
REPLACED BY THIS AGREEMENT, YOU SHOULD DISREGARD THE EUSLA. THAT IS, IN THE INSTALLING PROCESS, YOU
SHOULD SELECT “AGREE” WITH THE EUSLA, WITHOUT YOUR JUDGMENT THERETO, SO AS TO PROCEED TO THE
NEXT PAGE.
1. GRANT OF LICENSE AND COPYRIGHT
Yamaha hereby grants you the right to use one copy of the
software program(s) and data (“SOFTWARE”)
accompanying this Agreement. The term SOFTWARE shall
encompass any updates to the accompanying software
and data. The SOFTWARE is owned by STEINBERG, and
is protected by relevant copyright laws and all applicable
treaty provisions. Yamaha has acquired the sublicense
right to license you to use the SOFTWARE. While you are
entitled to claim ownership of the data created with the use
of SOFTWARE, the SOFTWARE will continue to be
protected under relevant copyrights.
You may use the SOFTWARE on a single computer.
You may make one copy of the SOFTWARE in machinereadable form for backup purposes only, if the SOFTWARE
is on media where such backup copy is permitted. On the
backup copy, you must reproduce Yamaha’s copyright
notice and any other proprietary legends that were on the
original copy of the SOFTWARE.
You may permanently transfer to a third party all your rights
in the SOFTWARE only when you transfer this product
together, provided that you do not retain any copies and
the recipient reads and agrees to the terms of this
Agreement.
2. RESTRICTIONS
You may not engage in reverse engineering, disassembly,
decompilation or otherwise deriving a source code form of
the SOFTWARE by any method whatsoever.
You may not reproduce, modify, change, rent, lease, or
distribute the SOFTWARE in whole or in part, or create
derivative works of the SOFTWARE.
You may not electronically transmit the SOFTWARE from
one computer to another or share the SOFTWARE in a
network with other computers.
You may not use the SOFTWARE to distribute illegal data
or data that violates public policy.
You may not initiate services based on the use of the
SOFTWARE without permission by Yamaha Corporation.
Cubase AI4 LICENSE AGREEMENTOwner’s Manual
Cubase AI4 LICENSE AGREEMENTCopyrighted data, including but not limited to MIDI data for
songs, obtained by means of the SOFTWARE, are subject
to the following restrictions which you must observe.
Data received by means of the SOFTWARE may not be
used for any commercial purposes without permission of
the copyright owner.
Data received by means of the SOFTWARE may not be
duplicated, transferred, or distributed, or played back or
performed for listeners in public without permission of the
copyright owner.
The encryption of data received by means of the
SOFTWARE may not be removed nor may the electronic
watermark be modified without permission of the copyright
owner.
3. TERMINATION
This Agreement becomes effective on the day that you
receive the SOFTWARE and remains effective until
terminated. If any copyright law or provisions of this
Agreement is violated, the Agreement shall terminate
automatically and immediately without notice from
Yamaha. Upon such termination, you must immediately
destroy the licensed SOFTWARE, any accompanying
written documents and all copies thereof.
4. LIMITED WARRANTY ON MEDIA
As to SOFTWARE sold on tangible media, Yamaha
warrants that the tangible media on which the SOFTWARE
is recorded will be free from defects in materials and
workmanship under normal use for a period of fourteen
(14) days from the date of receipt, as evidenced by a copy
of the receipt. Yamaha’s entire liability and your exclusive
remedy will be replacement of the defective media if it is
returned to Yamaha or an authorized Yamaha dealer within
fourteen days with a copy of the receipt. Yamaha is not
responsible for replacing media damaged by accident,
abuse or misapplication. TO THE FULLEST EXTENT
PERMITTED BY LAW, YAMAHA EXPRESSLY DISCLAIMS
ANY IMPLIED WARRANTIES ON THE TANGIBLE MEDIA,
INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
5. DISCLAIMER OF WARRANTY ON SOFTWARE
You expressly acknowledge and agree that use of the
SOFTWARE is at your sole risk. The SOFTWARE and
related documentation are provided “AS IS” and without
warranty of any kind. NOTWITHSTANDING ANY OTHER
PROVISION OF THIS AGREEMENT, YAMAHA EXPRESSLY
DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE,
EXPRESS, AND IMPLIED, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NON-
INFRINGEMENT OF THIRD PARTY RIGHTS.
SPECIFICALLY, BUT WITHOUT LIMITING THE
FOREGOING, YAMAHA DOES NOT WARRANT THAT THE
SOFTWARE WILL MEET YOUR REQUIREMENTS, THAT
THE OPERATION OF THE SOFTWARE WILL BE
UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS
IN THE SOFTWARE WILL BE CORRECTED.
6. LIMITATION OF LIABILITY
YAMAHA’S ENTIRE OBLIGATION HEREUNDER SHALL BE
TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS
HEREOF. IN NO EVENT SHALL YAMAHA BE LIABLE TO
YOU OR ANY OTHER PERSON FOR ANY DAMAGES,
INCLUDING, WITHOUT LIMITATION, ANY DIRECT,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR
OTHER DAMAGES ARISING OUT OF THE USE, MISUSE
OR INABILITY TO USE THE SOFTWARE, EVEN IF
YAMAHA OR AN AUTHORIZED DEALER HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. In
no event shall Yamaha’s total liability to you for all
damages, losses and causes of action (whether in
contract, tort or otherwise) exceed the amount paid for the
SOFTWARE.
7. GENERAL
This Agreement shall be interpreted according to and
governed by Japanese law without reference to principles
of conflict of laws. Any dispute or procedure shall be heard
before the Tokyo District Court in Japan. If for any reason a
court of competent jurisdiction finds any portion of this
Agreement to be unenforceable, the remainder of this
Agreement shall continue in full force and effect.
8. COMPLETE AGREEMENT
This Agreement constitutes the entire agreement between
the parties with respect to use of the SOFTWARE and any
accompanying written materials and supersedes all prior
or contemporaneous understandings or agreements,
written or oral, regarding the subject matter of this
Agreement. No amendment or revision of this Agreement
will be binding unless in writing and signed by a fully
authorized representative of Yamaha. Owner’s Manual 41
Appendix
42Specifications
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right
to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options
may not be the same in every locale, please check with your Yamaha dealer.
Appendix
Keyboard
KX25 25 keys (Initial Touch)
KX49 49 keys (Initial Touch)
KX61 61 keys (Initial Touch)
Sequencer block Arpeggiator approximately 300 types
Remote Control block DAW
For Windows: Cubase 4, SONAR 5.2
For Macintosh: Cubase 4, Logic 7.2, Digital Performer 5.1
* Functions to be controlled differ depending on the software.
Controller
Pitch Bend Wheel x 1
Modulation Wheel x 1
CONTROL knobs x 4 (assignable)
Display 16 characters x 2 lines LED lamp with the back light
Connectors
USB (TO HOST)
MIDI IN/OUT
DC-IN
FOOT SWITCH (SUSTAIN)
Power Consumption
??? W (when using the AC power adaptor)
??? W (when using this product as a bus-powered device)
Dimensions, weight
KX25: XXXX
KX49: XXXX
KX61: XXXX
Accessories
AC power adaptor (PA-3C, PA-130, or an equivalent)
USB cable, Discs x 2, Owner’s Manual (this book)Owner’s Manual
AppendixControl Template List
About what function is assigned to each knob when each Template is selected, refer to the following page:
http://www.yamahasynth.com/
No. Manufacturer Product name Indication on the KX display
1 Steinberg HALion One HALionOne
2 Mystic Mystic
3 Prologue Prologue
4 Spector Spector
5 Embracer Embracer
6 Monologue Monologue
7 Hypersonic2 Hypersonic
8 HALion3 HALion
9 Native Instruments PRO-53 Pro-53
10 FM8 FM8
11 MASSIVE Massive
12 KORG Polysix Polysix
13 WAVESTATION Wavestation
14 Mono/Poly MonoPoly
15 M1 M1
16 MS-20 MS-20
17 M-AUDIO / GForce impOSCar impOSCar
18 Minimonsta Minimonsta
19 Oddity Oddity
20 Arturia Analog Factory AnalogFactory
21 CS-80V CS-80V
22 Jupiter-8V Jupiter-8V
23 Minimoog V Minimoog V
24 Novation Music V-Station V-Station
25 Bass Station BassStation
26 reFX VANGUARD Vanguard
27 IK Multimedia SampleTank2 SampleTank
28 Spectrasonics ATMOSPHERE Atmosphere
29 TRILOGY Trilogy
30 -- -- GenericOwner’s Manual 43
Appendix
44Arpeggio Type List
General Voice types which can be selected on HALionOne and are most suitable for the respective Arpeggio
Types are listed in the “Voice Type” column.
Category Arp. No.
Arp.
Name
Time
Signature Length
Original
Tempo Voice Type
DrPc 1 ContmpRk 4 / 4 4 126 Stereo GM
DrPc 2 StndRock 4 / 4 4 131 :
DrPc 3 PowerRck 4 / 4 4 120 :
DrPc 4 AlternRk 4 / 4 4 100 RockSt2
DrPc 5 MondoRck 4 / 4 4 94 :
DrPc 6 XoverRk 4 / 4 2 100 :
DrPc 7 Rck&Roll 4 / 4 4 172 Stereo GM
DrPc 8 GuitrPp1 4 / 4 2 90 :
DrPc 9 GuitrPp2 4 / 4 4 100 :
DrPc 10 Unpluggd 4 / 4 4 120 :
DrPc 11 FingrPck 4 / 4 4 94 :
DrPc 12 Brit Pop 4 / 4 2 86 :
DrPc 13 EP Balld 4 / 4 2 60 :
DrPc 14 8BtBasic 4 / 4 4 120 :
DrPc 15 8Bt Soft 4 / 4 4 100 :
DrPc 16 16BtBld1 4 / 4 4 75 :
DrPc 17 16BtBld2 4 / 4 2 64 :
DrPc 18 16Bt Pop 4 / 4 4 103 :
DrPc 19 6/8 Pop 4 / 4 4 100 :
DrPc 20 6/8Balld 4 / 4 2 58 :
DrPc 21 Funk 4 / 4 4 107 :
DrPc 22 FunkRock 4 / 4 4 95 :
DrPc 23 JazzFunk 4 / 4 4 120 :
DrPc 24 SlowEasy 4 / 4 4 72 :
DrPc 25 ClubJazz 4 / 4 4 125 :
DrPc 26 PopShuff 4 / 4 4 94 :
DrPc 27 GosplFnk 4 / 4 4 106 :
DrPc 28 StdDisco 4 / 4 4 120 :
DrPc 29 PhilyDsc 4 / 4 2 100 :
DrPc 30 ChartPop 4 / 4 4 92 Hip Hop 1
DrPc 31 New R&B 4 / 4 1 97 :
DrPc 32 Smooth 4 / 4 4 64 :
DrPc 33 HipHop1 4 / 4 2 94 :
DrPc 34 HipHop2 4 / 4 2 105 :
DrPc 35 HipHop3 4 / 4 2 104 R&B Kit 1
DrPc 36 Hip Rock 4 / 4 4 132 :
DrPc 37 Regeton 4 / 4 4 98 Hip Hop 1
DrPc 38 RegetnPc 4 / 4 4 98 Perccussion
DrPc 39 SoulBeat 4 / 4 4 124 Stereo GM
DrPc 40 SoulShuf 4 / 4 4 98 :
DrPc 41 Big Beat 4 / 4 4 115 RockSt2
DrPc 42 Breakbt 4 / 4 4 115 Tekno Kit
DrPc 43 Lo Beat 4 / 4 2 140 R&B Kit 1
DrPc 44 DrumnBas 4 / 4 2 154 :
DrPc 45 Techno 4 / 4 8 135 Tekno Kit
DrPc 46 Trance 4 / 4 4 140 :
DrPc 47 DreamDnc 4 / 4 4 136 :
DrPc 48 Ibiza 4 / 4 2 135 R&B Kit 1
DrPc 49 EuroTeck 4 / 4 2 140 Tekno Kit
DrPc 50 Club Hus 4 / 4 2 128 R&B Kit 1
DrPc 51 House 4 / 4 2 123 :
DrPc 52 Garage 4 / 4 2 127 Tekno Kit
DrPc 53 AcoJazz 4 / 4 4 204 Jazz Kit
DrPc 54 ModernJz 4 / 4 16 218 :
DrPc 55 ShfBlues 4 / 4 4 115 Stereo GM
DrPc 56 SlwBlues 4 / 4 2 49 :
DrPc 57 PnBoogie 4 / 4 8 160 :
DrPc 58 Reggae 4 / 4 4 102 :
DrPc 59 ReggeShf 4 / 4 4 90 :
DrPc 60 Salsa 4 / 4 2 123 :
DrPc 61 SalsaPc 4 / 4 4 123 :
DrPc 62 Samba 4 / 4 4 120 :
DrPc 63 SambaPc 4 / 4 4 120 :
DrPc 64 Bossa 4 / 4 4 124 :
DrPc 65 BossaPc 4 / 4 4 124 :
DrPc 66 Spanish 4 / 4 2 120 :
CPrc 67 R&B Dsc 4 / 4 2 110 Vibes
CPrc 68 Trance 4 / 4 4 140 Marimba
CPrc 69 Ethnic1 6 / 4 5 118 Celeste
CPrc 70 Ethnic2 7 / 4 3 120 Music Box
CPrc 71 MOD 4 / 4 2 120 Glocken
CPrc 72 Trill 4 / 4 1 120 Marimba
Bass 73 CntmpRk1 4 / 4 4 126 Pick Bass
Bass 74 CntmpRk2 4 / 4 4 126 :
Bass 75 StndRck1 4 / 4 4 131 FingerBass
Bass 76 StndRck2 4 / 4 4 131 :
Bass 77 PowerRk1 4 / 4 4 120 Pick Bass
Bass 78 PowerRk2 4 / 4 4 120 :
Bass 79 AlternRk 4 / 4 4 100 FingerBass
Bass 80 XoverRk 4 / 4 1 100 :
Bass 81 Rck&Roll 4 / 4 4 172 Pick Bass
Bass 82 GuitrPp1 4 / 4 2 90 FingerBass
Bass 83 GuitrPp2 4 / 4 4 100 Pick Bass
Bass 84 Unpluggd 4 / 4 4 113 Acoustic
Bass 85 FingrPck 4 / 4 1 120 FingerBass
Bass 86 Brit Pop 4 / 4 2 86 :
Bass 87 EP Balld 4 / 4 2 60 :
Bass 88 8BtBasic 4 / 4 4 120 :
Bass 89 8BtSoft 4 / 4 4 100 :
Bass 90 16BtBlld 4 / 4 4 75 :
Bass 91 16Bt Pop 4 / 4 4 103 SimpleSlap
Bass 92 6/8 Pop 4 / 4 4 100 FingerBass
Bass 93 6/8Balld 4 / 4 2 58 :
Bass 94 FingrBs1 4 / 4 1 115 :
Bass 95 FingrBs2 4 / 4 3 115 :
Bass 96 FingrBs3 4 / 4 2 150 :
Bass 97 FingrBs4 4 / 4 2 89 :
Bass 98 FingrBs5 4 / 4 1 115 :
Bass 99 SlapBass 4 / 4 3 120 SimpleSlap
Bass 100 FunkRock 4 / 4 4 95 FingerBass
Category Arp. No.
Arp.
Name
Time
Signature Length
Original
Tempo Voice TypeOwner’s Manual
AppendixBass 101 JazFunk1 4 / 4 2 120 :
Bass 102 JazFunk2 4 / 4 4 120 :
Bass 103 SlowEasy 4 / 4 4 72 :
Bass 104 ClubJazz 4 / 4 4 125 :
Bass 105 PopShuff 4 / 4 4 94 Velo Slap
Bass 106 GosplFnk 4 / 4 4 106 FingerBass
Bass 107 StdDisco 4 / 4 1 120 :
Bass 108 PhilyDsc 4 / 4 2 100 :
Bass 109 ChartPop 4 / 4 4 92 SynthBass2
Bass 110 NewR&B1 4 / 4 1 97 :
Bass 111 NewR&B2 4 / 4 1 97 :
Bass 112 Smooth 4 / 4 2 64 :
Bass 113 HipHop1 4 / 4 2 105 :
Bass 114 HipHop2 4 / 4 2 94 :
Bass 115 HipHop3 4 / 4 2 94 :
Bass 116 HipHop4 4 / 4 2 94 :
Bass 117 Hip Rock 4 / 4 4 132 FingerBass
Bass 118 Regeton 4 / 4 4 98 SynthBass1
Bass 119 GruvBass 4 / 4 2 120 SynthBass2
Bass 120 SoulBeat 4 / 4 4 124 FingerBass
Bass 121 SoulShuf 4 / 4 4 98 :
Bass 122 ChillOut 4 / 4 2 79 :
Bass 123 Big Beat 4 / 4 4 115 :
Bass 124 Breakbt1 4 / 4 4 115 SynthBass1
Bass 125 Breakbt2 4 / 4 4 88 SynthBass2
Bass 126 DrumnBas 4 / 4 4 170 :
Bass 127 Techno 4 / 4 8 135 :
Bass 128 Trance 4 / 4 4 140 :
Bass 129 Tek Bass 4 / 4 1 138 :
Bass 130 DreamDnc 4 / 4 2 136 :
Bass 131 Ibiza 4 / 4 2 135 :
Bass 132 DiscoHus 4 / 4 4 126 :
Bass 133 ClubHus1 4 / 4 1 128 :
Bass 134 ClubHus2 4 / 4 1 128 :
Bass 135 Garage 4 / 4 2 127 :
Bass 136 HouseBas 4 / 4 4 120 :
Bass 137 AcidBass 4 / 4 1 120 :
Bass 138 AcoJazz1 4 / 4 4 204 Acoustic
Bass 139 AcoJazz2 4 / 4 4 204 :
Bass 140 ModrnJz1 4 / 4 16 218 :
Bass 141 ModrnJz2 4 / 4 16 218 :
Bass 142 ShfBlues 4 / 4 4 115 Pick Bass
Bass 143 SlwBlues 4 / 4 2 49 FingerBass
Bass 144 PnBoogie 4 / 4 8 160 Acoustic
Bass 145 Reggae 4 / 4 4 102 FingerBass
Bass 146 ReggeShf 4 / 4 4 90 :
Bass 147 Salsa 4 / 4 4 123 Acoustic
Bass 148 Montuno 4 / 4 4 100 FingerBass
Bass 149 Samba 4 / 4 2 120 :
Bass 150 Bossa 4 / 4 4 124 :
Bass 151 LatinHus 4 / 4 4 138 :
Bass 152 Spanish 4 / 4 1 120 :
Seq 153 Classic 4 / 4 1 120 Saw Ld
Seq 154 Oct Seq 4 / 4 1 130 Bass&Ld
Seq 155 RandmSeq 4 / 4 1 90 Sci-Fi
Category Arp. No.
Arp.
Name
Time
Signature Length
Original
Tempo Voice Type
Seq 156 Vel Gruv 4 / 4 1 134 Saw Ld
Seq 157 X-Sweep 4 / 4 1 140 :
Seq 158 Simple1 4 / 4 1 130 Chiff Ld
Seq 159 Simple2 4 / 4 1 130 :
Seq 160 Simple3 4 / 4 1 130 :
Seq 161 Basic 4 / 4 1 130 Brightness
Seq 162 FifthSQ1 4 / 4 1 130 5th Ld
Seq 163 FifthSQ2 4 / 4 1 130 :
Seq 164 MuteLine 4 / 4 1 134 Saw Ld
Seq 165 Chodal 4 / 4 2 150 :
Seq 166 AlternRk 4 / 4 4 100 Charan Ld
Seq 167 Trance1 4 / 4 4 115 Chiff Ld
Seq 168 Trance2 4 / 4 1 140 Poly Synth
Seq 169 Trance3 4 / 4 4 140 :
Seq 170 Trance4 4 / 4 1 140 Square Ld
Seq 171 Trance5 4 / 4 1 140 :
Seq 172 Trance6 4 / 4 4 140 Bass&Ld
Seq 173 Trance7 4 / 4 1 140 Poly Synth
Seq 174 Trance8 4 / 4 1 130 :
Seq 175 Trance9 4 / 4 2 145 :
Seq 176 Trance10 4 / 4 2 145 :
Seq 177 DreamDnc 4 / 4 1 136 Square Ld
Seq 178 Ibiza1 4 / 4 2 135 Charan Ld
Seq 179 Ibiza2 4 / 4 2 135 Square Ld
Seq 180 Tekno 4 / 4 2 120 Saw Ld
Seq 181 SynArp1 4 / 4 1 130 :
Seq 182 SynArp2 4 / 4 1 130 :
Seq 183 SynArp3 4 / 4 1 130 :
Seq 184 SynArp4 4 / 4 1 90 :
Seq 185 SynArp5 4 / 4 1 138 :
Seq 186 Melody1 4 / 4 1 70 Brightness
Seq 187 Melody2 4 / 4 1 70 :
Seq 188 Electro1 4 / 4 1 130 Saw Ld
Seq 189 Electro2 4 / 4 1 130 :
Seq 190 Electro3 4 / 4 1 130 :
Seq 191 Electro4 4 / 4 1 130 :
Seq 192 Electro5 4 / 4 1 130 :
Seq 193 Electro6 4 / 4 1 130 :
Seq 194 CompuBas 4 / 4 1 130 Bass&Ld
Seq 195 Poly Arp 4 / 4 1 120 Saw Ld
Seq 196 Tek Echo 4 / 4 2 120 :
Seq 197 SuperArp 4 / 4 2 120 :
Seq 198 AcidLine 4 / 4 1 120 :
Seq 199 Doves 4 / 4 1 150 :
Seq 200 PulsLine 4 / 4 2 120 :
Seq 201 SyncpEco 4 / 4 2 120 Poly Synth
Seq 202 Waggle 4 / 4 1 140 Saw Ld
ChSq 203 SynChrd1 4 / 4 1 130 Poly Synth
ChSq 204 SynChrd2 4 / 4 1 90 Bass&Ld
ChSq 205 BasChrd1 4 / 4 2 130 :
ChSq 206 BasChrd2 4 / 4 1 130 :
ChSq 207 ChillChd 4 / 4 1 90 Poly Synth
ChSq 208 TrancRtm 4 / 4 4 140 :
ChSq 209 Ibiza 4 / 4 2 135 Bass&Ld
ChSq 210 Garage 4 / 4 2 127 :
Category Arp. No.
Arp.
Name
Time
Signature Length
Original
Tempo Voice TypeOwner’s Manual 45
Appendix
46ChSq 211 Syncopat 4 / 4 2 120 Saw Ld
HySq 212 Hybrid1 4 / 4 1 130 :
HySq 213 Hybrid2 4 / 4 1 95 :
HySq 214 Hybrid3 4 / 4 1 130 :
HySq 215 Hybrid4 4 / 4 1 130 Bass&Ld
HySq 216 Hybrid5 4 / 4 1 106 :
ApKb 217 Pf Arp1 4 / 4 2 64 Acoustic Piano
ApKb 218 Pf Arp2 4 / 4 2 74 :
ApKb 219 Pf Arp3 4 / 4 2 130 :
ApKb 220 Pf Arp4 4 / 4 1 116 :
ApKb 221 Pf Arp5 4 / 4 1 82 :
ApKb 222 Pf Arp6 4 / 4 2 130 :
ApKb 223 Pf Arp7 4 / 4 2 130 :
ApKb 224 Pf Arp8 4 / 4 1 74 :
ApKb 225 70sRock1 4 / 4 2 130 :
ApKb 226 70sRock2 4 / 4 4 130 :
ApKb 227 EP Balld 4 / 4 2 60 E_Piano 1
ApKb 228 Slowfeel 4 / 4 1 74 :
ApKb 229 16Bt Pop 4 / 4 4 103 :
ApKb 230 AnalgPop 4 / 4 2 93 :
ApKb 231 ClubJazz 4 / 4 4 125 Acoustic Piano
ApKb 232 ChartPop 4 / 4 1 92 E_Piano 1
ApKb 233 Swing EP 4 / 4 1 101 :
ApKb 234 6/8 R&B 4 / 4 2 61 :
ApKb 235 HipHop1 4 / 4 2 105 :
ApKb 236 HipHop2 4 / 4 2 105 :
ApKb 237 HipHop3 4 / 4 2 105 Harpsichord
ApKb 238 Clavi1 4 / 4 1 110 Brite Clav
ApKb 239 Clavi2 4 / 4 1 110 :
ApKb 240 Clavi3 4 / 4 1 124 :
ApKb 241 DrumnBas 4 / 4 4 170 E_Piano 1
ApKb 242 ClubHus 4 / 4 2 128 :
ApKb 243 HousePf 4 / 4 2 130 Rock Piano
ApKb 244 Reggae 4 / 4 2 92 Brite Clav
ApKb 245 Salsa 4 / 4 1 123 Rock Piano
ApKb 246 Montuno 4 / 4 2 100 :
ApKb 247 PnoLatin 4 / 4 2 120 :
Orgn 248 HouseOrg 4 / 4 1 130 Perc Organ
Orgn 249 Reggae 4 / 4 1 92 Draw Organ
Orgn 250 LatinOrg 4 / 4 1 110 Rock Organ
GtPl 251 Strum1 4 / 4 2 120 Steel
GtPl 252 Strum2 4 / 4 2 120 :
GtPl 253 Strum3 4 / 4 2 120 :
GtPl 254 SteelGtr 4 / 4 4 120 :
GtPl 255 GtrArp1 4 / 4 1 120 :
GtPl 256 GtrArp2 4 / 4 1 120 :
GtPl 257 OvdrGtr1 4 / 4 4 120 Overdrive
GtPl 258 OvdrGtr2 4 / 4 4 120 :
GtPl 259 OvdrGtr3 4 / 4 4 120 :
GtPl 260 OvdrGtr4 4 / 4 4 120 :
GtPl 261 ContmpRk 4 / 4 4 126 :
GtPl 262 StndRck1 4 / 4 4 131 :
GtPl 263 StndRck2 4 / 4 4 131 :
GtPl 264 PowerRk1 4 / 4 4 120 Distortion
GtPl 265 PowerRk2 4 / 4 4 120 :
Category Arp. No.
Arp.
Name
Time
Signature Length
Original
Tempo Voice Type
GtPl 266 PowerRk3 4 / 4 4 120 :
GtPl 267 AlterRk1 4 / 4 4 97 Overdrive
GtPl 268 AlterRk2 4 / 4 4 97 :
GtPl 269 XoverRk1 4 / 4 2 100 :
GtPl 270 XoverRk2 4 / 4 2 100 Distortion
GtPl 271 Rck&Roll 4 / 4 4 172 Clean
GtPl 272 GuitrPp1 4 / 4 2 90 Nylon
GtPl 273 GuitrPp2 4 / 4 1 90 :
GtPl 274 GuitrPp3 4 / 4 4 100 Steel
GtPl 275 GuitrPp4 4 / 4 4 100 Clean
GtPl 276 GuitrPp5 4 / 4 1 90 Nylon
GtPl 277 Unplug1 4 / 4 4 120 Steel
GtPl 278 Unplug2 4 / 4 2 120 :
GtPl 279 Unplug3 4 / 4 2 120 :
GtPl 280 FingrPk1 4 / 4 2 120 :
GtPl 281 FingrPk2 4 / 4 2 120 :
GtPl 282 BritPop1 4 / 4 2 86 :
GtPl 283 BritPop2 4 / 4 2 86 Clean
GtPl 284 EP Balld 4 / 4 2 60 :
GtPl 285 8BtBasic 4 / 4 4 120 :
GtPl 286 8BtSoft 4 / 4 4 100 Steel
GtPl 287 16BtBlld 4 / 4 4 75 Clean
GtPl 288 6/8 Pop 4 / 4 4 100 :
GtPl 289 6/8Balld 4 / 4 2 58 :
GtPl 290 Funky1 4 / 4 2 120 :
GtPl 291 Funky2 4 / 4 2 120 :
GtPl 292 Funky3 4 / 4 1 120 :
GtPl 293 CleanGt1 4 / 4 4 107 :
GtPl 294 CleanGt2 4 / 4 2 120 :
GtPl 295 CleanGt3 4 / 4 2 120 :
GtPl 296 CleanGt4 4 / 4 4 127 :
GtPl 297 CleanGt5 4 / 4 4 107 :
GtPl 298 Spanky 4 / 4 2 105 :
GtPl 299 FunkRock 4 / 4 4 94 :
GtPl 300 JazzFunk 4 / 4 4 120 :
GtPl 301 SlowEasy 4 / 4 4 72 :
GtPl 302 GosplFnk 4 / 4 4 106 :
GtPl 303 PopShuff 4 / 4 4 94 :
GtPl 304 StdDisco 4 / 4 4 120 :
GtPl 305 PhilyDsc 4 / 4 2 100 :
GtPl 306 New R&B 4 / 4 1 97 Steel
GtPl 307 Smooth 4 / 4 2 64 Nylon
GtPl 308 HipHop1 4 / 4 2 94 Mute
GtPl 309 HipHop2 4 / 4 2 94 :
GtPl 310 HipRock1 4 / 4 4 90 Overdrive
GtPl 311 HipRock2 4 / 4 4 132 :
GtPl 312 SoulBeat 4 / 4 4 124 Clean
GtPl 313 SoulShuf 4 / 4 4 98 :
GtPl 314 Big Beat 4 / 4 4 115 Overdrive
GtPl 315 AcoJazz 4 / 4 4 204 ModernJazz
GtPl 316 ModernJz 4 / 4 16 218 :
GtPl 317 ShfBlues 4 / 4 4 115 Mute
GtPl 318 SlwBlues 4 / 4 2 49 Overdrive
GtPl 319 PnBoogie 4 / 4 4 160 Clean
GtPl 320 Reggae 4 / 4 2 102 :
Category Arp. No.
Arp.
Name
Time
Signature Length
Original
Tempo Voice TypeOwner’s Manual
AppendixGtPl 321 ReggeShf 4 / 4 4 90 :
GtPl 322 Samba 4 / 4 4 120 Nylon
GtPl 323 Bossa 4 / 4 4 124 :
GtPl 324 Spanish1 4 / 4 2 120 :
GtPl 325 Spanish2 4 / 4 2 120 Steel
GtPl 326 Lick1 4 / 4 4 120 Distortion
GtPl 327 Lick2 4 / 4 4 120 :
GtPl 328 Lick3 4 / 4 2 120 :
GtPl 329 Lick4 4 / 4 4 120 :
GtPl 330 Lick5 4 / 4 1 120 :
Strn 331 Strings 4 / 4 1 101 StereoSt1
Strn 332 New R&B 4 / 4 2 90 :
Strn 333 Pizz 4 / 4 1 120 Pizz
Bras 334 Funk1 4 / 4 4 132 Brass Sect
Bras 335 Funk2 4 / 4 1 132 :
Bras 336 Samba 4 / 4 2 120 :
RdPp 337 Hip Hop 4 / 4 2 105 TenorSax 2
RdPp 338 Soul 4 / 4 4 120 :
RdPp 339 Flutter 4 / 4 1 120 :
Lead 340 R&B Dsc1 4 / 4 1 110 Bass&Ld
Lead 341 R&B Dsc2 4 / 4 2 110 :
Lead 342 Regeton 4 / 4 4 98 Caliop Ld
Category Arp. No.
Arp.
Name
Time
Signature Length
Original
Tempo Voice TypeOwner’s Manual 47
Appendix
48MIDI Implimentation ChartOwner’s Manual
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más cercana o
el distribuidor autorizado que se lista debajo.CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
MEXICO
Yamaha de México S.A. de C.V.
Calz. Javier Rojo Gómez #1149,
Col. Guadalupe del Moral
C.P. 09300, México, D.F., México
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,
CEP 04534-013 Sao Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.
Sucursal de Argentina
Viamonte 1145 Piso2-B 1053,
Buenos Aires, Argentina
Tel: 1-4371-7021
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: +507-269-5311
THE UNITED KINGDOM
Yamaha-Kemble Music (U.K.) Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: 01908-366700
IRELAND
Danfay Ltd.
61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin
Tel: 01-2859177
GERMANY
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Central Europe GmbH,
Branch Switzerland
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 01-383 3990
AUSTRIA
Yamaha Music Central Europe GmbH,
Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/SLOVAKIA/
HUNGARY/SLOVENIA
Yamaha Music Central Europe GmbH,
Branch Austria, CEE Department
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-602039025
POLAND
Yamaha Music Central Europe GmbH
Sp.z. o.o. Oddzial w Polsce
ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland
Tel: 022-868-07-57
THE NETHERLANDS/
BELGIUM/LUXEMBOURG
Yamaha Music Central Europe GmbH,
Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040
FRANCE
Yamaha Musique France
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
ITALY
Yamaha Musica Italia S.P.A.
Combo Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha-Hazen Música, S.A.
Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: 91-639-8888
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
SWEDEN
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1
Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
DENMARK
YS Copenhagen Liaison Office
Generatorvej 6A
DK-2730 Herlev, Denmark
Tel: 44 92 49 00
FINLAND
F-Musiikki Oy
Kluuvikatu 6, P.O. Box 260,
SF-00101 Helsinki, Finland
Tel: 09 618511
NORWAY
Norsk filial av Yamaha Scandinavia AB
Grini Næringspark 1
N-1345 Østerås, Norway
Tel: 67 16 77 70
ICELAND
Skifan HF
Skeifan 17 P.O. Box 8120
IS-128 Reykjavik, Iceland
Tel: 525 5000
OTHER EUROPEAN COUNTRIES
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
TURKEY/CYPRUS
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jubel Ali,
Dubai, United Arab Emirates
Tel: +971-4-881-5868
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
25/F., United Plaza, 1468 Nanjing Road (West),
Jingan, Shanghai, China
Tel: 021-6247-2211
HONG KONG
Tom Lee Music Co., Ltd.
11/F., Silvercord Tower 1, 30 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel: 2737-7688
INDONESIA
PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 080-004-0022
MALAYSIA
Yamaha Music Malaysia, Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 3-78030900
PHILIPPINES
Yupangco Music Corporation
339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,
Makati, Metro Manila, Philippines
Tel: 819-7551
SINGAPORE
Yamaha Music Asia Pte., Ltd.
#03-11 A-Z Building
140 Paya Lebor Road, Singapore 409015
Tel: 747-4374
TAIWAN
Yamaha KHS Music Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd. Taipei.
Taiwan 104, R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
891/1 Siam Motors Building, 15-16 floor
Rama 1 road, Wangmai, Pathumwan
Bangkok 10330, Thailand
Tel: 02-215-2626
OTHER ASIAN COUNTRIES
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2317
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
NEW ZEALAND
Music Houses of N.Z. Ltd.
146/148 Captain Springs Road, Te Papapa,
Auckland, New Zealand
Tel: 9-634-0099
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
NORTH AMERICA
CENTRAL & SOUTH AMERICA
EUROPE
AFRICA
MIDDLE EAST
ASIA
OCEANIAHEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2445
SY41

PDF Document reader online

This website is focused on providing document in readable format, online without need to install any type of software on your computer. If you are using thin client, or are not allowed to install document reader of particular type, this application may come in hand for you. Simply upload your document, and Docureader.top will transform it into readable format in a few seconds. Why choose Docureader.top?

  1. Unlimited sharing - you can upload document of any size. If we are able to convert it into readable format, you have it here - saved for later or immediate reading
  2. Cross-platform - no compromised when reading your document. We support most of modern browers without the need of installing any of external plugins. If your device can oper a browser - then you can read any document on it
  3. Simple uploading - no need to register. Just enter your email, title of document and select the file, we do the rest. Once the document is ready for you, you will receive automatic email from us.

Previous 10

Next 10