Installation Guide - Air Lift Company

Copy and paste this link to your website, so they can see this document directly without any plugins.



Keywords

Lift, Performance, with, from, line, Company, will, warranty, suspension, this, vehicle, lower, spring, that, should, fig., pressure, (800), hose, product, loss, ride, have, Strut, other, which, MN-790, Front, service, leak

Transcript

For maximum effectiveness and safety,
please read these instructions completely
before proceeding with installation.
Failure to read these instructions can result in an
incorrect installation.
INSTALLATION GUIDE
M
N
-7
90

(0
21
31
1)

E
R
N
7
44
5
(2002 - 2007):
Kits 75551 & 75552
(2008 - 2012):
Kits 75554, 75556
Front Application for
Subaru Impreza, WRX & STi
2 MN-790
Air Lift Performance
1MN-790
Air Lift Performance
TABLE OF CONTENTS
A. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Notation Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Important Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
B. Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hardware List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
C. Installing the Air Suspension . . . . . . . . . . . . . . . . . . . . . . 4
Preparing the Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Stock Suspension Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installing the Kit Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Routing Air Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
D. Before Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting the Ride Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Suggested Driving Air Pressure and Maximum Air Pressure . . . . . . . . . . . . . . . . . . .7
Check for Binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Damping Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Aligning the Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Adjusting Extended or Drop Height Using Lower Mount . . . . . . . . . . . . . . . . . . . . . 10
Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Post-installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
E. Use, Maintenance and Servicing . . . . . . . . . . . . . . . . . . . 13
F. Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Tuning the Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Tips for Installing Air Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Checking for Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fixing Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Limited Warranty and Return Policy . . . . . . . . . . . . . . . . 15
How to Obtain Replacement Parts . . . . . . . . . . . . . . . . . 16
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2 MN-790
Air Lift Performance
DANGER
A. Introduction
CAUTION
WARNING
CAUTION
WARNING
NOTE
Air Lift Performance thanks you for purchasing the most complete, fully engineered highperformance air suspension made for the Suabru Impreza, WRX and STi. Read these
installation instructions to correctly and safely set up the vehicle for a #lifeonair.
Air Lift assumes that the installer has the mechanical knowledge and ability to work on
vehicle suspension systems and has basic tools necessary to complete the project.
Special tools needed to complete the installation are noted on the Installation Diagram
page.
Air Lift Performance reserves the right to make changes and improvements to its
products and publications at any time. For the latest version of this manual, contact Air
Lift Performance at (800) 248-0892 or visit www.airliftperformance.com.
An Air Lift air management system is highly recommended for this product. Learn more
at air-lift.co/productlines.
NOTATION EXPLANATION
Hazard notations appear in various locations in this publication. Information which is
highlighted by one of these notations must be observed to help minimize risk of personal
injury or possible improper installation which may render the vehicle unsafe. Notes are
used to help emphasize areas of procedural importance and provide helpful suggestions.
The following definitions explain the use of these notations as they appear throughout
this guide.
INDICATES IMMEDIATE HAZARDS WHICH WILL RESULT IN SEVERE PERSONAL
INJURY OR DEATH.
INDICATES HAZARDS OR UNSAFE PRACTICES WHICH COULD RESULT IN SEVERE
PERSONAL INJURY OR DEATH.
INDICATES HAZARDS OR UNSAFE PRACTICES WHICH COULD RESULT IN DAMAGE
TO THE MACHINE OR MINOR PERSONAL INJURY.
Indicates a procedure, practice or hint which is important to highlight.
IMPORTANT SAFETY NOTICES
DO NOT INFLATE AIR SPRINGS WHILE OFF OF THE VEHICLE. DAMAGE TO
ASSEMBLY MAY RESULT AND VOID WARRANTY.
DO NOT WELD TO, OR MODIFY PERFORMANCE STRUTS/SHOCKS IN ANY WAY.
DAMAGE TO UNIT MAY OCCUR AND WILL VOID WARRANTY.
3MN-790
Air Lift Performance
B. Installation Diagram
fig. B.1
C
D or E
F
A
B
Missing or damaged parts? Call Air Lift customer
service at (800) 248-0892 for a replacement part.STOP!
Kit Specific Hardware:
Kit #75551 (STi - GDF Chassis)
Item Part # Description ................................Qty
A 35211 Strut Assembly, Front Left .................. 1
B 35210 Strut Assembly, Front Right ............... 1
Kit #75552 (Impreza, WRX, STi - GDB Chassis)
Item Part # Description ................................Qty
A 35215 Strut Assembly, Front Left .................. 1
B 35214 Strut Assembly, Front Right ............... 1
Kit #75554 (STi - GRB Chassis)
Item Part # Description ................................Qty
A 35221 Strut Assembly, Front Left .................. 1
B 35222 Strut Assembly, Front Right ............... 1
Kit #75556 (Impreza, WRX - GH, GR, GV, GE Chassis)
Item Part # Description ............................... Qty
A 35229 Strut Assembly, Front Left ..................1
B 35228 Strut Assembly, Front Right ...............1
Common Hardware:
Item Part # Description ............................... Qty
C 20997 Leader Hose, 1/4” ID ..........................2
D 21810 1/4”FNPT x 1/4” Fitting “DOT” ............2
E 21987 1/4”FNPT x 3/8” Fitting “DOT” ............2
F Spanner Wrench ................................1
HARDWARE LIST
4 MN-790
Air Lift Performance
PREPARING THE VEHICLE
1. Elevate and support the vehicle with a hoist or jack stands.
2. Remove the front wheel and support the hub assembly.
STOCK SUSPENSION REMOVAL
1. Remove the bolts retaining the brake hose and the ABS sensor wire (Figs. C.1 and C.2).
2. Disconnect the stabilizer bar from the transverse link (Fig. C.3).
3. Support the hub then unbolt and remove the two lower strut mount bolts (Fig. C.4).
C. Installing the Air Suspension
fig. C.1
fig. C.2
fig. C.4
fig. C.3
5MN-790
Air Lift Performance
4. Unthread the three upper bracket nuts within the engine compartment and remove the
strut from the vehicle (Fig. C.5).
INSTALLING THE KIT COMPONENTS
1. Begin by installing the leader line into the air spring (Fig. C.6). Wrap the threads of the
leader hose with Teflon tape or thread sealant. Tighten the appropriate fitting to the
airline 1 and 3/4 turns beyond hand tight. Tighten the leader line into the air spring 1
and 3/4 turns beyond hand tight.
2. To gain full use of the camber plates, some inner fender modifications should be done
to insure clearance around the new air spring assembly (Fig. C.7). All bolts should be
trimmed flush with the mounting nuts. All unused nuts should be removed. Some vehicles
may require some modification to form the sheet metal away from the air spring (2005
STi left inner fender shown: RED=trim, GREEN=remove, BLUE=form).
fig. C.5
fig. C.6
fig. C.7
1. Fully compress the suspension using a jack. With the suspension compressed,
review the best routing for the leader hose that is clear of all suspension and
steering components.
2. Routing should also allow for the suspension to extend and steer without
kinking, pulling the line tight or rubbing on other components. Following the
brake line routing is often a good place to start. Check clearances to all other
components.
6 MN-790
Air Lift Performance
ROUTING THE AIR LINES
3. Align the strut assembly with the upper bracket holes in the strut tower. Thread the nuts
onto the camber plate studs. Lift the hub assembly into the strut lower mount and reinstall
the bolts. See Torque Specifications chart (Table 1).
4. Reinstall the brake hose bracket and ABS sensor wire bracket. See Torque Specifications
chart (Table 1).
5. Reinstall the stabilizer bar into the lower transverse link. See Torque Specifications chart.
6. Route the braided air line in a manner where the line will not be kinked or rubbed by
anything. Cycle the suspension up and down; turn the wheel lock-to-lock to verify the air
line is protected from damage. Generally, routing the air lines along with the brake line
is a good place to start.
7MN-790
Air Lift Performance
SETTING THE RIDE HEIGHT
1. With the suspension fully compressed, take a measurement from the fender to a
chosen reference point – typically the center of the axle. Record this measurement as
max compression (MC).
2. Cycle the suspension to max extension (ME) and record the measurement from the
fender to the same reference point.
3. Add ME and MC, then divide the total by 2. Set the suspension to this point. This
position will give 50% stroke in either direction and is a starting point for ride height.
(Fig. D.1)
4. With the suspension at this position, loosen, then re-torque the lower control arm
bolts to manufacturer’s specifications (Table 1):
Formula for Calculating Ride Height
(ME+MC)÷2=MID STROKE
Table 1
FAILURE TO MAINTAIN ADEQUATE MINIMUM PRESSURE (OR PRESSURE
PROPORTIONAL TO LOAD) MAY RESULT IN EXCESSIVE BOTTOMING OUT AND WILL
VOID THE WARRANTY.
125 PSI
Maximum Air PressureSuggested Driving Air Pressure
Torque Specifications
Location Nm Lb.-ft.
Camber plate to chassis 20 15
Camber plate adjustment bolts 15 11
Strut lower mount bolts (2002 - 2007) 175 129
Strut lower mount bolts (2008 and up) 155 114
ABS speed sensor bolt 33 24
Brake hose bolt 32 24
Transverse link rear bushing 190 140
Transverse link to cross-member 125 92
Stabilizer bar to transverse link(STi) 45 33
Stabilizer bar to transverse link(Impreza/WRX) 30 22
Wheel bolts 90 66
D. Before Operating
fig. D.1
50 PSI
8 MN-790
Air Lift Performance
MAKE SURE THE FRONT WHEELS ARE STRAIGHT WHEN DEFLATING AND
REINFLATING AIR BAGS.
CHECK FOR BINDING
1. Inflate and deflate the system (do not exceed 125 PSI) to check for clearance or
binding issues. With the air springs deflated, check clearances on everything so as
not to pinch brake lines, vent tubes, etc. Clear lines if necessary.
2. Inflate the air springs to 75-90 PSI and check all connections for leaks.
3. Please continue by reading the Product Use, Maintenance and Servicing section.
CAUTION
9MN-790
Air Lift Performance
ALIGNING THE VEHICLE
1. Set the vehicle to the height at which it will most often be driven.
2. If the ride height is lower than stock, Air Lift recommends loosening all pivot points
(bolts, nuts) on any control arm, strut arm or radius rod that contains bushings. Once
they have been loosened, re-torque to stock specifications (Table 1).
It may be necessary to cycle the suspension to loosen the bushing from its mount. This will
help re-orient the bushing at its new position based on the chosen ride height.
3. Get a shop alignment of the vehicle at the new chosen ride height.
fig. D.3fig. D.2
DAMPING ADJUSTMENT
Suspension damping is a matter compromise. Setting it too stiff will make the ride feel
jarring. In addition, if the suspension is too stiff, the tires will lose contact with the road,
reducing control and power delivery. Conversely, if the suspension is too soft, the car
can experience brake dive and excessive bouncing. The sweet spot lies somewhere in
the middle. Air Lift dampers have a range of adjustment, which allows the driver to tune
the ride and handling to his or her preferences.
Air Lift recommends damper and air pressure settings for every vehicle kit, but it is
impossible to consider every situation. For example, even though Air Lift kits replace
the dampers and springs, vehicles with sport-tuned suspensions might have stiffer
bushings, larger anti-roll bars, bigger wheels, wider tires, etc. So these settings may
need to be adjusted to different vehicles and driving characteristics.
1. The dampers in this kit have 30 settings, or “clicks,” of adjustable compression and
rebound damping characteristics. Damping is changed through the damper rod using
the supplied adjuster (Figs. D.2 & D.3) or an M3 hex key (not included).
2. Turn the adjuster clockwise (H) and the damping settings are stiffened, reducing
oscillations and body motion. Turn the adjuster counterclockwise (S) and the
damping is softened.
3. Each damper in this kit is preset to “-15 clicks.” This means that the damper is
adjusted 15 clicks away from full stiff, which starts at 0. Counting up from full stiff
is the preferred method of keeping track of, or setting, damping. This setting was
developed on a 2005 Subaru STi.
NOTE
10 MN-790
Air Lift Performance
ADJUSTING EXTENDED OR DROP HEIGHT
USING LOWER MOUNT
These dampers have been pre-set at the factory to provide maximum drop height while
maintaining adequate tire clearance to the air spring. If you wish to gain more extended
height (lift), which is the same as reducing drop height, or want to lower the chassis
further and there is still adjustment available at the lower mount, please use the following
procedure:
1. Support the vehicle with jack stands or a hoist at approved lifting points.
2. Remove the wheel.
3. Using the supplied spanner wrench, loosen the locking collar. (Fig. D.4)
4. Deflate the air spring to 0 PSI on the corner you are adjusting.
5. Disconnect lower mount from suspension.
6. Spin the lower mount to the desired location.
Not all models will have further drop height available.
7. Re-install lower mount to suspension and torque fasteners.
8. Tighten the lower locking collar to the lower mount using significant force.
NOTE
The dampers in this
kit may look different,
but they all allow
adjustment of the
locking collar with
the included spanner
wrench.
fig. D.4
11MN-790
Air Lift Performance
FOR STRUTS: FOR SHOCKS:
Thread
MUST be
showing in
window.
WHEN ADJUSTING HEIGHT UPWARD, MAKE SURE THAT THE DAMPER BODY
ENGAGES ALL THE THREADS OF THE LOWER MOUNT (FIG. D.5). WHEN ADJUSTING
DOWNWARD, MAKE SURE THERE IS ADEQUATE AIR SPRING CLEARANCE TO THE
TIRE/WHEEL ASSEMBLY. CLEARANCE MUST BE CHECKED WITH SYSTEM FULLY
DEFLATED AS WELL AS FULLY INFLATED TO ENSURE THAT NO RUBBING OCCURS.
FAILURE TO MAINTAIN ADEQUATE CLEARANCE CAN RESULT IN AIR SPRING
FAILURE AND WILL NOT BE COVERED UNDER WARRANTY.
DO NOT ADJUST HEIGHT BY SPINNING AIR SPRING ON DAMPER! DOING SO MAY
CAUSE AN AIR LEAK AND COMPROMISE THE ASSEMBLY.
OK, no threads
showing.
Not OK, threads
are showing.
CAUTION
CAUTION
fig. D.5
12 MN-790
Air Lift Performance
 Clearance — Inflate the air springs to 75-90 PSI and make sure there is at least 1/2”
clearance from anything that might rub against the air spring. This should be checked
with the air spring fully inflated and fully deflated.
 Leak — Inflate the air springs to 75-90 PSI and check all connections for leaks. All
leaks must be eliminated before the vehicle is road tested.
 Heat — Be sure there is sufficient clearance from heat sources, at least 6” for air
springs and air lines. If a heat shield was included in the kit, install it. If there is no
heat shield, but one is required, call Air Lift customer service at (800) 248-0892.
 Fastener — Recheck all bolts for proper torque.
 Road — Inflate the springs to recommended driving pressures. Drive the vehicle 10
miles and recheck for clearance, loose fasteners and air leaks.
 Operating instructions — If professionally installed, the installer should review
the operating instructions with the owner. Be sure to provide the owner with all
paperwork that came with the kit.
INSTALLATION CHECKLIST
 Overnight leak down test — Recheck air pressure 24 hours after installation and
driving of the vehicle. If the pressure has dropped more than 5 PSI, there is a leak
that must be fixed.
 Air pressure requirements — It is important to understand the air pressure
requirements of the air spring system. Regardless of load, the air pressure should
always be adjusted to maintain adequate ride height at all times while driving.
 Thirty-day or 500-mile test —Recheck the air spring system after 30 days or 500
miles, whichever comes first. If any part shows signs of rubbing or abrasion, the
source should be identified and moved, if possible. If it is not possible to relocate
the cause of the abrasion, the air spring may need to be remounted. If professionally
installed, the installer should be consulted. Check all fasteners for tightness.
POST-INSTALLATION CHECKLIST
13MN-790
Air Lift Performance
PROBLEM CAUSE SOLUTION
System won’t maintain pressure
overnight.
Improperly installed air line, air line has
holes or cracks or leak in the tank.
Leak test the air line connections, the
threaded connection into the air spring, and all
fittings in the control system.
Compressor runs all the time. The compressor relay is defective or
there is a leak in the air lines.
Replace the relay or find the air leak.
Air spring or tank leak. Fitting seal or air line is compromised. Check to make sure air lines are seated in
connectors. Inspect fittings with soapy water.
Trim hose or re-seal fitting. Ensure lines are
cut straight.
Corner won't raise or air leak
develops.
Look for a kink or fold in the air line. Replace any air line that has been kinked.
F. Troubleshooting Guide
1. An Air Lift air management system is strongly recommended for this product, but it
is possible to operate without one. The air lines can be routed to Schrader valves for
use with a separate air compressor. Air lines and Schrader valves are not included
with Air Lift Performance kits and would need to be purchased separately. To learn
more Air Lift management systems visit air-lift.co/productlines.
2. Check the air pressure before driving.
SHOULD IT BECOME NECESSARY TO RAISE THE VEHICLE BY THE FRAME, MAKE
SURE THE CONTROL SYSTEM IS TURNED OFF BEFORE LIFTING.
TUNING THE AIR PRESSURE
Pressure determination comes down to three things — level vehicle, ride comfort
and stability.
1. Level vehicle
Depending on load, it is possible one side will need more pressure than the other to
level the vehicle.
2. Ride comfort
If the vehicle has a harsh ride, it may be due to either too much pressure or not
enough causing frequent bottoming. Also, riding the vehicle at the top, or close to
the top of the available stroke will cause a very uncomfortable ride due to a lack of
rebound travel. This situation should be avoided for driving any significant distance.
Try different pressures to determine the best ride comfort. See Air Lift suggested
driving air pressure for this vehicle.
3. Stability
Stability translates into safety and should be the priority, meaning the driver may
need to sacrifice a perfectly level and comfortable ride. Stability issues include roll
control, bounce, dive during braking and sponginess. Tuning out these problems
usually requires additional air pressure, damping or both.
E. Use, Maintenance and Servicing
CAUTION
14 MN-790
Air Lift Performance
CHECKING FOR LEAKS
1. Inflate the air spring to at least 80 PSI.
2. Spray all connections with a solution of 1/5 liquid dish soap and 4/5 water. Spot leaks
easily by looking for bubbles in the soapy water.
4. Check the air pressure again after 24 hours. A 2-4 PSI loss after initial installation is
normal. Retest for leaks if the loss is more than 5 PSI.
FIXING LEAKS
1. Air line to PTC fitting: Try pushing the air line firmly into the fitting to ensure it is
properly seated. If leak persists, deflate the spring and remove the air line by pushing
the collar toward the fitting body and pulling firmly on the air line. Trim 1” off the end
of the air line making sure the cut is clean and square. Reinsert air line firmly into
fitting and pull back on the air line to make sure it is seated.
2. Threaded connection: If possible, tighten the fitting another half turn. If the leak
persists, deflate spring, remove fitting and re-coat threads with thread sealant.
Reinstall to hand tight and then use wrench to finish tightening an additional 1 3/4
turns.
3. Air spring o-ring seal: If a leak is found at the upper or lower air spring seal on a
strut or shock, contact Air Lift customer service at (800) 248-0892.
TIPS FOR INSTALLING AIR LINES
When cutting air lines, use a sharp knife or a hose
cutter and make clean, square cuts (Fig. F.1). Do not
use scissors or wire cutters because these tools will
deform the air line, causing it to leak around fittings.
Do not cut the lines at an angle.
Do not bend the 1/4” hose at a radius of less than 1”
and do not put side load pressure on fitting. The hose
should be straight beyond the fitting for 1” before
bending.
Inspect hose for scratches that run lengthwise on hose
prior to installation. Contact Air Lift customer service
at (800) 248-0892 if the air line is damaged.
To watch a video demonstrating proper air
line cutting, go to air-lift.co/cuttingairline
fig. F.1
15MN-790
Air Lift Performance
Notes
16 MN-790
Air Lift Performance
Limited Warranty and Return Policy
WHAT THIS WARRANTY COVERS
Air Lift Company, for all Air Lift Performance products, except its Air Lift Performance 3H™ and 3P™ systems, warrants to the original
purchaser for a period of one year from the date of original purchase that the Air Lift Performance damper kits will be free from defects in
workmanship and materials for the normal expected life of the part when used on cars and trucks as specified by Air Lift Company and
under normal operating conditions, subject to the requirements and exclusions set forth below.
Air Lift Company provides a Limited Lifetime Warranty to the original purchaser of its Air Lift Performance 3H™ and 3P™ Control/Air
Management Systems, that the Air Lift Performance products will be free from defects in workmanship and materials for the normal
expected life of the part when used on cars and trucks as specified by Air Lift Company and under normal operating conditions, subject
to the requirements and exclusions set forth below.
WHAT THIS WARRANTY DOES NOT COVER
The warranty does not apply to products that have been improperly applied, improperly installed, or which have not been maintained
in accordance with installation instructions furnished with all products. This warranty does not apply and is void if damage or failure is
caused by: accident, abuse, misuse (including but not limited to racing or off-road activities or commercial use), abnormal use, faulty
installation, liquid contact, fire, earthquake or other external cause; operating the product outside Air Lift Company’s instructions, specifications or guidelines; or service, alteration, maintenance or repairs performed by anyone other than Air Lift Company to the product from
its purchased condition. This warranty also does not apply to: Universal Air (Fabricator Kits), consumable parts, such as batteries; cosmetic damage, including but not limited to scratches or dents; defects caused by normal wear and tear or otherwise due to the normal
aging of the product, or if any serial or identification number has been removed or defaced from the product. Air Lift Company reserves
the right to change the design of any product without assuming any obligation to modify any product previously manufactured.
LIMITATION OF LIABILITY
To the extent permitted by law, this warranty and the remedies set forth herein are exclusive and in lieu of all other warranties, remedies
and conditions, whether oral, written, statutory, express or implied. AIR LIFT COMPANY DISCLAIMS ALL STATUTORY AND IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE AND WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS TO THE EXTENT PERMITTED BY LAW. To the extent such warranties cannot be disclaimed, such implied warranties shall apply only for the warranty period specified above. Please note that some states
do not allow limitation on how long an implied warranty (or condition) lasts. So the above limitation may not apply to you.
Except as provided in this warranty and to the extent permitted by law, Air Lift Company shall not be liable for any direct, special, incidental or consequential damages resulting from any breach of warranty or condition, or arising in connection with the sale, use or repair
of air lift products, or under any other legal theory, including but not limited to loss of use, loss of revenue, loss of actual or anticipated
profits, loss of the use of money, loss of business, loss of opportunity, loss of goodwill, and loss of reputation. Air Lift Company’s maximum liability shall not in any case exceed the purchase price paid by you for the Air Lift product. Please note that some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
HOW TO GET SERVICE
If a defect in workmanship or materials causes your Air Lift Performance product to become inoperable within the warranty period,
before returning any defective product, call Air Lift Company at (800) 248-0892 in the U.S. and Canada (elsewhere, (517) 322-2144) to
obtain a Returned Materials Authorization (RMA) number. The consumer shall be responsible for removing (labor charges) the defective
product from the vehicle and returning it, shipping costs prepaid, to Air Lift Company for verification. Returns to Air Lift Company must
be postage prepaid and sent to: Air Lift Company • 2727 Snow Road • Lansing, MI • 48917. You must prove to the satisfaction of Air
Lift Company the date of original purchase of your Air Lift Performance product. You must also enclose the RMA number and a return
address. A minimum $10 shipping and handling charge will apply to all warranty claims. You must also pack the product to minimize
the risk of it being damaged in transit. If we receive a product in damaged condition as the result of shipping, we will notify you and you
must seek a claim with the shipper.
WHAT AIR LIFT COMPANY WILL DO
If you submit a valid claim to Air Lift Company during the warranty period, Air Lift Company will, at its option, repair your Air Lift Performance product or furnish you with a new or rebuilt product. Air Lift Company will not reimburse you for repairs or replacement parts
provided by other parties. Your repaired or replacement Air Lift Performance product will be returned to you (subject to payment of the
required warranty claim shipping and handling charge) and it will be covered under the warranty for the balance of the warranty period,
if any. When a product or part is replaced, any replacement item becomes your property and the replaced item becomes property of Air
Lift Company. You are responsible for installation/reinstallation (labor charges) of the product.
HOW THE LAW RELATES TO THIS WARRANTY
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. By this warranty, Air Lift
Company does not limit or exclude your rights except as allowed by law. To fully understand your rights, you should consult the laws of
your state.
17MN-790
Air Lift Performance
How to Obtain Replacement Parts
If you need replacement parts, contact the local dealer or call Air Lift customer service at
(800) 248-0892. Most parts are immediately available and can be shipped the same day.
Contact Air Lift Company customer service at (800) 248-0892 first if:
 Parts are missing from the kit.
 Need technical assistance on installation or operation.
 Broken or defective parts in the kit.
 Wrong parts in the kit.
 Have a warranty claim or question.
Contact the retailer where the kit was purchased:
 If it is necessary to return or exchange the kit for any reason.
 If there is a problem with shipping if shipped from the retailer.
 If there is a problem with the price.
Contact Information
If you have any questions, comments or need technical assistance contact Air Lift
Company’s customer service department by calling (800) 248-0892, Monday through
Friday. For calls from outside the USA or Canada, dial (517) 322-2144. Contact customer
service anytime by email at techsupport@airliftperformance.com.
For inquiries by mail, Air Lift Company’s address is P.O. Box 80167, Lansing, MI 489080167. The shipping address for returns is 2727 Snow Road, Lansing, MI 48917.
Contact the Air Lift sales team anytime at sales@airliftcompany.com or visit
www.airliftperformance.com.
Need Help?
Contact Air Lift Company customer service
department by calling (800) 248-0892. For calls from
outside the USA or Canada, dial (517) 322-2144.
Air Lift Performance • 2727 Snow Road • Lansing, MI 48917 or P.O. Box 80167 • Lansing, MI 48908-0167
Toll Free (800) 248-0892 • Local (517) 322-2144 • Fax (517) 322-0240 • www.airliftperformance.com
Printed in
the USA
Thank you for purchasing Air Lift Performance products!
Connect by searching for Air Lift Performance #LifeonAir

PDF Document reader online

This website is focused on providing document in readable format, online without need to install any type of software on your computer. If you are using thin client, or are not allowed to install document reader of particular type, this application may come in hand for you. Simply upload your document, and Docureader.top will transform it into readable format in a few seconds. Why choose Docureader.top?

  1. Unlimited sharing - you can upload document of any size. If we are able to convert it into readable format, you have it here - saved for later or immediate reading
  2. Cross-platform - no compromised when reading your document. We support most of modern browers without the need of installing any of external plugins. If your device can oper a browser - then you can read any document on it
  3. Simple uploading - no need to register. Just enter your email, title of document and select the file, we do the rest. Once the document is ready for you, you will receive automatic email from us.

Previous 10

Next 10