Hyster S40-70FT Lift Truck Dimensions

Copy and paste this link to your website, so they can see this document directly without any plugins.



Keywords

(mm), with, mast, Hyster, ft/min, (m/s), Cushion, rear, (kg), front, Opt., (LP), 102.0, (Gas), type, 88.0, Company, standard, Controlled, Hydraulic, 19.9, Drawbar, pull,, lbf,, (kN), Gradeability,, (610), .45), Lift, system

Transcript

5o FWD
8o BACK
25.4
(645) 13.8
(350)
33.3o
11.8
(300)
56.3
(1 430)
15
11
12
17
10
18
22
36.7
(929)
19
36.0
(914)
42.0
(1 068)
S40-70FT 46.4 (1 178)
S55FTS 48.5 (1 231)
Non-suspension
Semi-suspension
Full-suspension
Std. OHG
42.0 (1 067)
42.5 (1 079)
42.0 (1 067)
Opt. OHG
39.3 (1 000)
39.8 (1 012)
N/A
P
4.4
(112)
36
37
16
S40-50FT, 55FTS
S60-70FT
14.9 (378)
15.2 (385)
Std. 84 (2 128)
Opt. 82 (2 061)
R
MODEL P R
in. (mm) Percent
S40FT 16.5 (418) 50%
S50FT 18.6 (472) 45%
S55FTS 15.9 (405) 47%
S60FT 21.3 (541) 39%
S70FT 23.3 (591) 39%
Hyster S40-70FT Lift Truck Dimensions
Circled dimensions correspond to the line numbers on the tabulated chart inside the Technical Guide. Dimensions are in inches (millimeters).
Truck shown with optional equipment - Lights Package and TouchPointTM hydraulics with fully adjustable armrest.
TRUCK LOAD
MODEL CAPACITY CENTER
lb. (kg) in. (mm)
S40FT 4,000 (1 814) 24 (610)
S50FT 5,000 (2 268) 24 (610)
S55FTS 5,500 (2 495) 24 (610)
S60FT 6,000 (2 721) 24 (610)
S70FT 7,000 (3 175) 24 (610)
2
Hyster S40FT Lift Truck Specifications
* CERTIFICATION: These Hyster lift trucks meet design specifications of Part II ANSI B56.1-1969, as required by OSHA Section 1910.178(a)(2) and also comply with Part III ANSI B56.1-revision in effect at time
of manufacture. Certification of compliance with the applicable ANSI standards appears on the lift truck.
† NOTE: Performance specifications/ratings are for truck equipped as described under Standard Equipment in this Technical Guide. Performance specifications are affected by the condition of the vehicle and how it
is equipped, as well as by the nature and condition of the operating area. Specifications are subject to change and you should discuss the proposed application with your authorized Hyster Dealer.
†† Limited by traction. For further information on this dimension, please contact your local Hyster Company dealer.
¥ Specifications given are for both LP and Gas where applicable unless otherwise noted.
PE
R
FO
R
M
AN
C
E

W
T.
TI
R
ES
&
W
H
EE
LS
PO
W
ER
TR
AI
N
D
IM
EN
SI
O
N
S
G
EN
ER
AL
1 Manufacturer Hyster Company Hyster Company Hyster Company
2 FortisTM Series, Model S40FT (Fortis) S40FT (Fortis Advance) S40FT (Fortis Advance+)
Transmission Type Basic Electronic DuraMatchTM DuraMatch, DuraMatch Plus DuraMatch Plus2
3 Capacity, rated lb. (kg) 4,000 (1 814) 4,000 (1 814) 4,000 (1 814)
4 Load center in. (mm) 24 (610) 24 (610) 24 (610)
5 Engine / Power type Mazda 2.0L / LP, Gas Mazda 2.2L / LP, Gas GM 2.4 L / LP, Gas
6 Operator type Sit Sit Sit
7 Tire type, front / rear Cushion / Cushion Cushion / Cushion Cushion / Cushion
8 Wheels, front / rear (X=drive) 2X / 2 2X / 2 2X / 2
10 2-stg. LFL (TOF) in. (mm) 129 (3 292) 129 (3 292) 129 (3 292)
11 Limited free-lift (TOF) in. (mm) 5 (140) 5 (140) 5 (140)
12 Optional full free-lift (TOF) with / without LBE in. (mm) 36 / 62 (910 / 1 575) 36 / 62 (910 / 1 575) 36 / 62 (910 / 1 575)
13 Forks, thickness / width / length in. (mm) 1.6x3.9x42.0 (40x100x1 067) 1.6x3.9x42.0 (40x100x1 067) 1.6x3.9x42.0 (40x100x1 067)
14 Tilt angle, forward / backward Deg. ° 5 / 8 5 / 8 5 / 8
15 Length to face of forks in. (mm) 87.6 (2 226) 87.6 (2 226) 87.6 (2 226)
16 Width, standard tires / wide tread in. (mm) 42.1 / 48.9 (1 070 / 1 242) 42.1 / 48.9 (1 070 / 1 242) 42.1 / 48.9 (1 070 / 1 242)
17 Height, standard mast lowered in. (mm) 85 (2 135) 85 (2 135) 85 (2 135)
18 Height, std. mast extended with / without LBE in. (mm) 178 / 151 (4 515 / 3 840) 178 / 151 (4 515 / 3 840) 178 / 151 (4 515 / 3 840)
19 Turning radius, minimum outside in. (mm) 76.7 (1 950) 76.7 (1 950) 76.7 (1 950)
20 Center of wheel to face of forks in. (mm) 14.9 (378) 14.9 (378) 14.9 (378)
21 Right Angle Stack (Add load length for 90° stack) in. (mm) 91.6 (2 328) 91.6 (2 328) 91.6 (2 328)
22 Equal Intersecting Aisle (W=42 in., L=48 in.) in. (mm) 74.0 (1 880) 74.0 (1 880) 74.0 (1 880)
23 Stability (Comply with ANSI?) * YES YES YES
24 Travel speed RL / NL mph (km/h) 10.6 / 10.3 (17.0 / 16.6) 10.6 / 10.3 (17.0 / 16.6) 10.7 / 10.5 (17.2 / 16.9) 11.3 / 11.2 (18.3 / 18.0)
25 Lift speed, standard mast RL / NL ¥ ft/min (m/s) 106.0 / 110.0 (.54 / .56) 110.0 / 110.0 (.56 / .56) 119.0 / 119.0 (.60 / .60)
Opt. 2-stage FFL mast RL / NL ¥ ft/min (m/s) 95.0 / 99.0 (.48 / .50) 99.0 / 99.0 (.50 / .50) 106.0 / 106.0 (.54 / .54)
Opt. 3-stage FFL mast RL / NL ¥ ft/min (m/s) 101.0 / 105.0 (.51 / .53) 105.0 / 105.0 (.53 / .53) 113.0 / 113.0 (.57 / .57)
26 Lowering, standard mast RL / NL ¥ ft/min (m/s) 100.0 / 88.0 (.51 / .45) 100.0 / 88.0 (.51 / .45) 99.0 / 86.0 (.50 / .44)
Opt. 2-stage FFL mast RL / NL ¥ ft/min (m/s) 85.0 / 62.0 (.43 / .31) 85.0 / 62.0 (.43 / .31) 86.0 / 60.0 (.44 / .30)
Opt. 3-stage FFL mast RL / NL ¥ ft/min (m/s) 94.0 / 75.0 (.48 / .38) 94.0 / 75.0 (.48 / .38) 97.0 / 81.0 (.49 / .41)
27 Drawbar pull, 1 mph RL / NL (LP) lbf, (kN) 3,300 / 2,155 (14.7 / 9.6) 3,989 / 2,155 (17.8 / 9.6) 4,627 / 2,155 (20.6 / 9.6) 4,900 / 2,155 (21.8 / 9.6)
Drawbar pull, 1 mph RL / NL (Gas) lbf, (kN) 3,853 / 2,155 (17.1 / 9.6) 4,198 / 2,155 (18.7 / 9.6) 4,130 / 2,155 (18.4 / 9.6)
Drawbar pull, 3 mph RL / NL (LP) lbf, (kN) 2,000 / 2,000 (8.9 / 8.9) 1,600 / 2,155 (7.1 / 9.6) 3,100 / 2,155 (13.8 / 9.6) 3,500 / 2,155 (15.6 / 9.6)
Drawbar pull, 3 mph RL / NL (Gas) lbf, (kN) 2,500 / 2,155 (11.1 / 9.6) 2,750 / 2,155 (12.2 / 9.6) 2,800 / 2,155 (12.5 / 9.6) 3,200 / 2,155 (14.2 / 9.6)
28 Gradeability, 1 mph RL / NL (LP) % 28.4 / 28.4 35.0 / 29.3 41.5 / 29.3 44.3 / 29.3
Gradeability, 1 mph RL / NL (Gas) % 33.7 / 29.3 37.1 / 29.3 36.4 / 29.3
Gradeability, 3 mph RL / NL (LP) % 17.5 / 17.5 23.0 / 23.0 28.0 / 28.0 32.0 / 29.3
Gradeability, 3 mph RL / NL (Gas) % 22.0 / 22.0 25.0 / 25.0 24.0 / 24.0 26.9 / 26.9
30 Weight, total approximate, std. truck config. NL lb. (kg) 7,837 (3 555) 7,837 (3 555) 7,837 (3 555)
31 Axle loading, static, front / rear NL lb. (kg) 3,567 / 4,270 (1 618 / 1 937) 3,567 / 4,270 (1 618 / 1 937) 3,567 / 4,270 (1 618 / 1 937)
Axle loading, static, front / rear RL lb. (kg) 10,321 / 1,516 (4 682 / 688) 10,321 / 1,516 (4 682 / 688) 10,321 / 1,516 (4 682 / 688)
33 Size of tires, drive (front) / steer (rear) 21x7x15 / 16x5x10.5 21x7x15 / 16x5x10.5 21x7x15 / 16x5x10.5
34 Wheelbase in. (mm) 56.3 (1 430) 56.3 (1 430) 56.3 (1 430)
35 Tread, center of tires front / rear in. (mm) 35.1 (892) 35.1 (892) 35.1 (892)
36 Ground clearance, lowest point NL in. (mm) 3.6 (91) 3.6 (91) 3.6 (91)
37 Ground clearance, center wheelbase NL in. (mm) 4.9 (125) 4.9 (125) 4.9 (125)
38 Brakes, method of control, service / parking Foot / Hydraulic Foot / Hydraulic Foot / Hydraulic
39 Brakes, method of operation, service / parking Hand / Mechanical Hand / Mechanical Hand / Mechanical
40 Battery, volts / cold cranking amps V (amps) 12 / 475 12 / 475 12 / 475
42 Permanent output @ 2600 rpm LP / Gas hp (ps) 44 / 50 51 / 54 62 / 63
43 Torque at 1800 rpm LP / Gas lbf,/f (kg/m) 82.0 / 93.0 94.0 / 101.0 123.0 / 103.0
44 No. cylinders / displacement (cu.in.) / liters 4 / 122 / 2.0L 4 / 134 / 2.2L 4 / 146.5 / 2.4L
46 Gear change type Powershift Powershift Powershift
47 Number of speeds, forward / reverse 1 / 1 1 / 1 1 / 1 2 / 1
48 Transmission type Electronically Controlled Electronically Controlled Electronically Controlled
55 Relief pressure for attachments psi (kPA) 2,250 (15.5) 2,250 (15.5) 2,250 (15.5)
3
4
Hyster S50FT Lift Truck Specifications
PE
R
FO
R
M
AN
C
E

W
T.
TI
R
ES
&
W
H
EE
LS
PO
W
ER
TR
AI
N
D
IM
EN
SI
O
N
S
G
EN
ER
AL
1 Manufacturer Hyster Company Hyster Company Hyster Company
2 FortisTM Series, Model S50FT (Fortis) S50FT (Fortis Advance) S50FT (Fortis Advance+)
Transmission Type Basic Electronic DuraMatchTM DuraMatch, DuraMatch Plus DuraMatch Plus2
3 Capacity, rated lb. (kg) 5,000 (2 268) 5,000 (2 268) 5,000 (2 268)
4 Load center in. (mm) 24 (610) 24 (610) 24 (610)
5 Engine / Power type Mazda 2.0L / LP, Gas Mazda 2.2L / LP, Gas GM 2.4L / LP, Gas
6 Operator type Sit Sit Sit
7 Tire type, front / rear Cushion / Cushion Cushion / Cushion Cushion / Cushion
8 Wheels, front / rear (X=drive) 2X / 2 2X / 2 2X / 2
10 2-stg. LFL (TOF) in. (mm) 129 (3 292) 129 (3 292) 129 (3 292)
11 Limited free-lift (TOF) in. (mm) 5 (140) 5 (140) 5 (140)
12 Optional full free-lift (TOF) with / without LBE in. (mm) 36 / 62 (910 / 1 575) 36 / 62 (910 / 1 575) 36 / 62 (910 / 1 575)
13 Forks, thickness / width / length in. (mm) 1.6x3.9x42.0 (40x100x1 067) 1.6x3.9x42.0 (40x100x1 067) 1.6x3.9x42.0 (40x100x1 067)
14 Tilt angle, forward / backward Deg. ° 5 / 8 5 / 8 5 / 8
15 Length to face of forks in. (mm) 89.8 (2 280) 89.8 (2 280) 89.8 (2 280)
16 Width, standard tires / wide tread in. (mm) 42.1 / 48.9 (1 070 / 1 242) 42.1 / 48.9 (1 070 / 1 242) 42.1 / 48.9 (1 070 / 1 242)
17 Height, standard mast lowered in. (mm) 85 (2 135) 85 (2 135) 85 (2 135)
18 Height, std. mast extended with / without LBE in. (mm) 178 / 151 (4 515 / 3 840) 178 / 151 (4 515 / 3 840) 178 / 151 (4 515 / 3 840)
19 Turning radius, minimum outside in. (mm) 78.7 (2 000) 78.7 (2 000) 78.7 (2 000)
20 Center of wheel to face of forks in. (mm) 14.9 (378) 14.9 (378) 14.9 (378)
21 Right Angle Stack (Add load length for 90° stack) in. (mm) 93.6 (2 378) 93.6 (2 378) 93.6 (2 378)
22 Equal Intersecting Aisle (W=42 in., L=48 in.) in. (mm) 74.9 (1 902) 74.9 (1 902) 74.9 (1 902)
23 Stability (Comply with ANSI?) * YES YES YES
24 Travel speed RL / NL mph (km/h) 10.6 / 10.3 (17.0 / 16.6) 10.6 / 10.3 (17.0 / 16.6) 10.7 / 10.5 (17.2 / 16.9) 11.3 / 11.2 (18.3 / 18.0)
25 Lift speed, standard mast RL / NL ¥ ft/min (m/s) 92.0 / 110 (.47 / .56) 110.0 / 110.0 (.56 / .56) 119.0 / 119.0 (.60 / .60)
Opt. 2-stage FFL mast RL / NL ¥ ft/min (m/s) 82.0 / 99.0 (.42 / .50) 99.0 / 99.0 (.50 / .50) 106.0 / 106.0 (.54 / .54)
Opt. 3-stage FFL mast RL / NL ¥ ft/min (m/s) 87.0 / 105.0 (.44 / .53) 105.0 / 105.0 (.53 / .53) 113.0 / 113.0 (.57 / .57)
26 Lowering, standard mast RL / NL ¥ ft/min (m/s) 102.0 / 88.0 (.52 / .45) 102.0 / 88.0 (.52 / .45) 99.0 / 86.0 (.50 / .44)
Opt. 2-stage FFL mast RL / NL ¥ ft/min (m/s) 88.0 / 62.0 (.45 / .31) 88.0 / 62.0 (.45 / .31) 87.0 / 60.0 (.44 / .30)
Opt. 3-stage FFL mast RL / NL ¥ ft/min (m/s) 95.0 / 75.0 (.48 / .38) 95.0 / 75.0 (.48 / .38) 93.0 / 81.0 (.47 / .41)
27 Drawbar pull, 1 mph RL / NL (LP) lbf, (kN) 3,263 / 1,983 (14.5 / 8.8) 3,952 / 1,983 (17.6 / 8.8) 4,590 / 1,983 (20.4 / 8.8) 4,900 / 1,983 (21.8 / 8.8)
Drawbar pull, 1 mph RL / NL (Gas) lbf, (kN) 3,815 / 1,983 (17.0 / 8.8) 4,160 / 1,983 (18.5 / 8.8) 4,093 / 1,983 (18.2 / 8.8)
Drawbar pull, 3 mph RL / NL (LP) lbf, (kN) 2,092 / 1,983 (9.3 / 8.8) 2,500 / 1,983 (11.1 / 8.8) 3,200 / 1,983 (14.2 / 8.8) 3,600 / 1,983 (16.0 / 8.8)
Drawbar pull, 3 mph RL / NL (Gas) lbf, (kN) 2,500 / 1,983 (11.1 / 8.8) 2,750 / 1,983 (12.2 / 8.8) 2,600 / 1,983 (11.6 / 8.8) 3,400 / 1,983 (15.1 / 8.8)
28 Gradeability, 1 mph RL / NL (LP) % 23.6 / 23.5 29.0 / 23.5 34.2 / 23.5 36.8 / 23.5
Gradeability, 1 mph RL / NL (Gas) % 27.9 / 23.5 30.7 / 23.5 30.1 / 23.5
Gradeability, 3 mph RL / NL (LP) % 15.0 / 15.0 18.0 / 18.0 23.0 / 23.0 27.0 / 23.5
Gradeability, 3 mph RL / NL (Gas) % 17.4 / 17.4 20.0 / 20.0 20.0 / 20.0 23.5 / 23.5
30 Weight, total approximate, std. truck config. NL lb. (kg) 8,621 (3 910) 8,621 (3 910) 8,621 (3 910)
31 Axle loading, static, front / rear NL lb. (kg) 3,399 / 5,222 (1 542 / 2 369) 3,399 / 5,222 (1 542 / 2 369) 3,399 / 5,222 (1 542 / 2 369)
Axle loading, static, front / rear RL lb. (kg) 11,841 / 1,780 (5 371 / 807) 11,841 / 1,780 (5 371 / 807) 11,841 / 1,780 (5 371 / 807)
33 Size of tires, drive (front) / steer (rear) 21x7x15 / 16x5x10.5 21x7x15 / 16x5x10.5 21x7x15 / 16x5x10.5
34 Wheelbase in. (mm) 56.3 (1 430) 56.3 (1 430) 56.3 (1 430)
35 Tread, center of tires front / rear in. (mm) 35.1 (892) 35.1 (892) 35.1 (892)
36 Ground clearance, lowest point NL in. (mm) 3.6 (91) 3.6 (91) 3.6 (91)
37 Ground clearance, center wheelbase NL in. (mm) 4.9 (125) 4.9 (125) 4.9 (125)
38 Brakes, method of control, service / parking Foot / Hydraulic Foot / Hydraulic Foot / Hydraulic
39 Brakes, method of operation, service / parking Hand / Mechanical Hand / Mechanical Hand / Mechanical
40 Battery, volts / cold cranking amps V (amps) 12 / 475 12 / 475 12 / 475
42 Permanent output @ 2600 rpm LP / Gas hp (ps) 44 / 50 51 / 54 62 / 63
43 Torque at 1800 rpm LP / Gas lbf,/f (kg/m) 82.0 / 93.0 94.0 / 101.0 123.0 / 103.0
44 No. cylinders / displacement (cu.in.) / liters 4 / 122 / 2.0L 4 / 134 / 2.2L 4 / 146.5 / 2.4L
46 Gear change type Powershift Powershift Powershift
47 Number of speeds, forward / reverse 1 / 1 1 / 1 1 / 1 2 / 1
48 Transmission type Electronically Controlled Electronically Controlled Electronically Controlled
55 Relief pressure for attachments psi (kPA) 2,250 (15.5) 2,250 (15.5) 2,250 (15.5)
* CERTIFICATION: These Hyster lift trucks meet design specifications of Part II ANSI B56.1-1969, as required by OSHA Section 1910.178(a)(2) and also comply with Part III ANSI B56.1-revision in effect at time
of manufacture. Certification of compliance with the applicable ANSI standards appears on the lift truck.
† NOTE: Performance specifications/ratings are for truck equipped as described under Standard Equipment in this Technical Guide. Performance specifications are affected by the condition of the vehicle and how it
is equipped, as well as by the nature and condition of the operating area. Specifications are subject to change and you should discuss the proposed application with your authorized Hyster Dealer.
†† Limited by traction. For further information on this dimension, please contact your local Hyster Company dealer.
¥ Specifications given are for both LP and Gas where applicable unless otherwise noted.
5
Hyster S55FTS Lift Truck Specifications
PE
R
FO
R
M
AN
C
E

W
T.
TI
R
ES
&
W
H
EE
LS
PO
W
ER
TR
AI
N
D
IM
EN
SI
O
N
S
G
EN
ER
AL
1 Manufacturer Hyster Company Hyster Company Hyster Company
2 FortisTM Series, Model S55FTS (Fortis) S55FTS (Fortis Advance) S55FTS (Fortis Advance+)
Transmission Type Basic Electronic DuraMatchTM DuraMatch, DuraMatch Plus DuraMatch Plus2
3 Capacity, rated lb. (kg) 5,500 (2 495) 5,500 (2 495) 5,500 (2 495)
4 Load center in. (mm) 24 (610) 24 (610) 24 (610)
5 Engine / Power type Mazda 2.0L / LP, Gas Mazda 2.2L / LP, Gas GM 2.4 L / LP, Gas
6 Operator type Sit Sit Sit
7 Tire type, front / rear Cushion / Cushion Cushion / Cushion Cushion / Cushion
8 Wheels, front / rear (X=drive) 2X / 2 2X / 2 2X / 2
10 2-stg. LFL (TOF) in. (mm) 129 (3 292) 129 (3 292) 129 (3 292)
11 Limited free-lift (TOF) in. (mm) 5 (140) 5 (140) 5 (140)
12 Optional full free-lift (TOF) with / without LBE in. (mm) 36 / 62 (910 / 1 575) 36 / 62 (910 / 1 575) 36 / 62 (910 / 1 575)
13 Forks, thickness / width / length in. (mm) 1.6x3.9x42.0 (40x100x1 067) 1.6x3.9x42.0 (40x100x1 067) 1.6x3.9x42.0 (40x100x1 067)
14 Tilt angle, forward / backward Deg. ° 5 / 8 5 / 8 5 / 8
15 Length to face of forks in. (mm) 87.1 (2 213) 87.1 (2 213) 87.1 (2 213)
16 Width, standard tires / wide tread in. (mm) 43.6 / 48.9 (1 108 / 1 242) 43.6 / 48.9 (1 108 / 1 242) 43.6 / 48.9 (1 108 / 1 242)
17 Height, standard mast lowered in. (mm) 85 (2 135) 85 (2 135) 85 (2 135)
18 Height, std. mast extended with / without LBE in. (mm) 178 / 151 (4 515 / 3 840) 178 / 151 (4 515 / 3 840) 178 / 151 (4 515 / 3 840)
19 Turning radius, minimum outside in. (mm) 76.2 (1 937) 76.2 (1 937) 76.2 (1 937)
20 Center of wheel to face of forks in. (mm) 14.9 (378) 14.9 (378) 14.9 (378)
21 Right Angle Stack (Add load length for 90° stack) in. (mm) 91.1 (2 315) 91.1 (2 315) 91.1 (2 315)
22 Equal Intersecting Aisle (W=42 in., L=48 in.) in. (mm) 74.3 (1 888) 74.3 (1 888) 74.3 (1 888)
23 Stability (Comply with ANSI?) * YES YES YES
24 Travel speed RL / NL mph (km/h) 10.6 / 10.3 (17.0 / 16.6) 10.6 / 10.3 (17.0 / 16.6) 10.7 / 10.5 (17.2 / 16.9) 11.3 / 11.2 (18.3 / 18.0)
25 Lift speed, standard mast RL / NL ¥ ft/min (m/s) 104.0 / 110 (.53 / .56) 110.0 / 110.0 (.56 / .56) 119.0 / 119.0 (.60 / .60)
Opt. 2-stage FFL mast RL / NL ¥ ft/min (m/s) 93.0 / 110.0 (.47 / .56) 99.0 / 99.0 (.50 / .50) 106.0 / 106.0 (.54 / .54)
Opt. 3-stage FFL mast RL / NL ¥ ft/min (m/s) 99.0 / 110.0 (.50 / .56) 105.0 / 105.0 (.53 / .53) 113.0 / 113.0 (.57 / .57)
26 Lowering, standard mast RL / NL ¥ ft/min (m/s) 102.0 / 88.0 (.52 / .45) 102.0 / 88.0 (.52 / .45) 102.0 / 88.0 (.52 / .45)
Opt. 2-stage FFL mast RL / NL ¥ ft/min (m/s) 95.0 / 66.0 (.48 / .36) 95.0 / 66.0 (.48 / .36) 95.0 / 66.0 (.48 / .36)
Opt. 3-stage FFL mast RL / NL ¥ ft/min (m/s) 106.0 / 88.0 (.54 / .45) 106.0 / 88.0 (.54 / .45) 105.0 / 85.0 (.53 / .43)
27 Drawbar pull, 1 mph RL / NL (LP) lbf, (kN) 3,248 / 1,852 (14.5 / 8.2) 3,938 / 1,852 (17.5 / 8.2) 4,576 / 1,852 (20.4 / 8.2) 4,900 / 1,852 (21.8 / 8.2)
Drawbar pull, 1 mph RL / NL (Gas) lbf, (kN) 3,800 / 1,852 (16.9 / 8.2) 4,146 / 1,852 (18.4 / 8.2) 4,079 (1 850) / 1,852 (18.2 / 8.2)
Drawbar pull, 3 mph RL / NL (LP) lbf, (kN) 2,100 / 1,852 (9.3 / 8.2) 2,600 / 1,852 (11.6 / 8.2) 3,300 / 1,852 (14.7 / 8.2) 3,700 / 1,852 (16.5 / 8.2)
Drawbar pull, 3 mph RL / NL (Gas) lbf, (kN) 2,500 / 1,852 (11.1 / 8.2) 2,800 / 1,852 (12.5 / 8.2) 2,800 / 1,852 (12.5 / 8.2) 3,225 / 1,852 (14.4 / 8.2)
28 Gradeability, 1 mph RL / NL (LP) % 22.2 / 19.9 27.2 / 19.9 32.0 / 19.9 34.6 / 19.9
Gradeability, 1 mph RL / NL (Gas) % 26.2 / 19.9 28.8 / 19.9 28.2 / 19.9
Gradeability, 3 mph RL / NL (LP) % 14.0 / 14.0 16.9 / 16.9 21.5 / 19.9 25.0 / 19.9
Gradeability, 3 mph RL / NL (Gas) % 17.0 / 17.0 19.0 / 19.0 18.0 / 18.0 23.0 / 19.9
30 Weight, total approximate, std. truck config. NL lb. (kg) 9,223 (4 184) 9,223 (4 184) 9,223 (4 184)
31 Axle loading, static, front / rear NL lb. (kg) 3,442 / 5,781 (1 561 / 2 622) 3,442 / 5,781 (1 561 / 2 622) 3,442 / 5,781 (1 561 / 2 622)
Axle loading, static, front / rear RL lb. (kg) 12,728 / 1,994 (5 773 / 904) 12,728 / 1,994 (5 773 / 904) 12,728 / 1,994 (5 773 / 904)
33 Size of tires, drive (front) / steer (rear) 21x8x15 / 16x6x10.5 21x8x15 / 16x6x10.5 21x8x15 / 16x6x10.5
34 Wheelbase in. (mm) 56.3 (1 430) 56.3 (1 430) 56.3 (1 430)
35 Tread, center of tires front / rear in. (mm) 35.6 (905) 35.6 (905) 35.6 (905)
36 Ground clearance, lowest point NL in. (mm) 3.6 (91) 3.6 (91) 3.6 (91)
37 Ground clearance, center wheelbase NL in. (mm) 4.9 (125) 4.9 (125) 4.9 (125)
38 Brakes, method of control, service / parking Foot / Hydraulic Foot / Hydraulic Foot / Hydraulic
39 Brakes, method of operation, service / parking Hand / Mechanical Hand / Mechanical Hand / Mechanical
40 Battery, volts / cold cranking amps V (amps) 12 / 475 12 / 475 12 / 475
42 Permanent output @ 1800 rpm LP / Gas hp (ps) 44 / 50 51 / 54 62 / 63
43 Torque at 2600 rpm LP / Gas lbf,/f (kg/m) 82.0 / 93.0 94.0 / 101.0 123.0 / 103.0
44 No. cylinders / displacement (cu.in.) / liters 4 / 122 / 2.0L 4 / 134 / 2.2L 4 / 146.5 / 2.4L
46 Gear change type Powershift Powershift Powershift
47 Number of speeds, forward / reverse 1 / 1 1 / 1 1 / 1 2 / 1
48 Transmission type Electronically Controlled Electronically Controlled Electronically Controlled
55 Relief pressure for attachments psi (kPA) 2,250 (15.5) 2,250 (15.5) 2,250 (15.5)
* CERTIFICATION: These Hyster lift trucks meet design specifications of Part II ANSI B56.1-1969, as required by OSHA Section 1910.178(a)(2) and also comply with Part III ANSI B56.1-revision in effect at time
of manufacture. Certification of compliance with the applicable ANSI standards appears on the lift truck.
† NOTE: Performance specifications/ratings are for truck equipped as described under Standard Equipment in this Technical Guide. Performance specifications are affected by the condition of the vehicle and how it
is equipped, as well as by the nature and condition of the operating area. Specifications are subject to change and you should discuss the proposed application with your authorized Hyster Dealer.
†† Limited by traction. For further information on this dimension, please contact your local Hyster Company dealer.
¥ Specifications given are for both LP and Gas where applicable unless otherwise noted.
6
Hyster S60FT Lift Truck Specifications
PE
R
FO
R
M
AN
C
E

W
T.
TI
R
ES
&
W
H
EE
LS
PO
W
ER
TR
AI
N
D
IM
EN
SI
O
N
S
G
EN
ER
AL
1 Manufacturer Hyster Company Hyster Company Hyster Company
2 FortisTM Series, Model S60FT (Fortis) S60FT (Fortis Advance) S60FT (Fortis Advance+)
Transmission Type Basic Electronic DuraMatchTM DuraMatch, DuraMatch Plus DuraMatch Plus2
3 Capacity, rated lb. (kg) 6,000 (2 721) 6,000 (2 721) 6,000 (2 721)
4 Load center in. (mm) 24 (610) 24 (610) 24 (610)
5 Engine / Power type Mazda 2.0L / LP, Gas Mazda 2.2L / LP, Gas GM 2.4L / LP, Gas
6 Operator type Sit Sit Sit
7 Tire type, front / rear Cushion / Cushion Cushion / Cushion Cushion / Cushion
8 Wheels, front / rear (X=drive) 2X / 2 2X / 2 2X / 2
10 2-stg. LFL (TOF) in. (mm) 126 (3 209) 126 (3 209) 126 (3 209)
11 Limited free-lift (TOF) in. (mm) 5 (150) 5 (150) 5 (150)
12 Optional full free-lift (TOF) with / without LBE in. (mm) 36 / 59 (905 / 1 490) 36 / 59 (905 / 1 490) 36 / 59 (905 / 1 490)
13 Forks, thickness / width / length in. (mm) 1.6x3.9x42.0 (40x100x1 067) 1.6x3.9x42.0 (40x100x1 067) 1.6x3.9x42.0 (40x100x1 067)
14 Tilt angle, forward / backward Deg. ° 5 / 8 5 / 8 5 / 8
15 Length to face of forks in. (mm) 92.8 (2 356) 92.8 (2 356) 92.8 (2 356)
16 Width, standard tires / wide tread in. (mm) 43.6 / 48.9 (1 108 / 1 242) 43.6 / 48.9 (1 108 / 1 242) 43.6 / 48.9 (1 108 / 1 242)
17 Height, standard mast lowered in. (mm) 86 (2 185) 86 (2 185) 86 (2 185)
18 Height, std. mast extended with / without LBE in. (mm) 175 / 152 (4 435 / 3 855) 175 / 152 (4 435 / 3 855) 175 / 152 (4 435 / 3 855)
19 Turning radius, minimum outside in. (mm) 81.3(2 066) 81.3(2 066) 81.3(2 066)
20 Center of wheel to face of forks in. (mm) 15.2 (385) 15.2 (385) 15.2 (385)
21 Right Angle Stack (Add load length for 90° stack) in. (mm) 96.5 (2 451) 96.5 (2 451) 96.5 (2 451)
22 Equal Intersecting Aisle (W=42 in., L=48 in.) in. (mm) 76.7 (1 948) 76.7 (1 948) 76.7 (1 948)
23 Stability (Comply with ANSI?) * YES YES YES
24 Travel speed RL / NL mph (km/h) 10.6 / 10.3 (17.0 / 16.6) 10.6 / 10.3 (17.0 / 16.6) 10.7 / 10.5 (17.2 / 16.9) 11.3 / 11.2 (18.3 / 18.0)
25 Lift speed, standard mast RL / NL ¥ ft/min (m/s) 84.0 / 97.0 (.43 / .49) 97.0 / 97.0 (.49 / .49) 104.0 / 104.0 (.53 / .53)
Opt. 2-stage FFL mast RL / NL ¥ ft/min (m/s) 82.0 / 95.0 (.42 / .48) 95.0 / 95.0 (.48 / .48) 102.0 / 102.0 (.52 / .52)
Opt. 3-stage FFL mast RL / NL ¥ ft/min (m/s) 89.0 / 102.0 (.45 / .52) 102.0 / 102.0 (.52 / .52) 110.0 / 110.0 (.56 / .56)
26 Lowering, standard mast RL / NL ¥ ft/min (m/s) 102.0 / 88.0 (.52 / .45) 102.0 / 88.0 (.52 / .45) 102.0 / 88.0 (.52 / .45)
Opt. 2-stage FFL mast RL / NL ¥ ft/min (m/s) 98.0 / 66.0 (.50 / .34) 98.0 / 66.0 (.50 / .34) 98.0 / 66.0 (.50 / .34)
Opt. 3-stage FFL mast RL / NL ¥ ft/min (m/s) 107.0 / 88.0 (.54 / .45) 107.0 / 88.0 (.54 / .45) 107.0 / 85.0 (.54 / .43)
27 Drawbar pull, 1 mph RL / NL (LP) lbf, (kN) 3,225 / 1,892 (14.4 / 8.4) 3,915 / 1,892 (17.4 / 8.4) 4,553 / 1,892 (20.3 / 8.4) 4,900 / 1,892 (21.8 / 8.4)
Drawbar pull, 1 mph RL / NL (Gas) lbf, (kN) 3,778 / 1,892 (16.8 / 8.4) 4,123 / 1,892 (18.3 / 8.4) 4,056 / 1,892 (18.0 / 8.4) 4,900 / 1,892 (21.8 / 8.4)
Drawbar pull, 3 mph RL / NL (LP) lbf, (kN) 2,000 / 1,892 (8.9 / 8.4) 2,550 / 1,892 (11.3 / 8.4) 3,100 / 1,892 (13.8 / 8.4) 3,350 / 1,892 (11.8 / 8.4)
Drawbar pull, 3 mph RL / NL (Gas) lbf, (kN) 2,600 / 1,892 (11.5 / 8.4) 2,750 / 1,892 (12.2 / 8.4) 2,650 / 1,892 (11.8 / 8.4) 3,350 / 1,892 (11.8 / 8.4)
28 Gradeability, 1 mph RL / NL (LP) % 20.2 / 19.9 24.7 / 19.9 29.1 / 19.9 31.5 / 19.9
Gradeability, 1 mph RL / NL (Gas) % 23.8 / 19.9 26.1 / 19.9 25.7 / 19.9 31.5 / 19.9
Gradeability, 3 mph RL / NL (LP) % 12.7 / 12.7 16.0 / 16.0 20.0 / 19.9 20.2 / 19.9
Gradeability, 3 mph RL / NL (Gas) % 16.0 / 16.0 17.0 / 17.0 17.5 / 17.5 20.2 / 19.9
30 Weight, total approximate, std. truck config. NL lb. (kg) 9,838 (4 462) 9,838 (4 462) 9,838 (4 462)
31 Axle loading, static, front / rear NL lb. (kg) 3,516 / 6,322 (1 595 / 2 868) 3,516 / 6,322 (1 595 / 2 868) 3,516 / 6,322 (1 595 / 2 868)
Axle loading, static, front / rear RL lb. (kg) 13,698 / 2,140 (6 213 / 971) 13,698 / 2,140 (6 213 / 971) 13,698 / 2,140 (6 213 / 971)
33 Size of tires, drive (front) / steer (rear) 21x8x15 / 16x6x10.5 21x8x15 / 16x6x10.5 21x8x15 / 16x6x10.5
34 Wheelbase in. (mm) 56.3 (1 430) 56.3 (1 430) 56.3 (1 430)
35 Tread, center of tires front / rear in. (mm) 35.6 (905) 35.6 (905) 35.6 (905)
36 Ground clearance, lowest point NL in. (mm) 3.6 (91) 3.6 (91) 3.6 (91)
37 Ground clearance, center wheelbase NL in. (mm) 4.9 (125) 4.9 (125) 4.9 (125)
38 Brakes, method of control, service / parking Foot / Hydraulic Foot / Hydraulic Foot / Hydraulic
39 Brakes, method of operation, service / parking Hand / Mechanical Hand / Mechanical Hand / Mechanical
40 Battery, volts / cold cranking amps V (amps) 12 / 475 12 / 475 12 / 475
42 Permanent output @ 2600 rpm LP / Gas hp (ps) 44 / 50 51 / 54 62 / 63
43 Torque at 1800 rpm LP / Gas lbf,/f (kg/m) 82.0 / 93.0 94.0 / 101.0 123.0 / 103.0
44 No. cylinders / displacement (cu.in.) / liters 4 / 122 / 2.0L 4 / 134 / 2.2L 4 / 146.5 / 2.4L
46 Gear change type Powershift Powershift Powershift
47 Number of speeds, forward / reverse 1 / 1 1 / 1 1 / 1 2 / 1
48 Transmission type Electronically Controlled Electronically Controlled Electronically Controlled
55 Relief pressure for attachments psi (kPA) 2,250 (15.5) 2,250 (15.5) 2,250 (15.5)
* CERTIFICATION: These Hyster lift trucks meet design specifications of Part II ANSI B56.1-1969, as required by OSHA Section 1910.178(a)(2) and also comply with Part III ANSI B56.1-revision in effect at time
of manufacture. Certification of compliance with the applicable ANSI standards appears on the lift truck.
† NOTE: Performance specifications/ratings are for truck equipped as described under Standard Equipment in this Technical Guide. Performance specifications are affected by the condition of the vehicle and how it
is equipped, as well as by the nature and condition of the operating area. Specifications are subject to change and you should discuss the proposed application with your authorized Hyster Dealer.
†† Limited by traction. For further information on this dimension, please contact your local Hyster Company dealer.
¥ Specifications given are for both LP and Gas where applicable unless otherwise noted.
7
Hyster S70FT Lift Truck Specifications
PE
R
FO
R
M
AN
C
E

W
T.
TI
R
ES
&
W
H
EE
LS
PO
W
ER
TR
AI
N
D
IM
EN
SI
O
N
S
G
EN
ER
AL
40 Battery, volts / cold cranking amps V (amps) 12 / 475 12 / 475 12 / 475
42 Permanent output @ 2600 rpm LP / Gas hp (ps) 51 / 54 62 / 63 62 / 63
43 Torque at 1800 rpm LP / Gas lbf,/f (kg/m) 82.0 / 101.0 123.0 / 103.0 123.0 / 103.0
44 No. cylinders / displacement (cu.in.) / liters 4 / 122 / 2.0L 4 / 146.5 / 2.4L 4 / 146.5 / 2.4L
46 Gear change type Powershift Powershift Powershift
47 Number of speeds, forward / reverse 1 / 1 1 / 1 1 / 1 2 / 1
48 Transmission type Electronically Controlled Electronically Controlled Electronically Controlled
55 Relief pressure for attachments psi (kPA) 2,250 (15.5) 2,250 (15.5) 2,250 (15.5)
10 2-stg. LFL (TOF) in. (mm) 126 (3 209) 126 (3 209) 126 (3 209)
11 Limited free-lift (TOF) in. (mm) 5 (150) 5 (150) 5 (150)
12 Optional full free-lift (TOF) with / without LBE in. (mm) 36 / 59 (905 / 1 490) 36 / 59 (905 / 1 490) 36 / 59 (905 / 1 490)
13 Forks, thickness / width / length in. (mm) 1.6x3.9x42.0 (40x100x1 067) 1.6x3.9x42.0 (40x100x1 067) 1.6x3.9x42.0 (40x100x1 067)
14 Tilt angle, forward / backward Deg. ° 5 / 8 5 / 8 5 / 8
15 Length to face of forks in. (mm) 94.7 (2 406) 94.7 (2 406) 94.7 (2 406)
16 Width, standard tires / wide tread in. (mm) 46.0 / 48.9 (1 158 / 1 242) 46.0 / 48.9 (1 158 / 1 242) 46.0 / 48.9 (1 158 / 1 242)
17 Height, standard mast lowered in. (mm) 86 (2 185) 86 (2 185) 86 (2 185)
18 Height, std. mast extended with / without LBE in. (mm) 175 / 152 (4 435 / 3 855) 175 / 152 (4 435 / 3 855) 175 / 152 (4 435 / 3 855)
19 Turning radius, minimum outside in. (mm) 83.4 (2 119) 83.4 (2 119) 83.4 (2 119)
20 Center of wheel to face of forks in. (mm) 15.2 (385) 15.2 (385) 15.2 (385)
21 Right Angle Stack (Add load length for 90° stack) in. (mm) 98.6 (2 504) 98.6 (2 504) 98.6 (2 504)
22 Equal Intersecting Aisle (W=42 in., L=48 in.) in. (mm) 78.4 (1 991) 78.4 (1 991) 78.4 (1 991)
23 Stability (Comply with ANSI?) * YES YES YES
24 Travel speed RL / NL (LP) mph (km/h) 10.6 / 10.3 (17 / 16.6) 10.7 / 10.5 (17.2 / 16.9) 10.7 / 10.5 (17.2 / 16.9) 11.3 / 11.2 (18.3 / 18.0)
25 Lift speed, standard mast RL / NL (LP) ft/min (m/s) 88.0 / 97.0 (.45 / .49) 104.0 / 104.0 (.53 / .53) 104.0 / 104.0 (.53 / .53)
Lift speed, standard mast RL / NL (Gas) ft/min (m/s) 93.0 / 97.0 (.47 / .49) 94.0 / 104.0 (.48 / .53) 94.0 / 104.0 (.48 / .53)
Opt. 2-stage FFL mast RL / NL (LP) ft/min (m/s) 86.0 / 95.0 (.44 / .48) 102.0 / 102.0 (.52 / .52) 102.0 / 102.0 (.52 / .52)
Opt. 2-stage FFL mast RL / NL (Gas) ft/min (m/s) 91.0 / 95.0 (.46 / .48) 92.0 / 102.0 (.47 / .52) 92.0 / 102.0 (.47 / .52)
Opt. 3-stage FFL mast RL / NL (LP) ft/min (m/s) 93.0 / 102.0 (.47 / .52) 110.0 / 110.0 (.56 / .56) 110.0 / 110.0 (.56 / .56)
Opt. 3-stage FFL mast RL / NL (Gas) ft/min (m/s) 99.0 / 102.0 (.50 / .52) 100.0 / 110.0 (.51 / .56) 100.0 / 110.0 (.51 / .56)
26 Lowering, standard mast RL / NL ¥ ft/min (m/s) 102.0 / 88.0 (.52 / .45) 102.0 / 88.0 (.52 / .45) 102.0 / 88.0 (.52 / .45)
Opt. 2-stage FFL mast RL / NL ¥ ft/min (m/s) 98.0 / 66.0 (.50 / .34) 98.0 / 66.0 (.50 / .34) 98.0 / 66.0 (.50 / .34)
Opt. 3-stage FFL mast RL / NL ¥ ft/min (m/s) 107.0 / 88.0 (.54 / .45) 107.0 / 88.0 (.54 / .45) 107.0 / 85.0 (.54 / .43)
27 Drawbar pull, 1 mph RL / NL (LP) lbf, (kN) 3,822 / 1,702 (17.0 / 7.6) 4,520 / 1,702 (20.1 / 7.6) 4,520 / 1,702 (20.1 / 7.6) 4,900 / 1,702 (21.8 / 7.6)
Drawbar pull, 1 mph RL / NL (Gas) lbf, (kN) 4,090 / 1,702 (18.2 / 7.6) 4,023 / 1,702 (17.9 / 7.6) 4,023 / 1,702 (17.9 / 7.6)
Drawbar pull, 3 mph RL / NL (LP) lbf, (kN) 2,600 / 1,702 (11.6 / 7.6) 3,000 / 1,702 (13.4 / 7.6) 3,000 / 1,702 (13.4 / 7.6) 3,700 / 1,702 (16.5 / 7.6)
Drawbar pull, 3 mph RL / NL (Gas) lbf, (kN) 2,700 / 1,702 (12.0 / 7.6) 2,600 / 1,702 (11.6 / 7.6) 2,600 / 1,702 (11.6 / 7.6) 3,200 / 1,702 (14.2 / 7.6)
28 Gradeability, 1 mph RL / NL (LP) % 21.8 / 16.5 25.7 / 16.5 25.7 / 16.5 28.0 / 16.5
Gradeability, 1 mph RL / NL (Gas) % 23.1 / 16.5 22.7 / 16.5 22.7 / 16.5 28.0 / 16.5
Gradeability, 3 mph RL / NL (LP) % 14.0 / 14.0 17.0 / 16.5 17.0 / 16.5 21.0 / 16.5
Gradeability, 3 mph RL / NL (Gas) % 15.0 / 15.0 15.0 / 15.0 15.0 / 15.0 17.5 / 16.5
1 Manufacturer Hyster Company Hyster Company Hyster Company
2 FortisTM Series, Model S70FT (Fortis) S70FT (Fortis Advance) S70FT (Fortis Advance+)
Transmission Type Basic Electronic DuraMatchTM DuraMatchTM Plus DuraMatch Plus2
3 Capacity, rated lb. (kg) 7,000 (3 175) 7,000 (3 175) 7,000 (3 175)
4 Load center in. (mm) 24 (610) 24 (610) 24 (610)
5 Engine / Power type Mazda 2.2L / LP, Gas GM 2.4L / LP, Gas GM 2.4L / LP, Gas
6 Operator type Sit Sit Sit
7 Tire type, front / rear Cushion / Cushion Cushion / Cushion Cushion / Cushion
8 Wheels, front / rear (X=drive) 2X / 2 2X / 2 2X / 2
30 Weight, total approximate, std. truck config. NL lb. (kg) 10,604 (4 810) 10,604 (4 810) 10,604 (4 810)
31 Axle loading, static, front / rear NL lb. (kg) 3,310 / 7,294 (1 501 / 3 309) 3,310 / 7,294 (1 501 / 3 309) 3,310 / 7,294 (1 501 / 3 309))
Axle loading, static, front / rear RL lb. (kg) 15,189 / 2,415 (6 890 / 1 095)15,189 / 2,415 (6 890 / 1 095) 15,189 / 2,415 (6 890 / 1 095)
* CERTIFICATION: These Hyster lift trucks meet design specifications of Part II ANSI B56.1-1969, as required by OSHA Section 1910.178(a)(2) and also comply with Part III ANSI B56.1-revision in effect at time
of manufacture. Certification of compliance with the applicable ANSI standards appears on the lift truck.
† NOTE: Performance specifications/ratings are for truck equipped as described under Standard Equipment in this Technical Guide. Performance specifications are affected by the condition of the vehicle and how it
is equipped, as well as by the nature and condition of the operating area. Specifications are subject to change and you should discuss the proposed application with your authorized Hyster Dealer.
†† Limited by traction. For further information on this dimension, please contact your local Hyster Company dealer.
¥ Specifications given are for both LP and Gas where applicable unless otherwise noted.
33 Size of tires, drive (front) / steer (rear) 21x9x15 / 16x6x10.5 21x9x15 / 16x6x10.5 21x9x15 / 16x6x10.5
34 Wheelbase in. (mm) 56.3 (1 430) 56.3 (1 430) 56.3 (1 430)
35 Tread, center of tires front / rear in. (mm) 36.7 (929) 36.7 (929) 36.7 (929)
36 Ground clearance, lowest point NL in. (mm) 3.6 (91) 3.6 (91) 3.6 (91)
37 Ground clearance, center wheelbase NL in. (mm) 4.9 (125) 4.9 (125) 4.9 (125)
38 Brakes, method of control, service / parking Foot / Hydraulic Foot / Hydraulic Foot / Hydraulic
39 Brakes, method of operation, service / parking Hand / Mechanical Hand / Mechanical Hand / Mechanical
RATED LOAD vs. LOAD CENTER
INTEGRAL SIDESHIFT ATTACHMENT
U. S. CUSTOMARY
RATED LOAD vs. LOAD CENTER
STANDARD CARRIAGE
U. S. CUSTOMARY
Hyster S40-70FT Lift Truck Rated Capacities
RA
TE
D
LO
AD
(lb
s) 3,000
00 10 20 30 40 50 60
4,000
5,000
6,000
7,000
8,000
LOAD CENTER (in)
RA
TE
D
LO
AD
(lb
s) LOAD CENTER (in)
RATED LOAD vs. LOAD CENTER
INTEGRAL SIDESHIFT ATTACHMENT
METRIC
RATED LOAD vs. LOAD CENTER
STANDARD CARRIAGE
METRIC
RA
TE
D
LO
AD
(lb
s) LOAD CENTER (in)
RA
TE
D
LO
AD
(lb
s) LOAD CENTER (in)
2500 500 750 1 000 1 250 1 500
1 000
1 500
2 000
2 500
3 000
3 500
S70FT
S60FT
S55FTS
S50FT
8 00 10 20 30 40 50 60
2500 500 750 1 000 1 250 1 500
1 000
1 500
2 000
2 500
3 000
3 500
S70FT
S60FT
S55FTS
S50FT
S70FT
S60FT
S55FTS
S50FT
S70FT
S60FT
S55FTS
S50FT
2,000
S40FT
3,000
4,000
5,000
6,000
7,000
8,000
2,000
S40FT
500
S40FT S40FT
Hyster S40-70FT Mast Specifications
S40-55FT, 55FTS MAST DIMENSIONS in. (mm)
Maximum Overall Overall Extended Height Free-Lift (TOF) Approx. Total Wgt. of Standard Equipped Truck w/o Load
Fork Height Lowered with Load without Load without load S40FT S50FT S55FTS
(Top of Forks) † Height Backrest Ext. Backrest Ext. Backrest Ext.* lb. (kg) lb. (kg) lb. (kg)
2-STAGE LIMITED FREE-LIFT (LFL) VISTA®
82 (2 092) 61 (1 535) 131 (3 315) 104 (2 650) 5 (140) 7,621 (3 457) 8,404 (3 812) 9,008 (4 086)
129 (3 292) 85 (2 135) 178 (4 515) 151 (3 840) 5 (140) 7,837 (3 555) 8,621 (3 910) 9,223 (4 184)
2-STAGE FULL FREE-LIFT (FFL) VISTA®
130 (3 302) 85 (2 135) 179 (4 525) 152 (3 860) 62 (1 575) 7,875 (3 572) 8,658 (3 927) 9,262 (4 201)
3-STAGE FULL FREE-LIFT (FFL) VISTA®
171 (4 350) 77 (1 935) 220 (5 575) 193 (4 890) 54 (1 395) 8,117 (3 682) 8,900 (4 037) 9,504 (4 311)
189 (4 800) 83 (2 085) 238 (6 025) 210 (5 340) 60 (1 545) 8,192 (3 716) 8,975 (4 071) 9,579 (4 345)
194 (4 950) 85 (2 135) 244 (6 175) 216 (5 490) 62 (1 595) 8,217 (3 727) 9,000 (4 082) 9,603 (4 356)
200 (5 100) 88 (2 235) 249 (6 325) 222 (5 640) 66 (1 695) 8,263 (3 748) 9,046 (4 103) 9,650 (4 377)
218 (5 550) 94 (2 385) 267 (6 775) 240 (6 090) 84 (2 145) 8,345 (3 785) 9,127 (4 140) 9,731 (4 414)
4-STAGE FULL FREE-LIFT (FFL) VISTA® ¥
240 (6 095) 84 (2 135) 289 (7 321) 262 (6 641) 59 (1 513) 8,759 (3 973) 9,542 (4 328) 10,146 (4 602)
276 (7 013) 96 (2 437) 322 (8 184) 298 (7 556) 71 (1 817) 8,955 (4 062) 9,738 (4 417) 10,342 (4 691)
† Lift heights over 171.5” (4 356 mm) maximum fork height are considered highlifts and require reduced capacity and restricted back tilt.
* On 2-stage FFL and 3-stage FFL VISTA® mast, subtract 26” (665 mm) if Load Backrest Extension (LBE) is used.
¥ Lift trucks equipped with the 4-stage FFL VISTA® mast require Class II carriage and forks.
S60-70FT MAST DIMENSIONS in. (mm)
Maximum Overall Overall Ext. Height Free-Lift (TOF) Approximate Total Weight of Standard
Fork Height Lowered with Load without Load without Load Equipped Truck w/o Load
(Top of Forks) † Height Backrest Ext. Backrest Ext. Backrest Ext.* S60FT lb. (kg) S70FT lb. (kg)
2-STAGE LIMITED FREE-LIFT (LFL) VISTA®
126 (3 209) 86 (2 185) 175 (4 435) 152 (3 855) 5 (150) 9,838 (4 462) 10,604 (4 810)
2-STAGE FULL FREE-LIFT (FFL) VISTA®
122 (3 110) 85 (2 135) 171 (4 335) 148 (3 755) 58 (1 490) 9,857 (4 471) 10,624 (4 819)
130 (3 310) 88 (2 235) 179 (4 535) 156 (3 955) 62 (1 590) 9,892 (4 487) 10,659 (4 835)
3-STAGE FULL FREE-LIFT (FFL) VISTA®
181 (4 618) 85 (2 135) 231 (5 845) 207 (5 245) 59 (1 505) 10,196 (4 625) 10,964 (4 973)
187 (4 768) 88 (2 235) 236 (5 995) 212 (5 395) 63 (1 595) 10,241 (4 645) 11,008 (4 993)
211 (5 368) 98 (2 485) 260 (6 595) 236 (5 995) 73 (1 855) 10,375 (4 706) 11,142 (5 054)
229 (5 818) 104 (2 635) 278 (7 045) 254 (6 445) 79 (2 005) 10,565 (4 792) 11,332 (5 140)
4-STAGE FULL FREE-LIFT (FFL) VISTA® ¥ (S60FT Only)
240 (6 095) 84 (2 135) 289 (7 321) 262 (6 641) 59 (1 513) 10,580 (4 799) N / A
276 (7 013) 96 (2 437) 322 (8 184) 298 (7 556) 71 (1 817) 10,776 (4 888) N / A
† Lift heights over 164.0” (4 166 mm) maximum fork height are considered highlifts and require reduced capacity and restricted back tilt.
* On 2-stage FFL and 3-stage VISTA® mast, subtract 23” (585 mm) if Load Backrest Extension (LBE) is used.
¥ Lift trucks equipped with the 4-stage FFL VISTA® mast require Class II carriage and forks.
9
STANDARD EQUIPMENT
FortisTM Package
Complete truck equipped with:
• Mazda 2.0L emissions compliant engine
(S40-50FT, S55FTS, S60FT)
• Mazda 2.2L emissions compliant engine
(S70FT)
• Basic electronic powershift transmission
- Electronic inching
- Electronic shift control
- Neutral start switch
- Anti-restart protection
• MONOTROL® pedal
• 2-stage limited free-lift VISTA® mast with maximum fork
height of 129.0" (3 277 mm) (S40-50FT, S55FTS) or
126.0" (3 209 mm) (S60-70FT)
• 38.5" (978 mm) wide hook-type carriage with load
backrest extension
• 42.0" (1 067 mm) long forks
• 5 degrees forward and 8 degrees backward mast tilt
• 3-function valve
• Integrated dashboard display includes:
- LCD Display:
-- Fuel level
-- Hour meter
-- Coolant Temp
-- Clock
-- Messages
- Service Indicator Lights:
-- Alternator
-- Transmission oil temperature
-- Engine oil pressure
-- Brake fluid level
-- Fasten seatbelt
-- Low fuel level
-- Engine malfunction
-- System malfunction
-- Park brake
-- Coolant temp
-- Forward & Reverse Direction
-- Neutral
• Hydraulic power steering (Hydrostatic)
• Non-suspension vinyl seat
• Electronic horn
• Infinitely adjustable steer column
• Rubber floor mat
• High air intake
• Integral tie downs
• Operator restraint system with No Cinch ELR seatbelt
• Serpentine core radiator
• Single pedal inch brake
• Hyster stability mechanism
• Cowl-mounted hydraulic hand levers
• Swing out LPG tank bracket
• 84” (2 128 mm) Overhead guard
• 12 months / 2,000 hours manufacturer’s warranty
• 24 months / 4,000 hours manufacturer’s powertrain
warranty
• Operator’s manual
• UL Classification LP
STANDARD EQUIPMENT
FortisTM Advance
Complete truck equipped with:
• Mazda 2.2L emissions compliant engine (S40-60FT)
• GM 2.4L emissions compliant engine (S70FT)
• DuraMatchTM transmission
- Electronic inching
- Electronic shift control
- Neutral start switch
- Anti-restart protection
- Auto deceleration system
- Controlled power reversal
- Controlled roll back on ramps
• MONOTROL® pedal
• 2-stage limited free-lift VISTA® mast with maximum fork
height of 129.0" (3 277 mm) (S40-50FT, S55FTS) or
126.0" (3 209 mm) (S60-70FT)
• 38.5" (978 mm) wide hook-type carriage with load
backrest extension
• 42.0" (1 067 mm) long forks
• 5 degrees forward and 8 degrees backward mast tilt
• 3-function valve
• Integrated dashboard display includes:
- LCD Display:
-- Fuel level
-- Hour meter
-- Coolant Temp
-- Clock
-- Messages
- Service Indicator Lights:
-- Alternator
-- Transmission oil temperature
-- Engine oil pressure
-- Brake fluid level
-- Fasten seatbelt
-- Low fuel level
-- Engine malfunction
-- System malfunction
-- Park brake
-- Coolant temp
-- Forward & Reverse Direction
-- Neutral
• Hydraulic power steering (Hydrostatic)
• Non-suspension vinyl seat
• Electronic horn
• Infinitely adjustable steer column
• Rubber floor mat
• High air intake
• Integral tie downs
• Operator restraint system with No Cinch ELR seatbelt
• Heavy duty anti clog radiator
• Single pedal inch brake
• Hyster stability mechanism
• Cowl-mounted hydraulic hand levers
• Swing out LPG tank bracket
• 84” (2 128 mm) Overhead guard
• 12 months / 2,000 hours manufacturer’s warranty
• 24 months / 4,000 hours manufacturer’s powertrain
warranty
• Operator’s manual
• UL Classification LP
STANDARD EQUIPMENT
FortisTM Advance+
Complete truck equipped with:
• GM 2.4L LPG and Gas emissions compliant engine
• DuraMatchTM, DuraMatchTM Plus, DuraMatchTM Plus2 transmission
- Electronic inching
- Electronic shift control
- Neutral start switch
- Anti-restart protection
- Auto deceleration system
- Controlled power reversal
- Controlled roll back on ramps
- Auto-speed hydraulics (N/A for DuraMatch)
- Throttle response management (N/A for DuraMatch)
- Extended drawbar pull capability (DuraMatch Plus2)
• TouchPointTM or TouchControlTM hydraulics (required with
DuraMatch Plus or DuraMatch Plus 2)
• MONOTROL® pedal
• 2-stage limited free-lift VISTA® mast with maximum fork
height of 129.0" (3 277 mm) (S40-50FT, S55FTS) or
126.0" (3 209 mm) (S60-70FT)
• 38.5" (978 mm) wide hook-type carriage with load
backrest extension
• 42.0" (1 067 mm) long forks
• 5 degrees forward and 8 degrees backward mast tilt
• 3-function valve
• Integrated dashboard display includes:
- LCD Display:
-- Fuel level
-- Hour meter
-- Coolant Temp
-- Clock
-- Messages
- Service Indicator Lights:
-- Alternator
-- Transmission oil temperature
-- Engine oil pressure
-- Brake fluid level
-- Fasten seatbelt
-- Low fuel level
-- Engine malfunction
-- System malfunction
-- Park brake
-- Coolant temp
-- 1st Gear Locking
-- Forward & Reverse Direction
-- Neutral
• Hydraulic power steering (Hydrostatic)
• Full-suspension vinyl or cloth seat
• Electronic horn
• Infinitely adjustable steer column
• Rubber floor mat
• High air intake
• Integral tie downs
• Operator restraint system with No Cinch ELR seatbelt
• Combi-cooler radiator
• Single pedal inch brake
• Hyster stability mechanism
• Swing out LPG tank bracket
• 84” (2 128 mm) Overhead guard
• 12 months / 2,000 hours manufacturer’s warranty
• 24 months / 4,000 hours manufacturer’s powertrain
warranty
• Operator’s manual
• UL Classification LP
Hyster S40-70FT Standard Features and Options
10
OPTIONAL EQUIPMENT
• Gasoline powered 2.0 & 2.2L engines
• Powertrain protection system
• Premium electronic monitoring
• High air intake with precleaner
• Accumulator
• Keyless start (with auxiliary key switch)
• Drive lights and rear work lights with halogen bulbs
• Auto-deceleration system (N/A with Fortis Pkg.)
• Extended drawbar pull capability (DuraMatchTM Plus2)
• Controlled power reversal feature (N/A with Fortis Pkg.)
• Controlled roll back on ramps (N/A with Fortis Pkg.)
• Auto-speed hydraulics (DuraMatch Plus)
• Heavy duty radiator with combi cooler (N/A with Fortis Pkg.)
• Throttle response management (DuraMatch Plus,
DuraMatch Plus2)
• Paper Applications kit
• Vented hood
• Swing-out, drop-down EZXchangeTM LPG tank bracket
• TouchPointTM hydraulics with fully adjustable armrest
• TouchControlTM hydraulic control handle
• Return to set tilt
• Rear drive handle with horn button
• Semi-suspension seat - vinyl or cloth
• Full suspension seat - vinyl or cloth
• Swivel full-suspension seat - vinyl or cloth
• Dual inch brake pedals
• Password protection
• Alarm - Reverse activated 82-102 dB(A)-Self-adjusting
• Amber strobe light - continuous activated, OHG mounted
• Various light packages
- Two LED brake/back-up lights
- Two front and one rear work lights
- Two front, one rear work light and two LED
brake/tail/back-up lights
• Parts publications - printed or CD, serial number specific
• UL Classification GS or LPS
• Operator Preshift Checklist
• Impact Monitor
• Load Weight Display
Hyster S40-70FT Standard Features and Options
CAPACITY:
Model S40FT: 4,000 lbs. at 24” (1 814 kg at 610 mm) load center.
Model S50FT: 5,000 lbs. at 24” (2 268 kg at 610 mm) load center.
Model S55FTS: 5,500 lbs. at 24” (2 495 kg at 610 mm) load center.
Model S60FT: 6,000 lbs. at 24” (2 721 kg at 610 mm) load center.
Model S70FT: 7,000 lbs. at 24” (3 175 kg at 610 mm) load center.
Rated capacities are for trucks equipped with:
• 3-stage full free-lift VISTA® mast to 171.5" (4 356 mm) maximum fork height for
S40-50FT, S55FTS or 164.0" (4 166 mm) for S60-70FT.
• 38.5" (978 mm) hook-type carriage with 42.0" (1 067 mm) long forks as required for
S40-50FT, S55FTS or 48.0” (1 219 mm) for S60-70FT.
• Load backrest extension (LBE)
MASTS
Masts are available in 2-stage limited free lift and 2, 3,
or 4-stage full free-lift VISTA® masts.
Masts feature flush-faced, nested-channel design and
full-radius, angled load rollers.
CARRIAGE
Carriages are hook-type, ITA Class II mounting
(S40-50FT, S55FTS), ITA Class III (S60-70FT). Overall
width without load backrest extension (LBE) is 38.5”
(978 mm); with LBE is 39.72” (1 009 mm). Minimum
inside-to-inside fork spacing is 0.12” (3 mm). Maximum
outside-to-outside fork spacing is 38.33” (974 mm).
FORKS
S40-50FT, S55FTS lift trucks feature:
1.6” x 3.9” x 36.0” to 60.0”
(40 x 100 x 914 to 1 525 mm) long pallet forks.
S60-70FT lift trucks feature:
2.0” x 4.9” x 36.0” to 72.0”
(50 x 125 x 915 to 1 830 mm) long pallet forks.
Polished and tapered forks are also available.
ENGINES
Three engines are available for the S40-70FT models the Mazda emissions compliant 2.0L and 2.2L engines and
the GM 2.4L emissions compliant engine. The engine
configurations are specified as follows: The Fortis package
configuration uses the Mazda FE 2.0L engine, the Fortis
Advance uses the Mazda F2 2.2L engine (S40-60FT) and
the GM 2.4L engine (S70FT only) and the Fortis Advance+
uses the GM 2.4L engine.
Mazda 2.0L and 2.2L emissions compliant engines
feature:
• 4-cylinder overhead valve and overhead camshaft
design
• Cast iron block, aluminum cylinder head with hardened
exhaust valve seats
• Electronically controlled fuel systems
• Spin-on full flow oil filter
• Electronic governor
• Heavy-duty air cleaner with pre-cleaner
• Engine Control Unit (ECU)
• Three-way catalytic converter exhaust system
• 2.0L LP engine produces 44 h.p. @ 2600 rpm
• 2.2L LP engine produces 51 h.p. @ 2600 rpm
• 2.0L Gas engine produces 50 h.p. @ 2600 rpm
• 2.2L Gas engine produces 54 h.p. @ 2600 rpm
GM 2.4L emissions compliant engine features:
• 4-cylinder overhead valve and overhead camshaft
design
• Cast iron block, aluminum cylinder head with hardened
intake valve and exhaust valve seats, and hydraulic lifters
• Electronically controlled fuel system - Direct port fuel in
• Spin-on full flow oil filter
• Drive-by-wire throttle control
• Electronic governor
• Heavy-duty air cleaner with pre-cleaner
• Engine Control Unit (ECU)
• Three-way catalytic converter exhaust system
• 2.4L engine produces 61.0 horse power @ 2600 rpm
TRANSMISSION
• Standard Electronic Powershift: Single range powershift,
electronic inching (requires no adjustment), electric
shift control, neutral start switch, and anti-restart
protection.
• DuraMatchTM : All of the features of the standard
electronic transmission plus Auto Deceleration System,
controlled power reversal, controlled roll back on ramps.
• DuraMatchTM Plus: All of the features of the DuraMatch
as well as Auto Speed Hydraulics and Throttle Response
Management System.
• DuraMatchTM Plus2: All of the features of the DuraMatch
Plus as well as 2-speed functionality for extended
drawbar pull capability.
COOLING SYSTEM
• Multiple cooling system designs, depending on engine
and transmission configuration:
• Serpentine core
• Square-wave anti-clog
• Heavy duty square-wave anti-clog
• Square-wave anti-clog Combi-cooler
• All radiators utilize cross-flow aluminum cores, pusher
type fans and permanently lubricated water pump.
• “Knife-edge” type fan shrouds that direct air flow through
the counterweight air passages.
• 15 psi operating system pressure.
• Combi-cooler contains an externally mounted
transmission oil cooler to aid in heat dissipation.
ELECTRICAL SYSTEM
• CANbus control system simplifies truck wiring and
enhances truck dependability.
• IPP 66 sealed automotive style electrical connectors.
• Standardized wire routing, all wires are color coded, and
marked with numbers for easy identification.
• Vehicle System Manager (VSM) directly or indirectly
controls all electrical functions except those controlled
by the Engine Control Unit (ECU).
• 12-volt maintenance free battery provides 475 cold
cranking amps.
• Onboard diagnostics monitoring and feedback.
HYDRAULIC SYSTEM
Manual Hydraulic Control Valve & Electro-Hydraulic
Control Valve
• S40-60FT, S55FTS: hydraulic lift system operates at
3,100 psi (21.4 Mpa).
• S70FT: hydraulic lift system operates at 3,400 psi
(23.4 Mpa).
• Tilt and auxiliary systems have 2,250 psi (15.5 Mpa)
relief pressure in all valve variations.
• Hydraulic system is protected by a replaceable ten
micron paper element in-tank filter assembly.
• Hydraulic breather filter includes an anti-splash baffle and
is rated at three micron absolute.
• 100 mesh suction line strainer.
• O-Ring face seal fittings with captive O-Ring grooves are
used on all high pressure connections.
• Emergency lowering valve allows load to be lowered in the
event of battery power loss.
STEER AXLE / STEER SYSTEM
• Equal-area, double-ended, hydrostatic steering cylinder
is mounted in cast ductile iron axle frame.
• Elastomeric axle mounts absorb shock and allow
lubrication free articulation.
• Axle assembly utilizes synthetic boots and seals to retain
lubricants and shield components against destructive grit
and reduce lube points.
• Wheel hubs rotate on large, tapered roller bearings.
• Top spindle bearings lubricated through easy access
lube fittings.
• Hydrostatic steer system provides smooth, precise
steering with only 4 turns lock-to-lock.
• Hyster stability mechanism enhances lateral stability by
limiting steer axle articulation without a compromise in
uneven surface travel.
BRAKES
• Asbestos free, self-energizing, automatically adjusting
drum brake assemblies.
• Dual circuit master cylinder with sealed fluid reservoir
and magnetic fluid level sensor.
• Ratchet-type, hand-activated parking brake lever allows
controlled application.
OPERATOR COMPARTMENT
• Cowl mounted hydraulic hand levers.
• TouchPointTM electro-hydraulic seat side mini-levers
(optional).
• TouchControlTM hydraulic seat side joystick (optional).
• Twelve inch textured steering wheel with hand spinner
knob.
• Automotive style foot controls with single braking/inching
pedal (dual pedals are optional).
• Integrated dashboard display is backlit, allowing easy
visibility under all lighting conditions.
• Grid-style overhead guard offers superb visibility at
extended heights.
• Infinitely adjustable tilt steer column.
• Optimal 13.8” entry step height on both sides of the truck.
• MONOTROL® pedal controls engine speed and truck
direction, freeing operator’s hands to operate steering
and hydraulic levers.
Special attachments, equipment or accessories not
listed above may be available through Applications
Engineering for specific application requirements.
11
Hyster Company
P.O. Box 7006
Greenville, North Carolina
27835-7006
Part No.: S4-70FT/TG
1/2006 Litho in U.S.A.
Visit us online at www.hysterusa.com or call us at 1-800-HYSTER-1.
Hyster, , SpaceSaver, VISTA and MONOTROL are registered trademarks of Hyster Company.
Fortis, DuraMatch, Pacesetter VSM, TouchPoint, TouchControl, Challenger, and are trademarks of
Hyster Company. Hyster products are subject to change without notice.
The Hyster Company products included in this document may be covered
by US Patent 6,684,148, and other patents pending.

PDF Document reader online

This website is focused on providing document in readable format, online without need to install any type of software on your computer. If you are using thin client, or are not allowed to install document reader of particular type, this application may come in hand for you. Simply upload your document, and Docureader.top will transform it into readable format in a few seconds. Why choose Docureader.top?

  1. Unlimited sharing - you can upload document of any size. If we are able to convert it into readable format, you have it here - saved for later or immediate reading
  2. Cross-platform - no compromised when reading your document. We support most of modern browers without the need of installing any of external plugins. If your device can oper a browser - then you can read any document on it
  3. Simple uploading - no need to register. Just enter your email, title of document and select the file, we do the rest. Once the document is ready for you, you will receive automatic email from us.

Previous 10

Next 10