Kawasaki

Copy and paste this link to your website, so they can see this document directly without any plugins.



Keywords

Fuelpak, your, mode, value, harness, with, Remove, other, side, have, power, in-line, from, this, throttle, number., fuel, fully, setting, values, Fuelpak., Turn, turn, verify, wiring, button, first, support, stock, tank

Transcript

IN
ST
A
L
L
A
T
IO
N
I
N
ST
R
U
C
T
IO
N
S
Kawasaki
TOOLS NEEDED
- #2 Phillips Screwdriver
- 4 & 5mm Allen Wrench
- 10mm Socket & Ratchet
Kawasaki Ninja EX650
Fuel Injected Models
INTRODUCTION: Congratulations on your purchase of the Fuelpak
Fuel Management System for your fuel injected Kawasaki Ninja EX 650
motorcycle. Please take the time to read the entire instruction manual
before attempting to install. DO NOT adjust the Fuelpak until you have
thoroughly read the instruction manual and the unit is fully installed. If
you have questions, please call (562) 921-0071.
SUMMARY: To achieve the optimum performance from your
application, it is recommended that you install a high performance
air filter in conjunction with this unit. Fuelpak will be installed in-line
with the factory harness and injectors and also in-line with the factory TPS
(throttle position sensor).
Be sure the main and handlebar switches are in the off position
during the installation process. Failure to do this will cause the
“check engine” light to be set.
Remove rider seat.
Remove fuel tank and fuel tank side covers. (Consult service
manual for proper removal.)
Remove left side cowling (black cover) to access TPS Sensor more
easily later in the install.
Remove 4 screws to the airbox lid. Disconnect the airbox temp
sensor and hoses leading to the airbox. Remove 4 bolts holding
the airbox to the throttle bodies and remove airbox.
Route Fuelpak harness through center of the bike and under the
rear frame rail then over to the left towards the front of the bike.
(Fig 1)
Attach Fuelpak Black wire to the negative side of the battery.
Unplug stock wiring harness from injectors. Plug Fuelpak harness
in-line between the stock wiring harness and each injector.
(Fig 2)
Locate the Throttle Position Sensor on the left side of the bike
towards the rear of the throttle body. (Fig 3)
Plug Fuelpak TPS sensor connector’s in-line of the stock wiring
harness.
Reinstall airbox, fuel tank and all side covers leaving seat off for
set-up of the Fuelpak. You are now ready to set-up your Fuelpak.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
INSTALLATION INSTRUCTIONS FOR P/N 63021
READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
F
U
E
L
I
N
JE
C
T
IO
N
M
A
N
A
G
E
M
E
N
T
S
Y
ST
E
M
Ninja EX650
PLEASE NOTE: FUELPAK RECOMMENDS A HIGH PERFORMANCE AIR FILTER.
NOTICE:ᾨ
Fuelpak is intended for racing use only, and
is not legal for sale or use in California on
pollution-controlled vehicles.
H
O
W
I
T
W
O
R
K
S
E
N
T
E
R
IN
G
V
A
L
U
E
S
Refer to the Fuelpak setting reference to locate the setting values specific to your motorcycle and
exhaust application. If you do not find your setting, visit www.fuelpakfi.com or call tech support at
(562)- 921-0071.
Turn on main power and handlebar switches, and start engine. Fuelpak display should light up, if
not, turn power off and verify all connections are fully seated.
Press mode button once to reach mode 1. (Display should show a “1” under “MODE”.)
Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct
value as indicated in your Setting Value. After entering your first value, press the mode select
button to move to mode 2 and enter the value. Continue until you have entered the value for
each of the first 18 mode positions. Each time the value (+) is pressed; the value increases by one
number. Each time the value (-) is pressed; the value decreases by one number. (Please refer to the
“How It Works” section directly above if you have questions about this step.
By pressing the mode select button three times, move to mode 21 and verify that it reads “0”
when the throttle is closed and increases as you twist the throttle.
Enter any other mode values from mode 23 to mode 36 if your application requires them. (They
will read “N/A” if your application does not require them.)
Turn power off, wait one second then turn power back on. Verify all modes are set correctly and
turn power off.
Secure Fuelpak box with supplied velcro and reinstall seat.
You are now ready to ride.
1.
2.
3.
4.
5.
6.
7.
8.
9.
WARRANTY INFORMATION
WARRANTY: Your Fuelpak unit is warranted against defects
in materials and workmanship for the period of 90 days from
the original retail purchase. In the event of an alleged defect
in material or workmanship, Fuelpak’s responsibility is strictly
limited to repair or replace the defective product. Fuelpak
shall not be responsible for (a) labor, transportation, or other
incidental charges; (b) consequential or other damages
incurred by use of any product. Fuelpak offers no other
warranty beyond this limited warranty. This limited warranty
does not apply to products which have been (a) modified
or altered in any way; (b) subjected to adverse conditions,
such as misuse, neglect, accident, improper installation or
adjustment, contaminants, corrosion, or faulty repair; or (c) used
in applications other than those recommended by Fuelpak. To
initiate a warranty process, the consumer must first call technical
support to receive a return authorization number. The product
must be returned to Fuelpak complete with a dated receipt and
a return authorization number.
Fuelpak
Attn: Warranty Claims
13861 Rosecrans Avenue
Santa Fe Springs, CA 90670
(562) 921-0071
P/N 51610 082609
T
E
C
H
SU
P
P
O
R
T
IN THE EVENT OF A MALFUNCTION, PLEASE CHECK THE FOLLOWING
F
U
E
L
I
N
JE
C
T
IO
N
M
A
N
A
G
E
M
E
N
T
S
Y
ST
E
M
1. Turn off main and handlebar switches then verify all
connectors are fully seated.
2. Be sure setting values are correct for your application.
3. Verify throttle calibration, step 5 in Entering Values.
4. Check harness for cuts, scrapes or abrasions.
5. Make sure the battery is fully charged and the
charging system is operating correctly.
6. Call technical support at (562) 921-0071

PDF Document reader online

This website is focused on providing document in readable format, online without need to install any type of software on your computer. If you are using thin client, or are not allowed to install document reader of particular type, this application may come in hand for you. Simply upload your document, and Docureader.top will transform it into readable format in a few seconds. Why choose Docureader.top?

  1. Unlimited sharing - you can upload document of any size. If we are able to convert it into readable format, you have it here - saved for later or immediate reading
  2. Cross-platform - no compromised when reading your document. We support most of modern browers without the need of installing any of external plugins. If your device can oper a browser - then you can read any document on it
  3. Simple uploading - no need to register. Just enter your email, title of document and select the file, we do the rest. Once the document is ready for you, you will receive automatic email from us.

Previous 10

Next 10